IXIA iBypass 40-10 Manuel utilisateur
-
Quick Install Guide
913-2106-01 Rev A 11/14
I2BP-4x10
iBypassTM 40-10
2
PLEASE READ THESE LEGAL NOTICES CAREFULLY.
Trademarks and Copyrights
Net Optics, and iBypassTM are registered trademarks of Net Optics, Inc. By using the iBypassTM 40-10
Switch, you agree to the terms and conditions of usage set forth by Ixia.
Copyright ©2006-2014 by Net Optics, Inc. with modications Copyright © 2014 Ixia. All rights
reserved.
This publication may not be copied, in whole or in part, without Ixia’s consent.
RESTRICTED RIGHTS LEGEND: Use, duplication, or disclosure by the U.S. Government is subject
to the restrictions set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer
Software clause at DFARS 252.227-7013 and FAR 52.227-19.
Ixia, the Ixia logo, and all Ixia brand names and product names in this document are either trademarks
or registered trademarks of Ixia in the United States and/or other countries. All other trademarks
belong to their respective owners.
The information herein is furnished for informational use only, is subject to change by Ixia without
notice, and should not be construed as a commitment by Ixia. Ixia assumes no responsibility or
liability for any errors or inaccuracies contained in this publication.
This product is covered under the Ixia Limited Warranty and Technical Support Agreement. You can
nd this Agreement by going to the following link -- http://www.ixiacom.com/support/warranty/. Click
on the Limited Warranty and Technical Support Agreement link to view the document.
3
Contents
iBypass 40-10 Switch Content 4
iBypass 40-10 Switch Overview 5
Step 1 6
Rack Mount iBypass 40-10 Switch 6
Step 2 7
Connect Power 7
Step 3 8
Connect Options 8
Step 4 12
Congure the IP 12
Assign IP in Web UI 14
Step 5 16
Connect to Network 16
Step 6 17
Connect to Monitoring Tools 17
Multiple Segments 18
Step 7 19
Check for Recent Updates 19
Support 20
4
iBypass 40-10 Switch Content
This guide provides the initial steps to install and congure the iBypassTM 40-10
Switch.
Carefully unpack the contents and verify you have the following components:
• iBypass 40-10 Switch
• 3-meter RJ45, CAT 5e 4-pair (purple)
• RJ45 to DB9 Console Port to PC cable
• 4 Breakout cables, MTP-4LC, OM4
• Long Ear Extender and Short Ear Extender and eight Phillips screws (10-32 x
5/8) for rack mounting
• Two External Power Supplies (12VDC, 9A, 108W)
• iBypass 40-10 Switch Quick Install Guide (this document)
• iBypass 40-10 Switch User Guide (on CD)
• End User Agreement, Registration Card and Extended Warranty (if purchased)
QSFP+ transceivers are ordered and shipped separately.
Check the packing slip against parts received. If any component is missing or
damaged, contact our Order Management department via email at Order-
5
iBypass 40-10 Switch Overview
Figure 1 - Front View
• Console Port (RJ45) and Management Port (RJ45)
• 2 x 40G Monitor Ports (uses QSFP+ transceivers)
2 x 40G Network Ports (MTP Connectors)
• Hot swappable fans and replaceable power module
Figure 2 - Rear View
2x16 Character Display
Network
Ports
Monitor
Ports
Bypass, Tap, Power
LEDs
Activity & Alarm
LEDs
Management
Port
Console
Port
6
Step 1
Rack Mount iBypass 40-10 Switch
The switch is designed to occupy one rack unit height of a standard 19” rack. Do the
following to install the iBypass 40-10 Switch into an equipment rack:
1. Remove the Ear Extenders and screws from the shipping bag.
2. Attach the Long Ear Extender to the switch if you are only mounting one switch
or attach the Short Ear Extender between two switches if you are mounting two
switches. See Figure 3.
3. Slide the switches in place in the rack.
4. Fasten the switches in place at the front panel ears using the included Phillips
screws.
Figure 3 - Attach Ear Extenders for Rack Mount
Long Ear Extender
for one switch
Short Ear Extender
binds two switches
7
Step 2
Connect Power
Before connecting power, ground the switch to the rack by connecting a 14AWG
minimum ground wired with a #8 ring lug from the switch to a suitable ground
connection on the rack.
Do the following to connect and apply power to the iBypass 40-10 Switch:
1. Plug one of the supplied power cords to a power connector located at the rear
of the chassis. Plug the other end to a power source. See Figure 4.
2. For redundancy, plug the other power cord to the iBypass 40-10. Plug the
other end to a source independent from the rst power source.
The Power LEDs on the front illuminate.
Figure 4 - Power Connections
8
Step 3
Connect Options
Switch Default Settings
The iBypass 40-10 Switch ships with the following default system settings:
IP Address: 10.60.4.180 Monitor and Port Thresholds: 80%
Netmask: 255.0.0.0 Username: admin
Gateway: 10.0.0.1 Password: admin
You have two ways of logging into the iBypass 40-10 Switch.
Connect Option 1 - Connect PC to Management Port
1. Establish a PC you want to use to connect to the switch. Make sure it’s IP
address is on the same subnet as the iBypass switch. The default address
settings of the switch are shown above.
2. Connect one end of the included Cat 5e cable to the PC’s Ethernet port and
connect the other end to the iBypass Management port. See Figure 5.
3. Open a terminal window on the PC and ping 10.60.4.180 to conrm the
connection.
4. After you have conrmed that you have a connection, you can log in via SSH at
the terminal prompt, or enter the default address into the browser URL. Go to
the Assign IP in Web UI section if you want to log in through the Web UI. Go to
the next step if you want to log in to the CLI.
9
5. At the terminal window prompt, type ssh [email protected]. Enter
password admin. The prompt appears.
6. At the prompt, enter admin for the user and admin for the password.
7. Change the password for the admin account by entering the following
command at the prompt:
modify user password admin <new_passwd> <re-enter_passwd>
where <new_passwd> is the new password for the admin account and
<re-enter_passwd> is new password entered again.
8. Go to Congure the IP section and follow the instructions to set a new IP
address.
PC on the same subnet as
iBypass 4x10G switch
Connect Cat 5e cable
from Management port to
PC Ethernet
Figure 5 - PC to Management Port
For more information about using the iBypass 40-10 Switch CLI, enter help to display
command information or see the iBypass 40-10 Switch User Guide for more details.
10
Step 3 (cont.)
Option 2 - Connect PC to the Console Port
1. Connect a PC running terminal emulation software to the iBypass 40-10 Switch
Console port with the supplied RJ45-DB9 console cable. See Figure 6.
2. Launch the terminal emulation software, such as HyperTerminal or minicom,
and set the communication parameters to:
115200 baud 8 data bits no ow control
no parity 1 stop bit
3. At the prompt, enter admin for the user and admin for the password.
4. Change the password for the admin account by entering the following
command at the prompt:
modify user password admin <new_passwd> <re-enter_passwd>
where <new_passwd> is the new password for the admin account and
<re-enter_passwd> is the new password entered again.
5. Go to Congure the IP section and follow the instructions to set a new IP
address.
For more information about using the iBypass 40-10 Switch CLI, enter help to display
command information or see the iBypass 40-10 Switch User Guide for more details.
Table des matières
