Iwata IS-875HT Manuel utilisateur

IWATA STUDIO SERIES TUBULAR SERIES AIR COMPRESSORS — IS-875HT and IS-925HT

TUBULAR SERIES

AIR COMPRESSORS

Congratulations on your new purchase! The Iwata Tubular Series Air Compressors deliver quiet,

clean, pulse free air along with superb moisture separation and precise air pressure adjustment.

IS-875HT and IS-925HT

ANEST IWATA-MEDEA, INC.

Portland, Oregon U.S.A.

+1-503-253-7308

www.Iwata-medea.com

ANEST IWATA AUSTRALIA PTY LTD.

Mt. Druitt, NSW

+61-(02)-9853-2000

www.anest-iwata.com.au

ANEST IWATA EUROPE S.R.L.

Torino, Italy

+39-01-1248-0868

www.anest-iwataeu.com

ANEST IWATA SOUTH-EAST ASIA CO., LTD.

Bangkok, Thailand

+66-(0)-2643-2870

www.anest-iwatasoutheastasia.com

ANEST IWATA SHANGHAI

Shanghai, China

+86-(0)21-6407-9713 / 15 / 16

www.anest-iwata-sh.com/ja

ANEST IWATA RUS LLC

Moscow, Russia

+7-495-938-77-28

www.anestiwata.ru

ANEST IWATA CORPORATION

Yokohama, Japan

+81-(0)45-591-1111

www.anest-iwata.co.jp

ANEST IWATA (U.K.) LTD.

Neots Cambs, England

+44-(0)1480-474742

www.anest-iwata.co.jp

ANEST IWATA MOTHERSON LTD.

Uttar Pradesh, India

+91-(0)120-4600500 / 14 / 17

www.motherson.com

ANEST IWATA SOUTH AFRICA (PTY) LTD.

Johannesburg, Republic of South Africa

+27-11-463-2169/2265/2223

ANEST IWATA DO BRASIL COMERCIAL LTDA.

Bairro do Paraiso, Sao Paulo

+55-11-3171-0072

www.anest-iwata.net.br

CENTURY TRADING CO., LTD.

Seoul, Korea

82-2-2163-0300

www.centrading.co.kr

If you have any issues with this product,

call ANEST IWATA-MEDEA (U.S.A.) 503-253-7308 (M-F 8AM - 4:30PM Pacic Time)

or your local ANEST IWATA aliate before returning to your place of purchase.

NEED ASSISTANCE

The Carry Handle Is The Air Storage Tank

Oil-Less Piston Compressor

Oil-less means oil-less. The compressor uses PTFE gaskets to seal the compression chamber. This allows the compressor to be quiet without

atomizing oil into the air stream, which makes the compressor virtually maintenance free.

Air Pressure Adjustment Knob

Though not a full regulator, the air pressure adjustment knob allows control of the air pressure. It also doubles as the moisture release valve.

Moisture Trap Assembly

The moisture trap lters out the water and debris down to 5 microns.

Air Pressure Gauge

Don’t guess what pressure you’re spraying at — know it! Your “working pressure” (or “working psi”) is what the gauge shows while you have

your trigger pressed down.

Power Switch

You don’t have to unplug the compressor when you want it to stop, just ip the switch.

Thermal Overload Switch

If the compressor ever decides to overheat, the Thermal Overload Switch will turn o your compressor. If this switch cuts in, it’s saving your

compressor. Let it cool down. The switch will automatically reset itself.

Voltage

If you bought the compressor in the country you’re going to use it, it’s completely ready to go. If you’re going to transfer the compressor to

another country with a dierent voltage, you’ll need a plug adapter and the appropriate power converter. WARNING: Using a plug adapter

and power converter may cause unit to overheat. Any issues resulting from the use of a power adapter and/or power converter are

not covered under the Anest Iwata-Medea warranty.

FEATURES

Unpack the compressor and all packaged

components. Enclosed you’ll nd:

a. Smart Jet Plus Compressor (#IS-875HT)

b. Moisture Filter Regulator

c. Airbrush/Spray Gun Holder (with screws)

d. Air Hose (#DT I 10)

e. Adapter Kit (for other brands of airbrush)

f. Smart Jet Plus Manual

EXPLODED DIAGRAM - SMART JET PLUS IS-875HT

EXPLODED DIAGRAM - POWER JET PLUS IS-925HT

Unpack the compressor and all packaged

components. Enclosed you’ll nd:

a. Power Jet Plus Compressor (#IS-925HT)

b. Moisture Filter Regulator

c. Airbrush/Spray Gun Holder (with screws)

d. Air Hose (#DT I 10)

e. Adapter Kit (for other brands of airbrush)

f. Power Jet Plus Manual

1. Screw the moisture lter regulator onto 1/4”tting on compressor.

2. Screw airbrush.spray gun holder onto side metal plate with provided screws.

3. Screw the coiled air hose onto the compressor.

4. Screw the other end of the coiled air hose onto the moisture trap’s small screw.

5. Screw the straight air hose’s big end onto the moisture trap’s big screw.

6. Screw the straight air hose’s small end onto the airbrush.

a. Note: If you’re using a brand of airbrush other than Iwata, use the appropriate adapter from the adapter kit.

You might have to try them out to see which one is right.

7. Place the moisture trap into the compressor’s front-mounted metal ring. The moisture trap should snap into place. By snapping into place

it will not rattle when the unit is running.

8. The airbrush should t into the black airbrush holder by placing the front end of the airbrush into the holder.

9. Plug the compressor into a grounded wall outlet. (Avoid using an extension cord.)

10. Turn the compressor ON by pressing down the switch on top of the unit. The unit will run for a couple seconds then stop. This is OK! When

you push down the trigger on your airbrush, the compressor will come on and when you release the trigger the unit will stop. This is the

Auto Shut-O feature eect. This feature will prolong the life of your motor since the unit doesn’t run the whole time it’s turned on.

11. As the unit is being used, water may collect in the moisture trap’s clear, plastic bowl. Release the water by following the maintenance

instructions on page 9.

GETTING STARTED

1. When you rst hook up your airbrush to your compressor and depress the trigger of your airbrush, the pressure that registers on your gauge

is called your “working pressure.” Your working pressure can vary depending on the size of your airbrush’s nozzle. The smaller the nozzle

size, the higher your working pressure. An average nozzle size of 0.3 mm will expend a working pressure of approximately 25-28 psi with

the Smart Jet.

2. You cannot increase your working pressure, but you can decrease your working pressure by using the air adjustment knob to open the

bleed valve.

3. Adjust the air pressure by turning the air adjustment knob toward the“+” or “–” while spraying air from the airbrush.

REGULATING THE PRESSURE

1. Release any built-up moisture by following the maintenance instructions below.

2. Turn o the compressor.

3. Release any leftover air by pressing down on your airbrush trigger (being careful of any excess paint) or unscrewing your airbrush

from the air hose.

ENDING A SESSION

Releasing Built-Up Moisture

• Release the water by twisting the dial toward the “–” sign.

• This will open the bleed valve and drain o the collected moisture.

• Hold a paper towel under the open valve to collect the water.

• Do not let excess water build up in the moisture trap.

Changing The Air Filter

The lter only needs to be changed if it’s signicantly dirty or dirty enough to cut air ow into the compressor.

• Use your nger to pull the black tab out

• Pull out the sponge-like air-lter

• Replace with new air lter (Part # IS 030 – 10 pack)

• Please inspect your air lter once per week with heavy compressor use.

DO NOT use oil in/on the compressor.

MAINTENANCE

Compressor turns on and o while airbrush is not spraying air.

The compressor has an air leak somewhere. When this happens, try the following steps:

1. Spray all connections with a soapy water solution.

2. Bubbles indicate an air leak.

3. Tighten connection.

4. If bubbling doesn’t stop, try wrapping threads with thread sealant tape (max 3 wraps only) or applying beeswax to the threads.

Both methods provide an airtight seal.

5. If the air leak is in the middle of a hose the hose will need to be replaced.

For any other problems or issues call or contact ANEST IWATA-MEDEA at 503-253-7308 or email at: info@iwata-medea.com

TROUBLESHOOTING

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Iwata Compresseur d'air

Iwata

Iwata IS-800 Manuel utilisateur

Iwata

Iwata IS-50 Silver Jet Manuel utilisateur

Iwata

Iwata IS 35 NINJA JET Mode d’emploi

Iwata

Iwata STUDIO SERIES Manuel utilisateur

Iwata

Iwata Power Jet Series Manuel utilisateur

Iwata

Iwata SMART JET IS-850 Manuel utilisateur

Iwata

Iwata NINJA JET IS35 DE Mode d’emploi

Iwata

Iwata Smart Jet Pro IS-875 Manuel utilisateur

Iwata

Iwata STUDIO SERIES Manuel utilisateur

Iwata

Iwata Ninja Jet IS-35 Manuel utilisateur

Iwata

Iwata STUDIO SERIES Manuel utilisateur

Iwata

Iwata IS 850 SMART JET Manuel utilisateur

Iwata

Iwata WORKSHOP IWC28S Instructions d'utilisation

Iwata

Iwata IS 50 Manuel utilisateur

Iwata

Iwata Silver JET IS50 Mode d’emploi

Iwata

Iwata FREESTYLE AIR Manuel utilisateur

Manuels Compresseur d'air populaires d'autres marques

Sparmax

Sparmax DC-25XR Manuel utilisateur

KAESER

KAESER M122 Manuel utilisateur

GMC

GMC GAC1500 Manuel utilisateur

Briggs & Stratton

Briggs & Stratton Air Compressor Manuel utilisateur

Fini

Fini F3GST2TK Manuel utilisateur

Industrial Air

Industrial Air CP1580325 Manuel de programmation

Campbell Hausfeld

Campbell Hausfeld RP3300 Guide de démarrage rapide

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manuel utilisateur

Hitachi

Hitachi EC99S Manuel de l'opérateur

Parkside

Parkside PKO 270 A1 Manuel utilisateur

Sullair

Sullair 185 Manuel utilisateur

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manuel utilisateur

Ferm

Ferm CRM1046 Manuel utilisateur

BE AC153 Manuel utilisateur

RIDGID

RIDGID OF25150A Manuel utilisateur

Johnson Controls

Johnson Controls QUANTUM LX Manuel

Sears

Sears Craftsman 919.167463 Manuel utilisateur

Ring Automotive

Ring Automotive RAC700 Manuel utilisateur