IPC CT40 R Manuel utilisateur

CT40 R - CT70 R Quick Guide

This Guide is intended for quick consultation only and does not replace the Use and Maintenance Manual.

Before using the machine, read the Use and Maintenance Manual contained in the machine packaging thoroughly and

rigorously respect all the instructions.

PREPARATION/OPERATION

Fill the detergent tank.

Lower the machine head by pressing the pedal

downwards and to the left.

Lower the squeegee using the lever.

Press the brush button to enable brush rotation

and turn the suction motor on.

Choose the direction of movement by moving

the direction selector, turn the potentiometer to

set the work speed.

Press the suction motor button to disable suc-

tion if you want to prewash the surface.

Select working pressure by turning the

adjustment knob.

Operate the drive lever. Pay attention to the LEDs indicating the pres-

sure of the brushes on the work surface. The

following may be displayed:

a) 1 green LED on: minimum pressure;

b) 2 green LEDs on: medium pressure;

c) 3 green LEDs on: maximum permitted

pressure;

d) 3 green LEDs on + 1 red LED on: excessive

pressure.

Begin working

When you have nished cleaning, proceed as

follows:

Turn the brush motor off.

Turn the suction motor off.

Raise the machine head.

Raise the squeegee.

If necessary, charge the batteries.

Press the “H2O” button for at least 2 seconds

to enable detergent ow. Press the button repe-

atedly to vary the quantity delivered.

PLDC01906

DAILY MAINTENANCE

Empty the dirty water drum through the drain

hose.

Clean the dirty water drum.

Check the suction lter is undamaged and

clean.

Check the detergent tank ll lter is undama-

ged and clean.

Check the detergent output lter is undamaged

and clean.

Clean the brush.

Check the squeegee is clean and the blades

are not damaged.

Check the battery charge.

To charge, insert the battery charger connector

into the connector alongside the squeegee

lifting lever.

REPLACING THE SQUEEGEE BLADES

• release the clip;

• remove the two blade retainers by pushing them towards the outside of the squeegee then extracting them;

• remove the blade;

• reuse the same blade by reversing the edge in contact with the oor until all four edges are worn out, or replace with a new blade, tting it onto

the screws on the body of the squeegee;

• reposition the two blade retainers by centring the widest part of the slots over the xing screws on the squeegee body, then pushing the blade

retainers inwards;

• fasten the clip;

AUTOMATIC BRUSH ATTACHMENT

Brush attachment, lift the head by pressing the pedal and t the rollers in their housing by rst inserting them on the drive pulley, then pushing them

upwards until they click into place.

Brush removal, raise the head by pressing the pedal and release the brushes by pulling them downwards from the side opposite the drive pulley,

then extracting them from their housing.

THE MACHINE DOES NOT COME ON/START UP CHECK THE BATTERY CHARGE

THE SUCTION MOTOR DOES NOT WORK CHECK THE DIRTY WATER DRUM IS NOT FULL

CHECK THE DIRTY WATER DRUM LEVEL SENSOR IS NOT BLOCKED/MALFUNCTIONING

THE MACHINE LEAVES THE FLOOR WET CHECK THE SQUEEGEE BLADES ARE NOT WORN

CHECK THERE IS NO DEBRIS BETWEEN THE TWO SQUEEGEE BLADES

CHECK THERE IS NO DEBRIS IN THE SUCTION HOSE

CHECK THE SUCTION FILTER IS UNDAMAGED AND CLEAN

CHECK THE DETERGENT TANK LID IS CLOSED CORRECTLY

CHECK THE SUCTION HOSE IS CORRECTLY ATTACHED TO THE SQUEEGEE

THE MACHINE LEAVES THE FLOOR DIRTY CHECK THE TYPE OF BRUSH/PAD IN USE IS SUITABLE FOR THE TYPE OF DIRT AND FLOOR

THE MACHINE LEAVES STRIPES OF WET FLOOR CHECK THE FLOOR HAS BEEN BRUSHED BEFORE USING THE MACHINE

CHECK THERE IS NO DEBRIS BETWEEN THE TWO SQUEEGEE BLADES

CHECK THE SQUEEGEE BLADES ARE NOT WORN

CHECK THE SQUEEGEE IS CORRECTLY ADJUSTED

PLDC01906

Autres manuels pour CT40 R

Ce manuel convient aux modèles suivants

Autres manuels IPC Machine de plancher

Manuels Machine de plancher populaires d'autres marques

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Manuel utilisateur

Numatic

Numatic ET 4045 Manuel utilisateur

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Manuel utilisateur

Mytee

Mytee 8070 Mytee-Lite Manuel utilisateur

Kärcher

Kärcher B 140 R Manuel utilisateur

Triple S

Triple S Ace 26T1 Manuel utilisateur

Nilfisk-Advance

Nilfisk-Advance SW 750 Manuel utilisateur

Tornado

Tornado Marathon 2000 98190 Manuel

Windsor

Windsor ADMIRAL Admiral 8 Manuel utilisateur

Numatic

Numatic TTB 1117/100 Manuel utilisateur

Tennant

Tennant 8210D Manuel utilisateur

Nobles

Nobles Frontier Manuel du produit

lavina

lavina 21-X Manuel utilisateur

KENT

KENT Edge 28B Manuel utilisateur

Tennant

Tennant 215 Manuel du produit

Windsor

Windsor BDP 51/2000C Manuel utilisateur

CleanFreak

CleanFreak DURA-18HD Manuel utilisateur

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Guide de l'administrateur