IOptron CEM26 Manuel utilisateur

Instruction on Polar Scope Replacement of a CEM26/GEM28 Mount

Toll needed: a set of metric Allen wrench

DO NOT OVER TIGHTEN THE SET SCREW!!!

To Remove/Replace/Rotate a CEM26/GEM28 iPolar:

For GEM28

1. Unthread the red RA rear cover

2. Release two set screws on RA axle.

3. Pull out the iPolar

4. Set the mount in Zero Position and insert a New iPolar

5. Check the iPolar orientation to make sure ALT adjustment will result image vertical movement.

For CEM26

1. Release the screws from side

2. Release the other screw from the bottom

3. Pull out the iPoler

4. Set the mount in Zero Position and insert a New iPolar.

5. Check the iPolar orientation to make sure ALT adjustment will result image vertical movement.

To Install an AccuAlignTM Optical Polar Scope:

The RA axis locking wrench will not be able to be used due to the length of optical polar scope.

The LED brightness is not adjustable. You’ll need to block part of the LED if you would like a dim illumination.

1. Set the mount at Zero Position

2. Insert the optical polar scope. Set any one of major marks on top to assume the 12 o’clock position.

3. Tighten the set screws

4. Thread in the polar scope LED. Plug the 3mm DC plug into the LED and 5.5mm plug into DC 12V OUT socket on

main board.

5. Turn on the mount power to check the LED and polar scope.

Major mark

Polar Scope Alignment

There are three Reticle Adjustment Screws on the side of the Polar scope, as shown in the following photo.

(1) Aim the polar scope to a distant object, such as a flag top or building corner. Adjust the object lens to focus the polar

scope to the object. Adjust the eyepiece to see the dial clearly. Center the object in polar scope by adjusting mount

altitude and azimuth adjustment screws.

(2)Bring the object half the distance to the center by adjusting the reticle adjustment screws. Loose one screw first,

then tighten the other screw(s). Only loose/tighten one screw at a time and very small amount of turn each time to

avoid the reticle totally lost its position. It may take a few minutes to familiarize yourself with the screws that move the

polar scope in the appropriate direction. PLEASE do not over tighten the setting screws. The reticle is made from a

glass.

(3) Rotate the mount 180 degree to bring the mount back to the left side. If you are lucky enough, the object will stay in

center of the polar scope. Otherwise, repeat Step 1 to further move the object to the center. After few times, the object

will stay in center when the mount is flipped from right to left.

Rotate

Center the object

Bring the object

half the distance

to the center

Rotate

Center the object

Bring the object

half the distance

to the center

Reticle Adj. Screws

Objective Lens

Lock Ring

Autres manuels pour CEM26

Ce manuel convient aux modèles suivants

Autres manuels iOptron Support et étagère

iOptron

iOptron HEM27 Manuel utilisateur

iOptron

iOptron CEM25P Manuel utilisateur

iOptron

iOptron CEM25 Manuel utilisateur

iOptron

iOptron SmartStar iEQ45 Manuel utilisateur

iOptron

iOptron CEM120 7300 Manuel utilisateur

iOptron

iOptron CEM40 Manuel utilisateur

iOptron

iOptron CEM120 Manuel utilisateur

iOptron

iOptron CEM60 Manuel utilisateur

iOptron

iOptron SmartStar MiniTower Pro Manuel utilisateur

iOptron

iOptron NI63385 Manuel utilisateur

iOptron

iOptron GEM45 Manuel utilisateur

iOptron

iOptron GEM28 Manuel utilisateur

iOptron

iOptron MiniPier Manuel utilisateur

iOptron

iOptron CEM40 Manuel utilisateur

iOptron

iOptron GEM45G Manuel utilisateur

iOptron

iOptron CEM40EC Manuel utilisateur

iOptron

iOptron HEM27 Manuel utilisateur

iOptron

iOptron Precision AZ/EQ Base Manuel utilisateur

iOptron

iOptron CEM40 Manuel utilisateur

iOptron

iOptron CEM25P Manuel utilisateur

iOptron

iOptron SmartStar CubePro GOTO AltAz Manuel utilisateur

iOptron

iOptron iEQ30 Pro 3000E Manuel utilisateur

iOptron

iOptron 7100P Manuel utilisateur

iOptron

iOptron iEQ30 Pro 3000E Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur

iOptron CEM26 Manuel utilisateur

Manuels Support et étagère populaires d'autres marques