Ioline 300 Manuel utilisateur
Quick Start Guide
Ioline 300/350HF System
Trademarks
Ioline is a trademark of Ioline Corporation. Other product names, logos, designs, titles, words or phrases
mentioned within this publication may be trademarks, service marks, or trade names of Ioline Corpora-
tion or other entities and may be registered in certain jurisdictions including internationally.
Ioline Disclaimer
IOLINE CORPORATION PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES
OR CONDITIONS OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO
EVENT SHALL IOLINE, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY
INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES
FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS
AND THE LIKE), EVEN IF IOLINE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES
ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
Limit of Liability Statement
It is the responsibility of the operator of the printer to monitor the performance of the printer and main-
tain it in proper working condition by following the instructions in this Quick Start Guide and the 300
System User Guide. It is the responsibility of the operator of the printer to follow all safety precautions
and warnings that are described in this User Guide. Ioline Corporation is not responsible for injuries that
may occur as a result of unsafe use. Ioline Corporation is not responsible for substandard operational
performance as a result of failure to maintain the printer as described in Quick Start Guide and the 300
System User Guide.
© 2003-2006 Ioline Corporation. All rights reserved. This manual may not be copied, photocopied, repro-
duced, translated, transmitted or converted to any electronic or machine-readable form in whole or in
part without prior written approval of Ioline Corporation.
Service and Support
If you require assistance with an Ioline product, your local Ioline dealer or authorized service center is
ready to help. Support information is also available 24/7 on the Ioline Web site—or you may contact Ioline
directly:
Ioline Corporation
14140 NE 200th Street
Woodinville,Washington 98072 U.S.A.
Ioline Customer Service Department
Monday through Friday
7:00 A.M. - 5:00 P.M. U.S. Pacic Time
Voice: 1.425.398.8282
Fax: 1.425.398.8383
techsupport@ioline.com
www.ioline.com
User Notice
Part Numbers: (Print) 107077 Rev. 8 • (File) 107070 Rev. 6
Quick Start Guide
Ioline 300 System
Images & Illustrations
Figure 1. Front view of the 300 System and a close-up back of the machine ......... xiv
Figure 2. Unpacking the cutter ........................................................................................... 15
Figure 3. The 301 Software installation screen................................................................ 16
Figure 4. The Ioline software icons will be placed on the desktop ............................ 16
Figure 5. Install the drivers, then insert the USB key into the PC .............................. 16
Figure 6. Locations of the power cord outlet, serial port and USB port ................. 17
Figure 7. Rear view of the computer parallel and serial ports .................................... 17
Figure 8. Adhesive sheet and backing material guidelines ............................................ 18
Figure 9. Align the adhesive sheet with the L-shaped Tray alignment marks ......... 18
Figure 10. Apply the material on top of the Adhesive Sheet on the Tray ................. 19
Figure 11. Blade selection guidelines ................................................................................... 20
Figure 12. Installing the blade in the blade holder ............................................................ 20
Figure 13. A properly adjusted blade .................................................................................. 20
Table of Contents
Safety & Cautions
Visual Reference Guide
Chapter 1 Assembly & Set-up
Assembly ........................................................................................................... 15
Unpacking the 300 System ................................................................................................. 15
Prepare the Production Area ............................................................................................. 15
Step 1: Install the 301 Software ....................................................................................... 16
Step 2: Connect the cutter to the PC ............................................................................. 17
Step 3: Install and adhesive sheet ..................................................................................... 17
Step 4: Install the material and tray ................................................................................. 19
Step 5: Select and adjust the blade ................................................................................... 20
Index
This page intentionally left blank.
The 300 and 350HF are powerful cutting machines. To avoid serious
injury:
nKeep ngers, loose clothing and any objects that might get
tangled in moving parts away from the cutter during opera-
tion.
nBefore using, make sure that the cutter has 9-in of clearance
in front and behind the table to give the moving tray ad-
equate space.
Safety &
Cautions
vii
Figure 1. Front view of the 300 System and a close-up photo of the port and power swith on the back of the machine.
Visual Reference Guide
viii
A. Left end cover
B. Dust cover
C. Carriage (design may
vary)
D. Adhesive sheet, mounted
E. Right end cover
F. Keypad
G. Tray (removeable)
H. Origin (starting point)
I. Thumb nuts (2)
J. Table (non-removeable)
K. Leg (2)
L. Power switch
M. Serial port
N. USB port
O. Power connector
KEY
A
C
F
H
I
M
L
J
K
BD
G
E
N O
Chapter 1
Assembly & Set-up
Assembly
This Quick Start Guide shows how to assemble and set up the Ioline
300 System. Consult the 300 System User Guide on the CD-ROM for
more detailed information about installation and operation. Use the
provided Adobe®Acrobat®viewer to read and cut the User Guide if
necessary.
Unpacking the 300 System
Follow the enclosed instruction sheet to remove the cutter and
Accessory Kit from the box. To avoid injury, always lift the cut-
ter with two people. Check the Packing List and save all packing
materials.
1. Set the cutter on a stable surface.
2. If you purchased an extra tray, lift it off the 300’s Table and set
it aside.
3. Remove the 4 screws holding the Table in place for shipping.
4. Cut the tie wrap that hold the carriage in place and remove all
the packing material. (See Figure 2.)
Prepare the Production Area
Clean the table top and clear any obstacles. Place the cutter 9-inches
away from the wall to allow the material tray to move freely toward
the back.
Save all packing materials.
Note
i
The 300 and 350HF
Systems are heavy and
could cause injury if they
fall.A minimum of two people are
required to safely unpack the cut-
ters and attach them to the stand.
Caution
Figure 2. (Left) remove the shipping screws from the Table and (right) cut the ship-
ping tie wrap holding the carriage.
Tie wrap
10 Ioline 300/350HF System Quick Start Guide
Step 1: Install the 301 Software
1. Insert the 301 Software CD-ROM (packaged in the Accessory
Kit) into the CD-ROM drive.
2. The installation program should automatically start. If it does
not, go to Start Menu>Run. Click on Browse and choose the
CD-ROM drive (often drive D:\). Select iosetup.exe, then Open
and Run.
3. Follow the self-guided installation instructions to install the
Ioline Control Center, 301 Software, Acrobat Reader, and all
manuals. (See Figure 3.)
4. When prompted, answer
‘Yes’ to all questions about
installing drivers.
5. The installation program will
place icons on the desktop
for the 301 Software and
Ioline Control Center. (See
Figure 4.)
6. Power off the computer.
7. Connect the Ioline 301 Software key to the USB port (Figure 5).
Figure 3. The 301 Software installation screen.
Figure 4. The Ioline software icons
will be placed on the desktop.
Figure 5. Install the drivers, then insert the USB key into the PC.
Older 300 and 350HF Systems
used a parallel key rather than
USB, as shown below:
Note
i
Autres manuels pour 300
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Ioline Coupeur
Ioline
Ioline SmarTrac I/S Series Manuel utilisateur
Ioline
Ioline 300 Manuel utilisateur
Ioline
Ioline 350HF Manuel utilisateur
Ioline
Ioline SmarTrac 100 Series Manuel utilisateur
Ioline
Ioline 350HF Manuel utilisateur
Ioline
Ioline SmarTrac I/S Instructions d'installation et d'utilisation
Ioline
Ioline I/S 60 Manuel utilisateur
Ioline
Ioline SmarTrac 100 Series Manuel utilisateur
Ioline
Ioline 300 Manuel utilisateur
