Invacare OCMK01 Instructions de montage

On Chair Mounting Kit

Assembly, Installation and Operating Instructions

Model Nos. OCMK01 and OCMK78

SAVE THESE INSTRUCTIONS

NOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact Carrier/Invacare for

further instruction.

SAFETY SUMMARY

To ensure the safe installation of the On Chair Mounting Kit for the ContourU seating system,

these instructions must be followed:

GENERAL WARNINGS

DO NOT install this equipment without first reading and understanding this

instruction sheet. If you are unable to understand the Warnings, Cautions and

Instructions, contact a healthcare professional, dealer or technical personnel if

applicable before attempting to install this equipment - otherwise, injury or dam-

age may occur.

Unless otherwise noted, installation and adjustments should be made while the

wheelchair is unoccupied

INSTALLATION WARNINGS

The position of the On Chair Mounting Kit in the different mounting bracket

configurations is directly related to the chair's stability. When the On Chair

Mounting Kit is installed on a TILT and/or RECLINING wheelchair, the

wheelchair's stability may decrease. It may be necessary to reposition the FRONT

CASTERS, REAR WHEELS, BACK ANGLE, TILT-IN-SPACE, RECLINE POSI-

TION and/or SEAT DEPTH before use. Refer to appropreate wheelchair owners

manual. Use EXTREME caution when using a new seating position.

Before final tightening, ensure that the brackets will not interfere with the

opperation of the wheelchair, or be in a position to injure the patient or any

attendant.

After ANY adjustments, repair or service and BEFORE use, make sure that all

attaching hardware is tightened securely.

USER WARNINGS

Skin condition should be checked frequently after the installation of any new

seating system.

Your therapist and physician should be consulted if you have any questions regard-

ing individual limitations and needs.

Working with your therapist, physician, and rehabilitation technology supplier is

the best way to assure that the ContourU seating system choice matches your

individual needs.

As the needs of the individual become more complex, the ContourU seating

system evaluation becomes more important.

INSTALLATION OF THE ON CHAIR MOUNTING KIT

BACK MOUNTING HARDWARE (FIGURE 1)

NOTE: Refer to GENERAL and INSTALLATION WARNINGS in the SAFETY SUMMARY in this instruction

sheet.

NOTE: The wheelchair hardware consists of two (2) fixed release clamps and two (2 twist release clamps.

The wheelchair hardware must be mounted facing forward (in front of the canes) with the twist release

clamps at the top and the fixed release clamps at the bottom.

NOTE: The back mounting brackets should be placed on the back cane without interfering with other

wheelchair parts or accessories.

1. Install the four (4) L brackets to the ContourU back. Refer to INSTALLING THE BACK L

BRACKETS in this procedure of the instruction sheet.

2. Install the J brackets onto the L brackets. Refer to INSTALLING/ADJUSTING THE BACK

J BRACKETS in this instruction sheet.

3. Position the back onto the back canes in the desired location.

4. On the back cane, mark the bottom edge of the two (2) lower J brackets and the top edge

of the two (2) upper J brackets as shown in DETAIL "A" of FIGURE 1.

5. Remove the mounting screw, washer, lock washer, and internal threaded mounting screw

from one of the fixed release clamps.

IMPORTANT INFORMATION

The best way to avoid problems related to pressure sores is to understand their causes and

your role in a skin management program.

Your therapist and physician should be consulted if you have questions regarding individual

limitations and needs.

All seats and/or backs should be selected carefully. Working with your therapist, and physician

is the best way to assure that a seat choice matches your individual needs.

As the needs of the individual become more complex, the seat evaluation becomes more

important.

INSTALLATION INFORMATION:

Before you install the On Chair Mounting Kit, determine where the ContourU back cushion

must be placed in relation to the seat cushion. Find the appropriate recline angle and seat

depth, and estimate where the clamps will be mounted. Remove any obstacles on the wheel-

chair back canes and seat rails that might interfere with installation.

The adjustable mounting brackets can be placed in different configurations. It is important to

determine first where the ContourU seating system will be placed in relation to the wheelchair

frame.

To maintain the original center of gravity (CG) of the wheelchair user, the ContourU back will

normally be placed between or behind the back uprights.

Twist

Release

Clamps.

DETAIL "B"

Mark

FRONT OF

WHEELCHAIR

Fixed Release

Clamp

Internal

Threaded

Mounting

Screw

Washer

Mounting

Screw

DETAIL "A"

Upper J Brackets

(Top Edge)

Lower J Brackets

(Bottom Edge)

L Brackets

Back Canes ContourU Back

Mark

Mark Internal Threaded

Mounting Screw

Mounting

Screw

Washer

Back Ccane

Lock

Washer

Lock

Washer

FIGURE 1 - INSTALLATION OF THE ON CHAIR MOUNTING KIT BACK

MOUNTING HARDWARE

6. Install the fixed release clamp onto the back cane so that the fixed release clamp is facing

the front of the wheelchair and the bottom edge is aligned with the mark made in STEP 4

as shown in DETAIL "B" of FIGURE 1.

7. Using the mounting screw, washer, lock washer, and internal threaded mounting screw,

secure the fised release clamp to the back cane. Securely tighten.

8. Repeat STEPS 5-6 to install remaining fixed release clamp.

9. Remove the mounting screw, washer, lock washer, and internal threaded mounting screw

from one of the twist release clamps.

10. Install the twist release clamp onto the back cane so that the twist release clamp is facing

the front of the wheelchair and the top edge is aligned with the mark made in STEP 4 as

shown in DETAIL "B" of FIGURE 1.

11. Using the mounting screw, washer, lock washer, and internal threaded mounting screw,

secure the fixed release clamp to the back cane. Securely tighten.

12. Repeat STEPS 8-9 to install remaining twist release clamp.

13. Install the ContourU back onto the chair. Refer to INSTALLING/REMOVING THE

CONTOUR U SEATING SYSTEM BACK in this instruction sheet.

14. If back depth and or angle adjustments are necessary refer to ADJUSTING THE

CONTOUR U SEATING SYSTEM BACK in this instruction sheet.

INSTALLING THE BACK L BRACKETS (FIGURE 2)

NOTE: When mounting the L brackets to the wood backed ContourU cushion the L brackets may be

reversed to allow for greater seat depth adjustments as shown in DETAIL A of FIGURE 2.

1. Position the ContourU Back between the back canes and determine the mounting posi-

tions for the four (4) L brackets to obtain the desired back depth.

2. If mounting L bracket to a pan back, pull to remove the ContourU cushion from the pan

back.

3. Align L bracket with the edge of the seat back and two (2) desired mounting holes as

shown in FIGURE 1.

4. Perform one (1) of the following:

A. PAN BACK: Using a backing plate and two (2) mounting screws, secure the L bracket

to the pan back.

B. WOOD BACK: using two (2) mounting screws secure the L bracket to the wood back.

5. Repeat STEPS 3-4 for remaining three (3) L brackets.

6. If mounting L bracket to a pan back, reinstall the ContourU cushion onto the back pan.

Backing Plate

Mounting Screws

WOOD BACKPAN BACK

Mounting Holes

Edge of the Seat Back

NOTE: ContourU cushion

not shown.

L Bracket

Mounting Screws

Mounting Holes

Edge of the Seat Back

L Bracket

Pan Back

Mounting

Screws

Mounting

Holes

L Bracket

(Reversed)

DETAIL "A"

FIGURE 2 - INSTALLING THE BACK L BRACKETS

INSTALLING THE BACK J BRACKETS (FIGURE 3)

1. Position the ContourU back between the back canes to determine the approximate

mounting position of the J brackets to obtain the desired depth.

2. Align two (2) of four (4) mounting holes of the J bracket with two (2) of five (5) mounting

holes on the L bracket as shown in FIGURE 3.

3. Using two (2) mounting screws and locknuts, secure the J bracket to the L bracket. Se-

curely tighten mounting hardware.

4. Repeat STEPS 2-3 with three (3) remaining brackets.

Locknuts

Mounting Screw

J Bracket

ContourU Back

L Brackets

Mounting Holes

FIGURE 3 - INSTALLING THE BACK J BRACKETS

INSTALLING/REMOVING THE CONTOUR U SEATING

SYSTEM BACK (FIGURE 4)

Installing

1. Ensure that the twist release clamps are in the OPEN position as shown in DETAIL A of

FIGURE 4.

2. Position the two (2) lower J brackets securely into the two (2) fixed release clamps as

shown in FIGURE 4.

3. Position the upper two (2) J brackets against the back canes just below the two (2) twist

release clamp.

4. Rotate the two (2) twist release clamps to the CLOSED position as shown in DETAIL B

of FIGURE 4.

Removing

1. Rotate the two (2) twist release clamps to the OPEN position as shown in DETAIL B of

FIGURE 4.

2. tilt the top of the ContourU back forward away from the back canes.

3. Puilling UP, remove the ContourU back from the back canes.

Twist Release

Clamps.

(OPEN Position)

Fixed Release

Clamp

J Bracket

Back Canes ContourU

Back

DETAIL "B"DETAIL "A"

J Bracket

Twist Release Clamps.

(CLOSED Position)

Fixed Release Clamp

J Brackets

Back Canes ContourU

Back

FIGURE 4 - INSTALLING/REMOVING THE CONTOUR U BACK

ADJUSTING THE CONTOUR U

BACK DEPTH (FIGURE 5)

NOTE: There are six (6) depth adjustments avail-

able on the ContourU with a pan back.

NOTE: There are twelve (12) depth adjustments

available on the ContourU with a wood back. Six

(6) mounting positions with the L brackets facing

the front of the wheel chair and six (6) mounting

positions with the L brackets facing the rear of the

wheel chair as shown in FIGURE 5.

NOTE: All four (4) J brackets should be adjusted to

the same depth unless back angle adjustment is

necessary. Refer to ADJUSTING THE CONTOUR U

SEATING SYSTEM BACK ANGLE in this instruction

sheet after performing this procedure.

1. If necessary, remove the ContourU back.

Refer to INSTALLING/REMOVING THE

CONTOUR U SEATING SYSTEM BACK

in this instruction sheet.

2. Remove the two (2) mounting screws and

locknuts that secure the J bracket to the L

bracket.

3. Align two (2) mounting holes of the J

bracket with two (2) mounting holes of

the L bracket to acquire the desired

depth as shown in DETAIL A of FIG-

URE 5 .

4. Reinstall the two (2) mounting screws and

locknuts that secure the J bracket to the L

bracket. Securely tighten.

5. Repeat STEPS 3-4 to adjust the remaining

three (3) J and L brackets.

6. Reinstall the ContourU back onto the

wheelchair. Refer to REMOVING/IN-

STALLING THE CONTOUR U SEATING

SYSTEM BACK in this instruction sheet.

7. Ensure the ContourU back is set to the

desired depth. If necessary repeat STEPS

1-7 until desired depth is achieved.

ADJUSTING THE ON CHAIR MOUNTING KIT MOUNTING

HARDWARE FOR THE CONTOUR U SEATING SYSTEM

BACK

NOTE: Refer to GENERAL and INSTALLATION WARNINGS in the SAFETY SUMMARY in this instruction

sheet.

Locknuts

Mounting

Screws J Bracket

Mounting Holes

L Bracket

DEPTH ADJUSTMENTS

Pan or Wood Back Additional Positions

For Wood Back Only

DETAIL "A"

FIGURE 5 - ADJUSTING THE

CONTOUR U SEATING SYSTEM

BACK DEPTH

ADJUSTING THE CONTOUR U SEATING SYSTEM BACK ANGLE

(FIGURE 6)

NOTE:Beforeperformingthisprocedure all four(4) J bracketsmust be adjustedto the samedepth.

Refer to ADJUSTING THE CONTOUR U SEATING SYSTEM BACK DEPTH in this instruction

sheet.

NOTE: The back to seat angle is adjusted by repositioning the top and/or the bottom J brackets.

NOTE:AdjustmentsmadetoJbracket(s)ononesideoftheContourUbackMUSTbealsobemade

to the remaining J bracket(s) on the opposite side of the ContourU back.

1. If necessary, install the ContourU back. Refer to REMOVING/INSTALLING THE CON-

TOUR U SEATING SYSTEM BACK in this instruction sheet.

2. With the ContourU back installed on the wheelchair, determine which J bracket mounting

positions are necessary to achieve the desired back angle adjustment.

3. Remove the ContourU back. Refer to REMOVING/INSTALLING THE CONTOUR U

SEATING SYSTEM BACK in this instruction sheet.

4. Remove the two (2) mounting screws and locknuts that secure the J bracket to the L

bracket as shown in DETAIL A of FIGURE 6.

5. Align two (2) mounting holes of the J bracket with two (2) mounting holes of the L bracket

to acquire the desired angle.

6. Reinstall the two (2) mounting screws and locknuts that secure the J bracket to the L

bracket. Securely tighten.

7. Repeat STEPS 4-6 to adjust the remaining J and L brackets as necessary to achieve the

desired back angle.

8. Reinstall the ContourU back onto the wheelchair. Refer to REMOVING/INSTALLING THE

CONTOUR U SEATING SYSTEM BACK in this instruction sheet.

9. Ensure the ContourU back is set to the desired angle and does not interfere. If necessary

repeat STEPS 1-7 until desired depth is achieved.

FIGURE 6 - ADJUSTING THE CONTOUR U SEATING SYSTEM BACK

ANGLE

Upper J Brackets

ContourU Back

Locknuts

Mounting

Screws J Bracket

Mounting Holes

L Bracket

DETAIL "A"

Lower J Brackets

INSTALLATION OF ON CHAIR MOUNTING KIT SEAT

MOUNTING HARDWARE (FIGURE 7)

NOTE: Refer to GENERAL and INSTALLATION WARNINGS in the SAFETY SUMMARY in this instruction

sheet.

NOTE: The wheelchair hardware consists of two (2) fixed release clamps and two (2) twist release

clamps. The wheelchair hardware must be mounted facing up (on top of the seat rails) with the twist

release clamps at the front and the fixed release at the rear of the seat rails.

NOTE: The seat mounting brackets should be placed on the seat rail without interfering with other

wheelchair accessories.

1. Install the L brackets onto the ContourU seat. Refer to INSTALLING THE SEAT L

BRACKETS in this instruction sheet.

2. Install the J brackets onto the L brackets. Refer to INSTALLING/ADJUSTING THE SEAT J

BRACKETS in this instruction sheet.

3. Position the ContourU seat onto the seat rails in the desired location.

4. On the seat rails, mark the front edge of the two (2) front J brackets and the rear edge of

the two (2) rear J brackets as shown in DETAIL "A" of FIGURE 7.

5. Remove the mounting screw, washer, lock washer, and internal threaded mounting screw

from one of the fixed release clamps.

6. Install the fixed release clamp onto the seat rail so that the open end of the fixed release

clamp is facing the front of the wheelchair and aligned with the mark made in STEP 4 as

shown in DETAIL "B" of FIGURE 7.

7. Using the mounting screw, washer, lock washer, and internal threaded mounting screw,

secure the fised release clamp to the seat rail. Securely tighten.

8. Repeat STEPS 5-6 to install remaining fixed release clamp.

9. Remove the mounting screw, washer, lock washer, and internal threaded mounting screw

from one of the twist release clamps.

10. Install the twist release clamp onto the seat rail so that open end of the twist release clamp

is facing the rear of the wheelchair and is aligned with the mark made in STEP 4 as shown

in DETAIL "B" of FIGURE 7.

11. Using the mounting screw, washer, lock washer, and internal threaded mounting screw,

secure the twist release clamp to the back cane. Securely tighten.

12. Repeat STEPS 8-9 to install remaining twist release clamp.

13. Install the ContourU seat on to the wheelchair. Refer to INSTALLING/REMOVING THE

CONTOUR U SEATING SYSTEM SEAT in this instruction sheet.

14. If seat depth and or angle adjustments are necessary refer to ADJUSTING THE

CONTOUR U SEATING SYSTEM SEAT in this instruction sheet.

Twist Release

Clamps.

DETAIL "B"

Mark

Fixed Release

Clamp

Internal Threaded

Mounting Screw

Washer

Mounting

Screw

DETAIL "A"

Front J Brackets

(Front Edge)

Rear J Brackets

(Rear Edge)

L Brackets

Seat Rail

ContourU Back

Mark

Internal Threaded

Mounting Screw

Mounting

Screw

Washer

Seat Rail (Top)

Lock

Washer

Lock

Washer

FIGURE 7 - INSTALLATION OF THE ON CHAIR MOUNTING KIT SEAT

MOUNTING HARDWARE

REAR OF

WHEELCHAIR

FRONT OF

WHEELCHAIR

Ce manuel convient aux modèles suivants

Autres manuels Invacare Aide à la mobilité

Invacare

Invacare RPL450-1 Instructions de montage

Invacare

Invacare 9805 Manuel utilisateur

Invacare

Invacare Twister Manuel utilisateur

Invacare

Invacare 2218 Instructions de montage

Invacare

Invacare 1538345-0125 Manuel utilisateur

Invacare

Invacare Camlock Upgrade Kit 1052250 Manuel utilisateur

Invacare

Invacare Rollator Manuel utilisateur

Invacare

Invacare Growth Bracket Manuel utilisateur

Invacare

Invacare Color Collection Manuel utilisateur

Invacare

Invacare TDX Spree Mode d’emploi

Invacare

Invacare Kirilos Manuel utilisateur

Invacare

Invacare 6098 Manuel du propriétaire

Invacare

Invacare 1141466 Instructions de montage

Invacare

Invacare MB-54 Instructions de montage

Invacare

Invacare 9670 Manuel utilisateur

Invacare

Invacare 65510 Instructions de montage

Invacare

Invacare 1048085 Instructions de montage

Invacare

Invacare Powered Seating Manuel utilisateur

Invacare

Invacare Dolomite Melody Series Manuel utilisateur

Invacare

Invacare Dolomite HP Manuel utilisateur

Invacare

Invacare FDX Manuel utilisateur

Invacare

Invacare 7714P Manuel utilisateur

Invacare

Invacare H140 Manuel utilisateur

Invacare

Invacare Rollator Manuel utilisateur

Manuels Aide à la mobilité populaires d'autres marques

Alber

Alber Scalamobil iQ Manuel utilisateur

Ferno

Ferno CCT-PX Manuel utilisateur

HEPRO

HEPRO Gripo Manuel utilisateur

Otto Bock

Otto Bock Pheon 3R62 Manuel utilisateur

NRS Healthcare

NRS Healthcare M11090 Manuel utilisateur

Medline

Medline MDS86835DSHEC Guide d'installation

Guldmann

Guldmann Twin Turner II Manuel utilisateur

Drive

Drive ROOMBA Manuel utilisateur

Gate

Gate Balder Manuel utilisateur

Decon wheel

Decon wheel TNS Notos Manuel utilisateur

ExoAtlet

ExoAtlet ExoAtlet-II Manuel utilisateur

Rhythm Healthcare

Rhythm Healthcare B3800F Manuel utilisateur

AMF-BRUNS

AMF-BRUNS PROTEKTOR Manuel utilisateur

Drive DeVilbiss Healthcare

Drive DeVilbiss Healthcare OTTER Manuel utilisateur

Rhythm Healthcare

Rhythm Healthcare C500U Manuel utilisateur

Lumex

Lumex RJ4200A Manuel utilisateur

Rebotec

Rebotec Jumbo Manuel utilisateur

Rehaforum MEDICAL

Rehaforum MEDICAL PR50548 Manuel utilisateur