Intermec ScanImage 1470B Manuel utilisateur
1470B Imager
Quick Start Guide
ii 1470B Imager Quick Start Guide
Intermec Technologies Corporation
Corporate Headquarters
6001 36th Ave. W.
Everett, WA 98203
U.S.A.
www.intermec.com
The information contained herein is proprietary and is provided solely
for the purpose of allowing customers to operate and service Intermec-
manufactured equipment and is not to be released, reproduced, or used
for any other purpose without written permission of Intermec.
Information and specifications contained in this document are subject
to change without prior notice and do not represent a commitment on
the part of Intermec Technologies Corporation.
©2004 by Intermec Technologies Corporation. All rights reserved.
The word Intermec, the Intermec logo, Norand, ArciTech, CrossBar,
Data Collection Browser, dcBrowser, Duratherm, EasyCoder,
EasyLAN, Enterprise Wireless LAN, EZBuilder, Fingerprint, i-gistics,
INCA (under license), InterDriver, Intermec Printer Network
Manager, IRL, JANUS, LabelShop, Mobile Framework, MobileLAN,
Nor*Ware, Pen*Key, Precision Print, PrintSet, RoutePower, TE 2000,
Trakker Antares, UAP, Universal Access Point, and Virtual Wedge are
either trademarks or registered trademarks of Intermec Technologies
Corporation.
Throughout this manual, trademarked names may be used. Rather
than put a trademark (™or ®) symbol in every occurrence of a
trademarked name, we state that we are using the names only in an
editorial fashion, and to the benefit of the trademark owner, with no
intention of infringement.
There are U.S. and foreign patents pending.
Contents
1470B Imager Quick Start Guide iii
Contents
Unpacking the Imager ......................................................... 5
Configuring the Imager ....................................................... 6
Keyboard Wedge Interface..................................... 6
Serial/RS-232 Interface.......................................... 8
Scanning a Label................................................................ 10
Where to Go From Here ................................................... 11
Useful Bar Codes............................................................... 11
Test Bar Codes .................................................................. 12
Regulatory Statements ....................................................... 15
iv 1470B Imager Quick Start Guide
1470B Imager Quick Start Guide 5
Unpacking the Imager
When you remove the imager from its box, save the box and
shipping material in case you need to ship or store the imager.
147XU07.eps
1470B Imager Shipping Box Contents
The imager shipping box contains:
• 1470B Imager (standard or high density)
• CD with Visual Menu and QuickView
• 1470B Imager Quick Start Guide (P/N 067055)
You can also order these optional accessories:
• Power supply and power cords
• Battery pack
• Communication cables for a keyboard wedge interface,
RS-232 interface, 241X terminal, or 700 Series computer
• Holder or scanner stand
• 1470/1471 Imager User’s Manual (P/N 067054)
6 1470B Imager Quick Start Guide
Configuring the Imager
You need to program the imager for your interface before you
can transmit bar code data to your computer. You can configure
the imager for:
• a keyboard wedge interface. See the next section, “Keyboard
Wedge Interface.”
• a serial port (RS-232) interface. RS-232 is the default
configuration; however, you still need to program the imager
for the RS-232 interface. See “Serial/RS-232 Interface” on
page 8.
Note: The RS-232 interface is only compatible
with applications that can retrieve data from the
computer’s COM port.
Keyboard Wedge Interface
1 Connect the power supply (4 to 9V) to the keyboard wedge
interface cable and plug in the power supply.
Or, charge and install the battery pack in the imager.
The imager beeps twice.
147XG06.eps
Keyboard Wedge Interface: This illustration shows connecting the
power supply, but you can also charge and install the battery pack in the
imager.
1470B Imager Quick Start Guide 7
2 Connect the keyboard wedge interface cable to the imager.
Note: Do not connect the cable to your computer
yet.
3 Scan these bar codes in order:
Terminal ID
0
0
3
Save
The imager beeps twice during the configuration process.
4 Turn off power to the computer.
5 Disconnect the keyboard cable from the back of the
computer.
6 Connect the computer and the keyboard to the keyboard
wedge interface cable.
7 Turn on power to the computer and wait for it to boot.
8 Open a keyboard application, such as Notepad.
8 1470B Imager Quick Start Guide
9 Scan the following test bar code to make sure that the imager
works.
Code 39 Test Bar Code
BC321
The imager should beep once, and “BC321” should appear in
the keyboard application.
The imager is now connected and ready to communicate with
your computer. To program the 1470 for other keyboard wedge
interfaces, see “Terminal Interface” in Chapter 3 of the
1470/1471 Imager User’s Manual.
Serial/RS-232 Interface
1 Connect the power supply (4 to 9V) to the serial interface
cable and plug in the power supply.
Or, charge and install the battery pack in the imager.
The imager beeps twice.
147XG07.eps
Serial/RS-232 Interface: This illustration shows connecting the power
supply, but you can also charge and install the battery pack in the imager.
1470B Imager Quick Start Guide 9
2 Connect the serial interface cable to the imager.
Note: Do not connect the cable to your computer
yet.
3 Scan these bar codes in order:
Terminal ID
0
0
0
Save
The imager beeps twice during the configuration process.
4 Turn off power to the computer.
5 Connect the serial interface cable to the computer.
6 Turn on power to the computer.
7 Open your application.
10 1470B Imager Quick Start Guide
8 Scan the following test bar code to make sure that the imager
works.
Code 39 Test Bar Code
BC321
The imager should beep once, and “BC321” should appear in
your application.
The imager is now connected and ready to communicate with
your computer. To program the communication parameters for
a serial interface, see “Communication Settings” in Chapter 3 of
the 1470/1471 Imager User’s Manual.
Scanning a Label
The imager’s view finder projects a bright red aiming beam that
corresponds to the imager’s horizontal field of view. The aiming
beam should be centered over the bar code, but it can be
positioned in any direction for a good read.
Linear Bar Code 2D Matrix Bar Code
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Intermec Lecteur de codes-barres
Intermec
Intermec IF30 Manuel utilisateur
Intermec
Intermec ScanPlus 1800 Manuel utilisateur
Intermec
Intermec ScanPlus 1802 Guide de référence
Intermec
Intermec SR61T1D Manuel utilisateur
Intermec
Intermec Sabre 1555 RFID Manuel utilisateur
Intermec
Intermec SR61T Manuel utilisateur
Intermec
Intermec Janus 2010 Manuel utilisateur
Intermec
Intermec EasyCoder PF2i Manuel utilisateur
Intermec
Intermec SR61 Manuel utilisateur
Intermec
Intermec SF61 Manuel utilisateur
Intermec
Intermec ScanPlus 1800 Manuel
Intermec
Intermec SR61B Manuel utilisateur
Intermec
Intermec IF30 Manuel utilisateur
Intermec
Intermec SR31T Manuel utilisateur
Intermec
Intermec IF61 Manuel utilisateur
Intermec
Intermec EasyCoder F4 Mode d’emploi
Intermec
Intermec Sabre 1553 Guide de configuration
Intermec
Intermec SF51 Manuel utilisateur
Intermec
Intermec ScanPlus 1800VT Manuel
Intermec
Intermec IF5 Manuel utilisateur
Manuels Lecteur de codes-barres populaires d'autres marques
POSMicro
POSMicro Datalogic PowerScan D7100 Manuel utilisateur
Marson
Marson MT780 Guide de configuration rapide
NCR
NCR RealPOS Manuel utilisateur
Motorola
Motorola SE3300 Guide de configuration rapide
Element
Element P130BT Manuel utilisateur
Motorola
Motorola Symbol LS3008 Manuel d'installation et d'exploitation
