Intermatic ET100 SERIES Manuel du propriétaire

ET100 SERIES EASY-SET BASIC PROGRAMMING

RESET TIME SWITCH:

1. Place the two position switch to AUTO and the three position

switch to RUN.

2. Press the RESET switch for 3-5 seconds to reset the

microprocessor memory and clear all programmed information. The

display will flash 12:00 AM.

NOTE: Do not press the RESET switch after programming has begun

or you will loose all of your programmed information.

TO SET PRESENT TIME OF DAY:

1. Place the two position switch to AUTO and the three position switch

to TIME SET.

2. Press the HOUR and MIN buttons separately to select the current

time of day. Note that this timer is a 12 hour AM/PM time clock.

TO PROGRAM TIMES :

1. Place the three position switch to PROGRAM. Note that the display

now shows 0:00 1 for Event #1. There are 8 possible programmed

times (events), 4 ON and 4 OFF. All available events need not be

used.

2. Press the HOUR and MIN buttons separately to program the first

ON time desired.

3. Press the EVENT button once. Note that the display now shows

0:00 2 for Event #2.

4. Press the HOUR and MIN buttons for the first OFF time. If more

than 1 ON and 1 OFF time (event) is required per day repeat this

procedure for up to 4 ON and 4 OFF times (events).

5. Return the three position switch to the RUN position and make sure

the two position selector switch is in the AUTO position.

TO REVIEW PROGRAMMED TIMES:

1. Place the three position switch to PROGRAM.

2. Press the EVENT button to review each of the 8 set points.

TO CHANGE PROGRAMMED TIMES:

1. Place the three position switch to PROGRAM.

2. Press the EVENT button until the desired time to change is

displayed.

3. Press the HOUR and MIN buttons separately to change the

displayed time to the new time desired.

4. Press the EVENT button to proceed to the next programmed event

to change if desired and follow previous procedure. If not return the

three position switch to the RUN position.

TO DELETE A PROGRAMMED TIME:

1. Place the three position switch to PROGRAM.

2. Press the EVENT button until the desired time to delete is

displayed.

3. Press the ON/OFF button twice to delete that time. The display will

now show 0:00 and the event number.

4. Return the three position switch to RUN.

TO OVERRIDE PROGRAM:

Program can be overridden at any time by placing the two position

switch to MANUAL. Programmed set times will be maintained but will

not operate the controlled load automatically.

TO MANUALLY OPERATE LOAD:

1. Place the two position switch to either MANUAL or AUTO.

2. Place the three position switch to RUN and depress the ON/OFF

button.

NOTE: The display will show your load toggle ON or OFF.

TO OPERATE TIMER:

Place the two position switch to AUTO and the three position switch to

RUN.

NOTE: When finished programming you may have to toggle your load

ON or OFF depending on the state it should be in at that time by

depressing the ON/OFF button.

NOTE: For assistance please contact Intermatic Technical Services at

815-675-7000.

Table des matières

Autres manuels Intermatic Changer

Intermatic

Intermatic ET8415 Manuel

Intermatic

Intermatic EH10 Manuel utilisateur

Intermatic

Intermatic ET8000 SERIES Manuel utilisateur

Intermatic

Intermatic Grasslin GM40AV Series Manuel

Intermatic

Intermatic HB12R Manuel

Intermatic

Intermatic WH40 Manuel utilisateur

Intermatic

Intermatic ET70815CR Manuel utilisateur

Intermatic

Intermatic Grasslin DTAV40E Manuel utilisateur

Intermatic

Intermatic T21004R Manuel

Intermatic

Intermatic FM1D14 Series Manuel utilisateur

Intermatic

Intermatic IDIGITAL DT104 Guide d'installation

Intermatic

Intermatic GM40AVE-RD89 Series Manuel utilisateur

Intermatic

Intermatic T7401BC Manuel

Intermatic

Intermatic ET171CR Manuel

Intermatic

Intermatic EI500 Series Mode d’emploi

Intermatic

Intermatic ET2825C Manuel

Intermatic

Intermatic T7801B Manuel

Intermatic

Intermatic T7801BC Manuel

Intermatic

Intermatic T1975BCR Manuel

Intermatic

Intermatic T1975 Manuel

Intermatic

Intermatic T8805P101C Manuel

Intermatic

Intermatic ET102CM Manuel utilisateur

Intermatic

Intermatic P4243ME Manuel de service

Intermatic

Intermatic T1976 Manuel

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur