Interlogix TVK-800 Manuel utilisateur

TVK-800 User Manual

P/N 1072696A • REV • ISS 13MAY14

2014 United Technologies Corporation.

Interlogix is part of UTC

Building and Industrial Systems, a unit of

United Technologies Corporation

Trademarks and

patents

Trade names used in this document may be trademarks or

registered trademarks of the manufacturers or vendors of the

respective products.

Manufacturer

United Technologies Corporation

2955 Red Hill Avenue, Costa Mesa, CA 92626

-5923, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, The Netherlands

FCC compliance

Class A

: This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own

expense.

Canada

This Class A digital apparatus complies with Canadian ICES

-003.

Cet appareil mumérique de la classe

A est conforme à la norme

NMB

-003 du Canada.

ACMA compliance

Notice!

This is a Class A product. In a domestic environment this

product may cause radio interference in which case the user may be

required to take adequate measures.

Certification

N4131

EU directives

2004/108/EC (EMC directive)

: Hereby, UTC Building and Industrial

Systems

declares that this device is in compliance or with the

essential requirements and other relevant provisions of Directive

2004/108/EC.

2002/96/EC (WEEE

directive): Products marked with this symbol

cannot be disposed of as unsorted municipal waste in the European

Union. For proper recycling, return this product to your local supplier

upon the purchase of equivalent new equipment, or dispose of it at

design

ated collection points. For more information see:

www.recyclethis.info.

Contact information

For contact information

, see www.interlogix.com or

www.utcfssecurityproducts.eu

TVK-800 User Manual i

Content

Introduction 3

Features 3

Package contents 4

Installation environment 4

Description 5

Connections 5

Keypad description 6

Function keys 6

Playback control dial and keys 7

Select options on the LCD display 8

Joystick operation 8

Using the key commands 8

Overview of the user groups 10

Logging in/out 11

Menu overview 13

Keypad configuration via the web browser 14

Keypad management 15

Device management 16

User management 16

Input settings 18

Output list 20

Auxiliary functions 21

Live view and PTZ speed settings 21

FTP settings 21

System status 22

Local keypad configuration by the Administrator 24

Keypad management 24

Device management 29

Local live view 33

Playback a file 33

User management 35

Camera settings 37

Output settings 38

Macro settings 40

Playback files from a recorder 41

Advanced settings 42

Log out of the keypad 44

Reboot the keypad 44

Shutdown 44

ii TVK-800 User Manual

Local keypad configuration by the Manager 45

Logging in/out 45

Display list of accessible devices 46

Local live view 46

Playback a file 47

User management 48

Input settings 49

Output settings 50

Macro settings 50

Playback files from an encoder 51

Advanced settings 51

Log out of the keypad 51

Reboot the keypad 51

Shutdown 51

Local keypad configuration by the Operator and Custom users 52

Logging in/out 52

Display list of accessible devices 52

Change password 53

Shutdown 53

Using the keypad 54

Using shortcut operations 54

Local live view 54

Display decoded video on a monitor 55

Instant playback 61

Auxiliary functions 61

Saving recordings 62

Moving to next/previous cameras 63

Operating PTZ cameras 64

Setting a preset 64

Calling up a preset 65

Setting a preset tour 66

Calling up a preset tour 67

Setting a shadow tour 68

Calling up a shadow tour 69

Specifications 70

Index 71

TVK-800 User Manual 3

Introduction

Features

Hardware

•7’’ TFT touch screen at 800×480 resolution

•4-axis joystick

•Shortcut keys for PTZ control, setting and calling of preset, preset tour, and shadow

tour

•Shortcut keys for playback operation

•Shortcut keys for input groups and output groups

•Shortcut keys for wiper and light control operation

Software

•Admin, manager, operator, and custom user management

•Supports upgrade by USB flash drive

•Auto searches connected devices in the same network area

•Imports and exports keypad configuration parameters

•Macro command operation

•Storage of recorded files and snapshots to USB flash drive or FTP server

•Plays back recorded files from the USB flash drive

•Plays back remotely recorded files

•Bidirectional audio

•Supports configuration by web server

Decoding capability

•Provides 1-ch video decoding

•Supports standard MPEG4 and H.264 encoding formats

•Decodes at up to 720P real-time resolution

Display decoded video on the monitor

•Displays a decoded camera on the selected window

•Displays a decoded camera group on the selected window

•Sequences a display of a decoded camera group on a monitor

•Sequences a display of a decoded camera group on a monitor group

4 TVK-800 User Manual

Package contents

When you receive the product, check the package and contents for damage and verify

that all items are included. If any items are damaged or missing, please contact your

local supplier.

Items shipped with the product include:

•TVK-800 keypad

•Power supply unit (PSU)

•Power supply cords (UK and Europe)

•CD-ROM

•User manual

Installation environment

When installing your keypad, consider these factors:

Ventilation: Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions. Ensure that the location planned for the installation of the

unit is well ventilated and dust-free.

Temperature: Consider the device’s operating temperature (-10 to +55 ºC, 14 to

131 °F) and noncondensing humidity specifications (10 to 90%) before choosing an

installation location. Do not install the device on top of other hot equipment.

Moisture: Do not use the unit near water. To reduce the risk of fire or electric shock, do

not expose this unit to rain or moisture.

Electrical: Ensure that the device is connected to a power supply that corresponds with

the characteristics listed in the technical specifications.

Working surface: Place the device on a horizontal solid surface. Avoid exposure to

severe vibrations.

Caution: Do not attempt to dismantle this product. Any attempt to dismantle or remove

the covers from this product will invalidate the warranty and may also result in serious

injury.

TVK-800 User Manual 5

Description

This chapter describes how to connect the keypad as well the functions of the different

keys on the keypad.

Connections

Figure 1: Back view of the keypad

1. Touch pen

2. GND

3. Line in

4. Audio out

5. Reserved

6. RS-485 interface

7. LAN, PoE (802.3af)

8. RS-232 interface

9. USB interface

10. 12 VDC power supply

11. Power on/off

6 TVK-800 User Manual

Keypad description

Figure 2: Keypad top view

1. Playback control

See “Playback control dial and keys” on

page 7 for further information.

2. Function keys

Each key has a special function. See

“Function keys” below for further

information.

3. Numeric keys

Input numbers as well as ESC and

ENTER.

4. Lens control keys

Zoom in or out, focus near or far, open or

close iris.

5. 4-axis joystick.

Control pan, tilt and zoom as well as

capture snapshots. See “Joystick

operation” on page 8 for further

information.

6. Turn light and wiper on or off.

7. Touch-sensitive LCD display

8. LED indicators:

POWER: Lit when keypad is powered up.

LINK: Lit when the keypad is connected to

the network.

Tx/Rx: Flickers when the keypad is

transmitting/receiving data.

COM: Reserved.

ALARM: Reserved.

Function keys

There are 20 function keys. They allow you to quickly select regularly used functions

such as to call up presets or to select a monitor.

See Figure 2 above for the location of the function keys on the keypad.

The keys are lit blue when inactive and red when active.

TVK-800 User Manual 7

Figure 3: Description of the function keys

MON WIN CAM MON-G CAM-G

Select

a monitor Select a video tile

(decoders only) Select a camera Select a monitor

group Select a camera

group

MULT MAC TOUR GROUP SET

Select a multiview

display format

Call a macro Set or call a tour Set or call a

group .

Set preset tour,

shadow tour

PRESET CALL PATROL PATTERN AUX1

Set

a preset Call a preset Call a preset tour Call a shadow

tour AUX 1

SHIFT LOCK PREV NEXT AUX2

Shift

Lock screen Previous camera Next camera AUX 2

Locking the keypad

When in live view mode, press the LOCK key to lock the keypad and mouse. Once

locked, none of the keys (except LOCK), the joystick, the mouse, or the touch screen

can be used.

To lock the keypad in live view, press and hold the LOCK key, or press the SHIFT +

LOCK keys. When the keypad is locked, the LOCK key is lit red.

To unlock the keypad, press and hold the LOCK key, or press the SHIFT + LOCK keys.

The LOCK key turns blue.

The keypad automatically locks after a predetermined period of inactivity. The time (in

minutes) can be set in the Keypad > Hardware Settings menu.

Note: The keys are also locked when the screen is automatically locked.

Playback control dial and keys

See Figure 2 on page 6 for the location of playback control on the keypad.

8 TVK-800 User Manual

Figure 4: Description of the playback control dial and keys

Not used.

Play the last five minutes in

decoder playback mode.

Play/pause.

Stop play back. Play back the previous file (not

available in USB playback mode).

Record. Play back the next file (not

available in USB playback mode).

Select options on the LCD display

There are four ways to select and enter items on the LDC display:

•Touch pen: Use the touch pen (see Figure 1 on page 5) to select options on

screen. Replace the touch pen in its holder when finished using it.

•Finger: Use your finger to select options on screen.

•Joystick: Rotate the joystick to position the on-screen cursor in the desired location.

Press the center key on the joystick to select.

•Mouse: Use a mouse. Plug the mouse into the USB socket on the back of the

keypad.

Joystick operation

Move the joystick in one of eight directions to control pan/tilt. Rotate the knob for zoom

control.

Press the center key on the joystick for the Enter function and to capture snapshots.

Save the snapshots to a USB flash drive or to a FTP site.

Using the key commands

Key operation

Table 1: Operating a multiple video display

Key

Description Example

MON

Num+MON: Select the video output to

be controlled by the decoder, NVR, or

DVR.

Note: When Num=0, the system enters

local live view mode.

Press the 2+MON keys to select monitor

Table des matières

Autres manuels Interlogix Clavier

Interlogix

Interlogix NX-1815E Manuel utilisateur

Interlogix

Interlogix SuperBus 2000 2X16 Manuel utilisateur

Interlogix

Interlogix NX-1815E Manuel utilisateur

Interlogix

Interlogix NX1192E Manuel utilisateur

Interlogix

Interlogix NXG-183 Series Manuel utilisateur

Interlogix

Interlogix NX-182xx NetworX Fiche d'information produit

Interlogix

Interlogix NX-181 Series Manuel utilisateur

Interlogix

Interlogix ACL875SU Instructions de montage

Interlogix

Interlogix NX-4V2 Manuel utilisateur

Interlogix

Interlogix NetworX NX-6V2 Manuel utilisateur

Interlogix

Interlogix NX-181xx NetworX Manuel utilisateur

Interlogix

Interlogix NX1248 Manuel utilisateur

Interlogix

Interlogix ATS1151 Instructions de montage

Interlogix

Interlogix NXG-183 Series Instructions de montage

Interlogix

Interlogix NX-148E-RF Manuel utilisateur

Interlogix

Interlogix CADDX NX148-E Manuel utilisateur

Manuels Clavier populaires d'autres marques

BFT

BFT SELETTO Manuel utilisateur

Micro Id

Micro Id MP7G3BL Manuel d'instructions

WindowMaster

WindowMaster WLI 130 Manuel utilisateur

ACT

ACT ACT PRO 1030 Manuel utilisateur

Cardin

Cardin SSB Series Manuel utilisateur

Harman Kardon

Harman Kardon KP 1 Manuel utilisateur

Chamberlain

Chamberlain KPR2000 Guide de l'utilisateur

CYP

CYP CR-KP1 Manuel utilisateur

Aeware

Aeware k-35 Series Guide de référence

Aritech

Aritech CS-175 Series Manuel utilisateur

GE NetworX NX-1600E Series Manuel utilisateur

Lenze AC Tech

Lenze AC Tech MC SERIES Manuel utilisateur

Burg Wächter

Burg Wächter secuENTRY 7711 Manuel utilisateur

Aeware

Aeware in.k450 Manuel utilisateur

Lenze

Lenze EPM-H410 Manuel utilisateur

Toshiba

Toshiba RKP007Z Manuel utilisateur

Gemini

Gemini GEM-DXK1 KEYPAD Manuel utilisateur

Russound

Russound MDK-C5 Manuel d'utilisation