Inteno EG400 Manuel utilisateur
EG400
Ethernet/SFP WiFi Router
Installation Guide
2
CE Declaration of Conformity
For the following equipment: Ethernet/SFP WiFi Router
Product name: EG400
1.0
The following manufacturer is responsible
for this declaration:
Company name
Inteno Broadband Technology AB
Company adress
Stensätravägen 13
127 39 Skärholmen, Stockholm
Position/Title
CEO
Legal signature
Place Date
Sweden 05/06 2017
Hereby, Inteno Broadband Technology AB
declares that the radio equipment type
Ethernet/SFP WiFi Router is in compliance
with Directive 2014/53/EU. The full text of the
EU declaration of conformity is available at
the following internet address:
https://www.intenogroup.com/red/eg400
3
Language Page
English ..........4
Svenska .........8
Suomi..........12
Norsk ..........16
Dansk..........20
EG400 - Ethernet/SFP WiFi Router
Table of contents
4
EG400 - Ethernet/SFP WiFi Router
BROADBAND WIRELESS
TEL1/TEL2
USB 3.0USB 2.0
TEL1TEL2WANLAN4 LAN3 LAN2 LAN1
POWERON/OFF
Top
Back
The Top consist of both LEDs and touch buttons, see below.
BROADBAND WIRELESS
TEL1/TEL2
USB 3.0USB 2.0
TEL1TEL2WANLAN4 LAN3 LAN2 LAN1
POWERON/OFF
LED/TouchLED/TouchLED/Touch
English Svenska Suomi Norsk Dansk
5
EG400 - Ethernet/SFP WiFi Router
1. Start Box
Check that the following
items are in the Start Box:
• Inteno EG400
• Power adapter
• RJ45 Network cable (Red,
large connector)
• RJ45 Network cable (Yellow,
large connector)
• RJ11 Telephone cable (Green,
small connector)
2. Connecting the WAN/
broadband connection
– If the EG400 is not installed using the fiber tray.
Do as follows:
1. Shut down your computer.
2. Connect a RJ45 network cable between
your broadband outlet and the EG400
WAN port (WAN).
3. Connecting the LAN
1. Connect a RJ45 network cable between
the EG400 network port LAN1
and
the network port on the back or side
of your computer. If you have more
computers, use LAN2, LAN3 and
LAN4.
2. Plug the DC adapter into an electrical
socket and connect it to ”POWER” in
the back of the EG400.
3. Start the computer.
4. The colored lights on the EG400 panel
will start blinking. Please wait for 120
seconds for this process to complete.
5. If you have connected your gateway
properly, the Status, Broadband and
Internet lights will have a fixed color.
See picture labeled ”Top.” You have
now connected the EG400.
This guide will help you install the Inteno EG400. Your
service provider will supply you with information about log in
and access. EG400 can be connected to an Ethernet based
broadband network through the FTTH interface or through
the WAN port marked as RED.
Installation Guide
6
EG400 - Ethernet/SFP WiFi Router
4. Connecting the
Wireless Local
Area Network (WLAN)
1. Make sure that the ”4. Wireless”
button on the front panel is enabled
(lit). If not, press it so it gets lit.
2. For wireless connection first perform a
search for available wireless networks
using the WLAN client.
3. Compare the list with the “Network
Name” (SSID) which is shown on a
sticker underneath or on the side of
the EG400.
4. Connect by clicking on the corresponding
SSID and then provide the encryption
code, which is shown on the sticker
labeled ”WiFi Key” underneath or on
the side of the EG400.
5. Description of
the front LED
The front LED is managed by the software.
This is the default setup, but your operator
may have another setup.
Graphics on the front panel
1. Status
Green – power on
Red – boot failed
2. Broadband (WAN)
Off – no connection
Green – IP address ok
Red – no IP address
3. Internet
Green - connected to the internet
(DNS available)
Red - connection failed (no DNS
available)
BROADBAND WIRELESS
TEL1/TEL2
USB 3.0USB 2.0
TEL1TEL2WANLAN4 LAN3 LAN2 LAN1
POWERON/OFF
LED/TouchLED/TouchLED/Touch
English Svenska Suomi Norsk Dansk
EG400 - Ethernet/SFP WiFi Router
7
4. Wireless (Wi-Fi)
Green – wireless network 2.4 GHz active
Blue – wireless network 5 GHz active
5. Ethernet
Indicaton for LAN1 - LAN4
Green - cable connected and online
Off - no cable connected or offline
6. WPS
Press and hold for more than 3
seconds to start WPS function
Green (blinking) – WPS function
in progress
7. Tel 1/Tel 2
Off – no voice device
Green – Voice device registered and ok
Green (blinking) – Voice enabled but not ok
8. DECT
Press and hold for more than 3
seconds to start DECT pairing
Off – no DECT device
Green – DECT device connected
Green (blinking) – DECT pairing on-going.
EXT
Off – No external device
Green – external device detected
Green (blinking) – device detected with
alarm status (your operator may have
another setup)
6. Troubleshooting
1. Check that the power is on.
The Status indicator LED should be lit.
See picture labeled “Top”.
2. Is the Status indicator light off?
Check that the modem is properly
connected to the power adapter.
Check that the power adapter is
connected to an electrical outlet.
Check the ON/OFF switch - it should
be set to ”1”. If the modem is properly
connected and switched to on, a
power indicator light that is still not
on may indicate a faulty modem or a
faulty power adapter. Contact your
service provider.
3. Are the Status and Internet
indicator lights red? Contact your
service provider.
4. Is the WAN (Broadband) indicator
light off? Check the connection of
WAN port. If EG400 is installed with
fiber tray contact service provider. If
the Broadband indicator light is off,
despite proper connection, contact
your service provider.
5. Is the Ethernet indicator light off?
Check the connection between the
LAN port on the modem and the
network port on the back or side of
your computer. Check that the NIC in
your computer is functioning properly.
6. Reset button. See picture labeled
“Back.” This button resets the modem
to factory
settings. Hold it for more
than 10 seconds.
8
EG400 - Ethernet/SFP WiFi Router
BROADBAND WIRELESS
TEL1/TEL2
USB 3.0USB 2.0
TEL1TEL2WANLAN4 LAN3 LAN2 LAN1
POWERON/OFF
Ovansida
Baksida
Vissa lysdioder är tryckknappar.
BROADBAND WIRELESS
TEL1/TEL2
USB 3.0USB 2.0
TEL1TEL2WANLAN4 LAN3 LAN2 LAN1
POWERON/OFF
TryckTryckTryck
9
English Svenska Suomi Norsk Dansk
EG400 - Ethernet/SFP WiFi Router
1. Startboxen
Kontrollera att följande finns
med i startboxen:
• Inteno EG400
• DC-adapter (strömadapter)
• RJ45 Nätverkskabel (röd, stor kontakt)
• RJ45 Nätverkskabel (gul, stor kontakt)
• RJ11 Telefonkabel (grön, liten kontakt)
2. Inkoppling WAN/
Bredbandsuttag
Gör så här:
1. Stäng av din dator.
2. Koppla en RJ45 nätverkskabel
mellan ditt bredbandsuttag och
EG400 WAN-kontakt märkt WAN.
3. Inkoppling LAN
1. Koppla en RJ45 nätverkskabel mellan
EG400 nätverkskontakt LAN1 och
nätverkskontakten på baksidan eller
sidan av din dator. Finns fler datorer
än en, används därefter LAN2, LAN3
samt LAN4.
2. Ta fram DC-adaptern, anslut den till
eluttaget och sätt den runda kontakten
i uttaget märkt ”Power”.
3. Starta datorn.
4. De färgade lamporna på EG400-
panelen kommer att börja blinka.
5. Var god vänta i cirka 120 sekunder
medan den här processen slutförs.
Har du gjort allting rätt så kommer
lamporna Status, Broadband och
Internet lysa med fast sken på ditt
modem, se bild ”Ovansida”. Du är nu
färdig med inkopplingen av EG400.
Den här installationsguiden hjälper dig att installera Inteno
EG400. Information om hur du loggar in och får åtkomst till
dina tjänster får du från din operatör. EG400 kan anslutas till
ett Ethernet-baserat bredbandsnät genom FTTH-interface,
eller genom WAN-porten (den röda).
Installationsguide
10
EG400 - Ethernet/SFP WiFi Router
4. Inkoppling av trådlös
data-anslutning (WLAN)
1. Se till att ”4. Wireless” på frontpanelen
är tänd och lyser.
2. För trådlös dataanslutning, gör först en
sökning efter trådlösa nätverk på din
dator.
3. Jämför i listan med det ”nätverksnamn”
(SSID) som anges
på klisterlappen på
undersidan eller sidan av EG400.
4. Anslut genom att dubbelklicka på rätt
nätverksnamn (SSID) och därefter
skriva in den krypteringsnyckel som
anges på klisterlappen märkt “WiFi-Key”
på undersidan eller sidan av EG400.
5. Beskrivning
av frontpanelen
Frontpanelens LED är hanterad av
mjukvaran. Följande är standard, men din
operatör kan ha en annan uppställning
Grafik på frontpanel:
1. Status
Grön – strömmen är på
Röd – uppstartsfel
2. Broadband (WAN)
Släckt – ingen anslutning
Grön – IP-adress ok
Röd – ingen IP-adress
3. Internet
Grön – ansluten till internet (DNS tillgänglig)
Röd – internetanslutning misslyckades
(ingen DNS tillgänglig)
BROADBAND WIRELESS
TEL1/TEL2
USB 3.0USB 2.0
TEL1TEL2WANLAN4 LAN3 LAN2 LAN1
POWERON/OFF
TryckTryckTryck
Table des matières
Langues :
Autres manuels Inteno Routeur sans fil
