Intelligent Building Solutions CAP 2020 DR H Manuel utilisateur

Installation Manual

CAP 2020 DR H

ACCESS CONTROL UNIT

(for hotel anage ent syste s)

●Proxi ity card based

●DIN-rail ounting

CIB-tech

I n t r o d u c t i o n

The CAP 2020 DR H is a proximity card based access control device, with hotel room economizer unction,

part o the CIB-tech automation system.

The unit can control the entry in a hotel room. It accepts up to 1024 users and provides entry via the use o

proximity cards. It can control the power supplied to the room, based on the state o the room's proximity

card holder.

Additional Equip ent Required

1. Functional CIB-tech syste

A minimal number o essential CIB-tech components to make a unctional CIB-tech system1.

2. Proxi ity card and/or PIN code reader with bell button, for entry request

A proximity card reader with a 26-bit Wiegand-type output, urther re erred to as “Reader A”2.

NOTE: The proximity card reader must supply the bell button event in Wiegand data ormat.

3. Proxi ity card holder

Proximity card holder with built in proximity card reader (ex IBS product RFE 10 F), or any simple,

contact based card holder with voltage ree contacts2, urther re erred to as “Smart card holder” or

“Simple card holder”.

4. Open door sensor (optional)

Normally open or normally closed type with voltage ree contacts2.

5. Electric door lock

Fail sa e (power to lock) or ail secure (power to open) strike lock/door bolt/magnetic lock2.

6. Power supply for electric door lock

Re er to the electric door lock's characteristics to choose a suitable power supply. A power supply

with battery backup is recommended.

7. Circuit breaker

Miniature circuit breaker (MCB) or DIN-Rail mountable use must be used or over-current protection.

T e c h n i c a l S p e c i f i c a t i o n s

Electrical characteristics

●Power Supply

The CAP 2020 DR H unctions as a node in a CIB-tech system, being powered rom the CIB-tech

system's power supply via the CIB-tech connectors.

○Operating voltage range: 20 to 28V DC (nominal 24V DC)

○Supply current

■Standby current (without reader/card holder): 22mA

■Maximum current (without reader/card holder): 50mA

■Typical standby current (with reader and card holder): 110mA

■Absolute maximum current (with reader and card holder): 300mA

●Power output

The CAP 2020 DR H can provide power to the proximity card reader and card holder.

○Output voltage: 12V DC

1 See “CIB-tech installation manual” for details.

2 See “Recommended equipment to be used with CIB-tech” for details

○Maximum output current: 2 x 170mA

●Relay output (for electric door lock)

I an electric door lock with a DC power supply is used, an external suppressor diode must be used3.

○Rated voltage: 24V AC/DC

○Rated current: 2A

●Relay output (for roo power)

○Rated AC voltage: 250V AC

○Rated current: 16A

●Signal Input

○Wiegand data input:

■supported input voltage levels: 0 - 5V

■input impedance: 1KOhm

○Open door sensor: N.O. or N.C. with voltage ree contacts

○Contact based card holder: N.O. with voltage ree contacts

●Signal Output

○External LED control:

■output voltage levels: 0 - 5V

■output current: 15mA

Mechanical characteristics

The CAP 2020 DR H has a standard 3-module wide enclosure or M36 type DIN-Rail

●Dimensions: 96mm W x 52mm L x 60mm D

●Weight: 130g

Environ ental characteristics

●Operating temperature: 0ºC to 65ºC

●Storage temperature: -10ºC to 70ºC

K e y F e a t u r e s

●Programmable via the CIB-tech system with dedicated so tware

●Controls unidirectional access through one door

●Provides access or up to 1024 users

●Users may be members o one o up to 30 groups with di erent access rights, based on a weekly

schedule. Groups have individual access right expiration dates

●Controls the power supply or one hotel room.

●Room power is automatically enabled when a valid entry request is detected.

●Programmable “keep room power on” time, a ter card is removed rom the card holder.

●Support or Simple card holder (any card may be placed in the holder and the room will be powered

on) and Smart card holder (the room will be powered on only i a valid proximity card is placed in the

RFE 10 F).

●Support or an open-door sensor input or detecting actual door openings.

●Internal battery powered real-time clock. Clock keeps running in case o power ailure

●Internally stored 1024-entry access log with time stamps

●Internally stored 1024-entry open door event log with time stamps

IBS product PS 121 D is a dedicated power supply for door locks: 12V AC and DC output, internal suppressor

diode. Note that battery backup for door lock is not possible with it.

Please verify whether it is suitable for your door lock!

●Con igurable relay output; normal-open or normal-closed (in power-o state relay contacts are

always open)

●Two unctional modes: open door momentarily or toggle door state

●Con igurable keep-door-open time or the momentary-open mode

●Relay outputs are remotely controllable via the CIB-tech system

●Internal bi-color LED indicating the state o the door lock (green: closed / red: open)

●Support or two external LEDs ( or reader A and and card holder) indicating a valid proximity card;

I n s t a l l a t i o n

The CAP 2020 DR H is meant to be installed on a standard M36 type DIN-Rail.

Part description

●Bus connectors:

○4P4C modular jack connectors or CIB-tech connection1

●Sys button:

○pushbutton or CIB-tech system con iguration

●EOL ju per:

○CIB-tech system's End O Line jumper1

●LED:

○indicator LED or door lock state (green : closed / red : open)

●DIN-rail release:

○lever or removing the device rom the M36 DIN-Rail

●Low ter inal block: terminals or connecting external devices

1. Smart card holder – LED control

2. Smart card holder – Wiegand data 1

3. Smart card holder – Wiegand data 0 / Simple card holder N.O. contact

4. Smart card holder – DC power supply +12V

5. Smart card holder – DC power supply ground / Simple card holder common contact

6. Reader A – LED control;

7. Reader A – Wiegand data 1

8. Reader A – Wiegand data 0

9. Reader A – DC power supply +12V

10. Reader A – DC power supply ground

11. Open-door sensor input

12. Relay contact 1 or electronic door lock

13. Relay contact 2 or electronic door lock

●High ter inal block: terminals or connecting external door bell

H5. Relay contact 1 or room power

H6. Relay contact 2 or room power

1 See “CIB-tech installation manual” for details.

Wiring diagra s

Connection to CIB-tech syste :

Use the CAP 2020 DR H device's two 4P4C modular jack connectors to connect it to the CIB-tech systems

(chain like) bus. Do not orget to remove the EOL jumper i the device is not the last element o the chain1

1 See “CIB-tech installation manual” for details.

0v DC

24v DC

BUS-L

BUS-H

0v DC

24v DC

BUS-L

BUS-H

Sys button

EOL jumper

Bus connectors

CAP 2020 DR H

LED

Bus connectors

EOL jumper

Low terminal block

Din-rail release lever

1 1312111098765432

Sys button

H6H3 H4H2H1 H5 H7 H8 H9

High terminal block

1 1312111098765432

Low terminal block

High terminal block

H6H3 H4H2H1 H5 H7 H8 H9

Connecting the input devices

Connection example or proximity card reader and Smart card holder:

Connection example or proximity card reader and Simple card holder:

CAP 2020 DR H

LED

+12V

GND

Reader A

LED

+12V

GND

Smart

card

holder

Open door sensor

(optional)

CAP 2020 DR H

LED

+12V

GND

Reader A

Open door sensor

(optional)

Simple

card

holder

Common N.O.

NOTE: Some proximity card readers don't have a LED control input. For these readers the LED control

output o the CAP 2020 DR H is not connected.

Some proximity card readers have auxiliary inputs and outputs (ex. tamper, auxiliary led). These auxiliary

inputs and outputs can not be connected to the CAP 2020 DR H.

Connecting the electronic door lock

Connection example or AC-type electronic door lock:

Connection example or DC-type electronic door lock:

NOTE: An external suppressor diode (ex. 1N4001) is required.

CAP 2020 DR H

Electronic door lock

( ail sa e or ail secure)

type 12/24V AC

Line

transfor er

12/24V AC 230V AC

CAP 2020 DR H

Electronic door lock

( ail sa e or ail secure)

type 12/24V DC

DC power

supply

12/24V DC 230V AC

Suppressor diode

Connection example or DC-type electronic door lock and PS1213D, dedicated power supply :

CAP 2020 DR H

Electronic door lock

( ail sa e or ail secure)

type 12V DC

230V AC

PS 1213 D

1 765432

8 14131211109

- +

Connecting the roo power control

NOTE: A max. 16A Miniature Circuit Breaker (MCB) or max. 16A use must be connected in series with the

CAP 2020 DR H's room power relay.

Document Version 1.0

Technical Support:

http://www.ibs-smarthouse.com/

in [email protected]

All trademarks used in this document are properties o their respective owners.

The manu acturer reserves the right to change the technical eatures o this product without prior notice.

CAP 2020 DR H

230V AC

MCB

16A

230V~

N L

Room equipment

and connectors

Table des matières

Autres manuels Intelligent Building Solutions Contrôleurs d'accès IP

Intelligent Building Solutions

Intelligent Building Solutions CAP 2020 DR IB Manuel utilisateur

Manuels Contrôleurs d'accès IP populaires d'autres marques

ZKTeco

ZKTeco SpeedFace-V5L Manuel utilisateur

Jantar

Jantar REX A-1-9 Manuel utilisateur

2N Access Unit Feuille d'instructions

Kedacom

Kedacom KSCA120 Series Manuel utilisateur

H3C

H3C WX2880X Manuel utilisateur

G4S

G4S S870-EX Mode d’emploi

PRASTEL

PRASTEL M2000PE Manuel utilisateur

Allegion

Allegion interflex IF-281 Cylinder Manuel utilisateur

TECOM

TECOM TS1067E Manuel utilisateur

Fermax

Fermax Memokey 100C Guide de l'utilisateur

Fermax

Fermax CITYLINE MEMOKEY Mode d’emploi

Software House

Software House iSTAR Pro 2U RM Mode d’emploi

AKCP

AKCP SP+ Manuel utilisateur

Bpt

Bpt HNA/102 Manuel utilisateur

Civintec

Civintec CV9601T-T-1F Manuel utilisateur

BioMax

BioMax N-X90W Manuel utilisateur

ZKTeco

ZKTeco OP-200 Manuel utilisateur

FingerTec

FingerTec s-Kadex Manuel utilisateur