Intel NUC8 Home Manuel utilisateur

User Guide for NUC8i7BEHGA, NUC8i5BEHFA and NUC8i3BEHFA

Intel® NUC8 Enthusiast, a Mini PC with Windows® 10 –NUC8i7BEHGA

Intel® NUC8 Home, a Mini PC with Windows® 10 –NUC8i5BEHFA

Intel® NUC8 Home, a Mini PC with Windows® 10 –NUC8i3BEHFA

User Guide

User Guide for NUC8i7BEHGA, NUC8i5BEHFA and NUC8i3BEHFA

Before You Begin

CAUTIONS

The steps in this guide assume you’re familiar with computer terminology and with the

safety practices and regulatory compliance required for using and modifying computer

equipment.

Disconnect the computer from its power source and from any network before performing any of

the steps described in this guide.

Failure to disconnect power or networks before you open the computer or perform any procedures

can result in personal injury and/or equipment damage. Some circuitry on the board can continue

to operate even though the front panel power button is off.

Follow these guidelines before you begin:

Always follow the steps in each procedure in the correct order.

Create a log to record information about your computer, such as model, serial

numbers, installed options, and configuration information.

Electrostatic discharge (ESD) can damage components. Perform the procedures

described in this chapter only at an ESD workstation using an antistatic wrist strap and a

conductive foam pad. If such a station isn’t available, you can provide some ESD

protection by wearing an antistatic wrist strap and attaching it to a metal part of the

computer chassis.

Installation Precautions

When you install and test the Intel NUC, observe all warnings and cautions in the installation

instructions.

To avoid injury, be careful of:

Sharp pins on connectors

Sharp pins on circuit boards

Rough edges and sharp corners on the chassis

Hot components (such as SSDs, processors, voltage regulators, and heat sinks)

Damage to wires that could cause a short circuit

Observe Safety and Regulatory Requirements

If you don’t follow these instructions, you increase your safety risk and the possibility of

noncompliance with regional laws and regulations.

User Guide for NUC8i7BEHGA, NUC8i5BEHFA and NUC8i3BEHFA

This guide tells you how to:

•

Upgrade memory (RAM)

•

Change/install an M.2 SSD

•

Change/install a 2.5-inch drive

•

Use a VESA mount bracket

•

Connect power

•

Set up Microsoft® Windows® 10

•

Install the latest device drivers and software

•

Recover the operating system

Open the Chassis

Unscrew the four corner screws on the bottom of the chassis and lift the cover.

Upgrade System Memory

The Intel NUC Mini PC NUC8i7BEHGA have two 260-pin DDR4 SO-DIMM sockets, pre-

installed with one 8GB DDR4 2400 MHz SO-DIMM.

The Intel NUC Mini PC NUC8i5BEHFA and NUC8i3BEHFA have two 260-pin DDR4 SO-

DIMM sockets, pre-installed with one 4GB DDR4 2400 MHz SO-DIMM.

To upgrade memory, be sure to select memory modules that meet these requirements:

1.2V low voltage memory

2400 MHz SO-DIMMs

Non-ECC

User Guide for NUC8i7BEHGA, NUC8i5BEHFA and NUC8i3BEHFA

Find compatible memory modules in the Intel® Product Compatibility Tool.

NUC8i7BEHGA

NUC8i5BEHFA

NUC8i3BEHFA

NOTE

If you plan to install only one memory module, install it in the lower memory

socket.

To upgrade or add memory, follow these steps:

1. Observe the precautions in "Before You Begin" on page 2.

2. Turn off all peripheral devices connected to the computer. Turn off the computer and

disconnect the power cord.

3. Remove the computer’s bottom chassis cover.

Upgrade to different memory

a. Remove the pre-installed memory module

i. Gently spread the retaining clips at each end of the memory socket, which

causes the module to pop out of the socket (C).

ii. Holding the module by the edges, lift it away from the socket, and

store it in an anti-static package.

b. Install the new memory module

i. Align the small space at the bottom edge of the memory module with

the key in the socket.

ii. Insert the bottom edge of the module at a 45 degree angle into the

socket (A).

iii. When the module is inserted, push down on the outer edges of the

module until the retaining clips snap into place (B). Make sure the

clips are firmly in place (C).

Install an additional memory module

a. Align the small space at the bottom edge of the memory module with the key on the

socket.

b. Insert the bottom edge of the module at a 45 degree angle into the socket (A).

c. When the module is inserted, push down on the outer edges of the module

until the retaining clips snap into place (B). Make sure the clips are firmly in

User Guide for NUC8i7BEHGA, NUC8i5BEHFA and NUC8i3BEHFA

place (C).

4. Reinstall and reconnect any parts you removed or disconnected to reach the memory

sockets.

5. Replace the computer’s cover and reconnect the power cord.

Changing an M.2 SSD or Intel® Optane™ Memory Module

The Intel NUC Mini PC NUC8i7BEHGA support an 80mm or 42mm m.2 SSD, preinstalled

with one 32GB Intel Optane Memory.

The Intel NUC Mini PC NUC8i5BEHFA and NUC8i3BEHFA support an 80mm or 42mm m.2,

preinstalled with one 16GB Intel Optane Memory.

Find compatible M.2 SSDs in the Intel® Product Compatibility Tool.

NUC8i7BEHGA

NUC8i5BEHFA

NUC8i3BEHFA

NOTE

Before changing the Intel Optane memory module, it needs to be disabled. Follow

Removing Intel Optane Memory on this page first, before taking the module out.

To Change an M.2 SSD:

1. Remove the small silver screw from the 80mm or 42mm metal standoff on the board (A).

2. Remove the pre-installed SSD/Intel Optane Memory from the connector.

3. Align the space at the bottom of the new M.2 SSD to the key on the connector.

4. Insert the bottom edge of the M.2 SSD into the connector (B).

5. Secure the card to the standoff with the small silver screw (C).

User Guide for NUC8i7BEHGA, NUC8i5BEHFA and NUC8i3BEHFA

Changing a 2.5” SSD or Hard Drive

The Intel NUC Mini PC NUC8i7BEHGA support an additional 2.5” Solid State Drive (SSD) or

Hard Disk Drive (HDD), pre-installed with one 2TB HDD.

The Intel NUC Mini PC NUC8i5BEHFA and NUC8i3BEHFA support an additional 2.5” Solid

State Drive (SSD) or Hard Disk Drive (HDD), pre-installed with one 1TB HDD.

Find compatible 2.5” drives in the Intel Product Compatibility Tool.

NUC8i7BEHGA

NUC8i5BEHFA

NUC8i3BEHFA

1. Unscrew the four screws holding the current drive in the bay.

2. Remove the pre-installed drive from the drive bay.

3. Slide the new 2.5” drive into the drive bay, ensuring the SATA connectors are fully seated into

the connectors of the SATA daughter card (A).

User Guide for NUC8i7BEHGA, NUC8i5BEHFA and NUC8i3BEHFA

4. Secure the drive into the drive bay with the four screws that were used in step 1. Set the drive

bay bracket down inside the chassis (C).

Close the Chassis

After all components have been installed, close the Intel NUC chassis. Intel recommends this be

done by hand with a screwdriver to avoid over-tightening and possibly damaging the screws.

Attach and Use the VESA Bracket (Optional)

Follow these instructions to attach and use the VESA mount bracket:

User Guide for NUC8i7BEHGA, NUC8i5BEHFA and NUC8i3BEHFA

1. Using the four small black screws that were included in the box, attach the VESA bracket to

the back of the monitor or TV.

2. Attach the two slightly larger black screws to the bottom chassis cover of the Intel NUC.

3. Slide the Intel NUC onto the VESA mount bracket.

User Guide for NUC8i7BEHGA, NUC8i5BEHFA and NUC8i3BEHFA

Connect Power

Each Intel NUC model includes either a region-specific AC power cord or no AC power cord (only the

power adapter).

Product codes

Power cord type

BOXNUC8i7BEHGA

BOXNUC8i5BEHFA

BOXNUC8i3BEHFA

No power cord included. An AC power cord needs to be purchased

separately. Power cords are available at many Internet sites for use in

multiple countries. The connector on the power adapter is a C5 type

connector.

BOXNUC8i7BEHGA1

BOXNUC8i5BEHFA1

BOXNUC8i3BEHFA1

US power cord included.

BOXNUC8i7BEHGA2

BOXNUC8i5BEHFA2

BOXNUC8i3BEHFA2

EU power cord included.

BOXNUC8i7BEHGA3

BOXNUC8i5BEHFA3

BOXNUC8i3BEHFA3

UK power cord included.

BOXNUC8i7BEHGA4

BOXNUC8i5BEHFA4

BOXNUC8i3BEHFA4

Australia/New Zealand power cord included.

Connect AC power.

User Guide for NUC8i7BEHGA, NUC8i5BEHFA and NUC8i3BEHFA

Set Up Microsoft® Windows® 10

Microsoft Windows 10 is already installed on the Intel NUC. The first time you start the computer,

you are guided through the Windows 10 setup steps, including:

Selecting your region and language.

Accepting the Microsoft Windows license terms.

Personalizing Windows and assign a PC Name.

"Get Online" dialog to pick a wireless network (this step is optional).

Choosing Express Settings or Customize.

Assigning a User Name and Password.

Reinstalling the Operating System

If you upgrade or replace the computer’s drive, you may need to install a new version of the

operating system. See these resources:

Supported Operating Systems

Windows Setup Guide

Install the Latest Device Drivers and Software

Here are the options for keeping device drivers current:

Allow the Intel® Driver & Support Assistant (Intel® DSA) to detect out-of-date drivers

Manually download drivers, BIOS, and software from Download Center.

NUC8i7BEHGA

NUC8i5BEHFA

NUC8i3BEHFA

The following device drivers and software are available.

Bluetooth

Chipset

CIR (Infrared)

Graphics

Intel® ME

Intel® Rapid Storage Technology

Intel® Ready Mode Technology

Intel® Software Guard Extensions (Intel® SGX)

LAN (wired and wireless)

Realtek Audio

Realtek Card Reader

Serial IO

Thunderbolt

Operating System Recovery

There’s a Windows recovery partition on the Intel NUC. You can use this partition to Refresh, Reset,

or Restore Windows. Here is what each of these actions do:

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Intel Ordinateur de bureau

Intel

Intel SC5650SCWS Manuel utilisateur

Intel

Intel LP300 Manuel utilisateur

Intel

Intel NUC Series Manuel utilisateur

Intel

Intel PC On A Stick Manuel utilisateur

Intel

Intel NUC7CJYS Guide de configuration rapide

Intel

Intel NUC6i3SYK Manuel utilisateur

Intel

Intel System 310 Manuel du propriétaire

Intel

Intel NUC 8 Enthusiast Manuel utilisateur

Intel

Intel NUC5i3RYK Manuel utilisateur

Intel

Intel NUC8i7HNK Manuel utilisateur

Intel

Intel SRSH4 - Server Platform - 0 MB RAM Manuel utilisateur

Intel

Intel NUC7 Home Manuel utilisateur

Intel

Intel SR6850HW4 - Server Platform - 0 MB RAM Manuel utilisateur

Intel

Intel Compute Stick STCK1A8LFC Manuel utilisateur

Intel

Intel NUC6i3SYH Manuel utilisateur

Intel

Intel NUC 13 Pro NUC13ANHi7 Manuel utilisateur

Intel

Intel NUC7i3BNHXF Manuel utilisateur

Intel

Intel NUC8i7HVKVAW Manuel utilisateur

Intel

Intel NUC 7 HOME Manuel utilisateur

Intel

Intel NUC8i3BEK Manuel utilisateur

Intel

Intel Compute Stick STK1A32SC Manuel utilisateur

Intel

Intel NUC 13 Pro Mini PC NUC13ANKi7 Manuel utilisateur

Intel

Intel SR1530AH - Server System - 0 MB RAM Manuel utilisateur

Intel

Intel NUC 12 Pro X Manuel utilisateur

Manuels Ordinateur de bureau populaires d'autres marques

HP m9060n - Pavilion - Elite Fiche technique

Asus

Asus E210 Series Manuel utilisateur

Dell

Dell Inspiron 600m Manuel utilisateur

Dell

Dell Inspiron 3662 Manuel utilisateur

TotalFlow

TotalFlow uFLO Manuel utilisateur

HP Presario SV7000 - Desktop PC Manuel utilisateur

HP ProDesk 400 G5 Manuel

Logitech

Logitech MK320 Manuel utilisateur

Dell

Dell XPS 730 H2C Manuel utilisateur

Sony

Sony Vaio Series Manuel utilisateur

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuel utilisateur

Alto

Alto MD 250 Manuel utilisateur

Lenovo

Lenovo ThinkCentre Edge 72 Manuel

Lenovo

Lenovo ThinkStation D20 Manuel

Arbor Technology

Arbor Technology FPC-7800 Series Manuel utilisateur

Sony

Sony VAIO VGX-TP1 Series Manuel utilisateur

Asus

Asus Eee Box B204 Manuel utilisateur

Dell

Dell Optiplex 9010 All In One Manuel utilisateur