INSTEON TempLinc 2441TH Manuel utilisateur

Page 1 of 32 Rev: 10/13/2015 9:13 AM

Insteon®Thermostat

Owner’s Manual (#2441TH, 2732-422, 2732-522, 2732-242,

2732-442, 2732-542)

Page 2 of 32 Rev: 10/13/2015 9:13 AM

About Insteon Thermostat 3

Insteon Thermostat – Features and Benefits 3

What’s in the Box? 3

Insteon Thermostat Button Overview 4

Insteon Thermostat Operation and Programming 5

Mode Button Operation 5

Energy Button Operation 6

Set Button Operation 7

Time/Sensor Button Operations 7

Program Button Operation 8

Fan and Hold Button Operations 10

Master Button Operation 10

Installation 11

Tools Needed 11

Installation 11

Wire Connections 12

Test Operation 15

Adding an Insteon Wireless Thermostat 15

Insteon Programming 17

Add Insteon Thermostat as an Insteon Controller 17

Removing Insteon Thermostat as an Insteon Controller 19

Add Insteon Thermostat as an Insteon Responder 20

Remove Insteon Thermostat as an Insteon Responder 20

User Setup Mode Overview 22

User Setup Mode 22

Temperature and Humidity Calibration Mode 24

Advanced 2-Stage Heating or Cooling Systems 25

Factory Reset 25

Specifications 26

Troubleshooting 28

DECLARATION OF CONFORMITY 30

Certification and Warranty 32

Limited Warranty 32

Limitations 32

Page 3 of 32 Rev: 10/13/2015 9:13 AM

About Insteon Thermostat

Insteon Thermostat is a 7-day programmable Insteon-compatible thermostat. Insteon Thermostat

includes a humidity sensor and 2-stage heating plus 2-stage cooling capabilities.

Expand the system by creating extra temperature zones in your home. Simply add one or more Insteon

Wireless Thermostats as accessories to your system. Additionally, a Waterproof Temperature Sensor can

be added and extended up to 100 feet for remote temperature sensing.

Insteon Thermostat – Features and Benefits

•Installs and joins scenes with other Insteon devices in minutes

•Saves energy and money by remotely controlling and automating your home’s heating and AC

•Communicates wirelessly over radio frequency (RF)

•Can automatically remotely control Insteon devices when Insteon Thermostat reaches a specified

temperature or humidity level or switches to A/C or heat

•Reports changes in thermostat modes, temperature, humidity, setpoints and fan to compatible

automation controllers or software

•Fine-tunes thermostat setpoints by single degrees from any Insteon controller with specific Up

and Down buttons

•Stores setup state in memory so settings aren’t lost during power outages

•Two-year warranty

•Controllable via the web and smartphone app (iOS/Android/Windows Phone) using Insteon Hub

What’s in the Box?

•Insteon Thermostat

•Two mounting screws

•Two anchors

•Quick Start Guide

•Wire ID label stickers

Page 4 of 32 Rev: 10/13/2015 9:13 AM

Insteon Thermostat Sample

The gray buttons

are under the

Insteon

Thermostat door

Cool setpoint

Heat setpoint

Time of day

state

Humidity level

Time

Current

temperature

Temperature of remote

sensors or zone thermostats

position 1 and position 2

(up to 2)

Current

thermostat

mode:

Off, Auto,

Heat or Cool

Insteon Thermostat Button Overview

1) Up/Down buttons adjust the temperature setpoint based on the current mode.

2) Mode allows the user to select the current operational mode of the HVAC system. It cycles

among Off, Heat, Cool, Auto and Time of Day.

3) Energy (Leaf) button is designed as a quick access option that saves energy (and money). When

pressed, it will set back the setpoint by a specified value. The default value is 4° from the current

setting. To change the default offset value you must use software such as HouseLincTM.

4) Hold overrides a preprogrammed mode to stay in the current settings mode.

5) Fan cycles between Auto and Always On – there is no indicator for Auto Fan.

6) Master makes this device the master temperature controller when you have one or more zone

thermostats. Pressing and holding “Master” does not alter any scene or screen settings; it just

defines this Insteon Thermostat as the master temperature controller.

7) Time/Sensor allows you to set the day and time. It cycles among hour, minute, day and time

programming.

8) Program allows you to set up the various preprogrammed modes (Wake, Leave, Return and

Sleep). It also allows you to setup various features and calibrate the temperature and humidity.

9) Set is for adding and removing Insteon Thermostat to and from Insteon scenes. It functions like

the Set button on other Insteon devices.

Page 5 of 32 Rev: 10/13/2015 9:13 AM

Insteon Thermostat Operation and Programming

Mode Button Operation

Off Mode:

•No setpoints are shown.

•Up/Down arrows do not do anything.

Heat Mode:

•Only Heat setpoint is shown.

•Up/Down arrows change Heat setpoint.

Cool Mode:

•Only Cool setpoint is shown.

•Up/Down arrows change Cool setpoint.

Auto Mode:

•Both Cool and Heat setpoints are

shown.

•Up/Down arrows increase or decrease

values by the same amount.

Time of Day Mode:

•The program mode is active as indicated by

the return annotation.

•The Time of Day annotation is not

displayed in the other four modes (Off,

Heat, Cool or Auto).

•Both Cool and Heat setpoints are shown.

•Up/Down arrows increase or decrease

values by the same amount.

•When the thermostat moves to the next

time period, the setpoints will be adjusted

accordingly.

Note:

•To adjust the gap between the setpoints in Auto mode, press Mode to select Heat and set the

temperature you desire. Press Mode to select Cool and set the temperature you desire.

Press Mode to return to Auto; the settings will reflect your changes.

•If you set Heat and Cool to the same temperature, Heat will automatically move down 2° (the

minimum allowable gap).

Page 6 of 32 Rev: 10/13/2015 9:13 AM

Energy Button Operation

The Energy button is designed to be a quick, efficient energy-saving option. When you press the Energy

(leaf) button, Insteon Thermostat will adjust the Heat and Cool setpoints by a specified value. The default

value is 4° from the current setting. The default value can be changed via software such as HouseLinc.

•When you exit Energy mode, it will revert back the 4° that was changed upon entry.

•The unit remains in Energy mode until the Energy button is pressed again.

•Up/Down arrows adjust the temperature setpoint based on the mode you are in.

From Off Mode:

•Energy button does nothing because the

system is off (at maximum energy savings

already).

•When “Energy” appears on the screen for

Auto, Cool and Heat Modes, the 4° setback

is engaged.

From Heat Mode:

•Heat setback as specified.

•Default setback is 4° less.

•Notice that “Heating” is active on the left,

but not on the right since the setpoint is

lower that the actual temperature; the

element reads “Heat.”

From Cool Mode:

•Cool setback as specified.

•Default setback is 4° more.

From Auto Mode:

•Both Heat and Cool setpoints changed as

specified.

•Default setback is 4° more for Cooling and

4° less for Heating.

•Notice that “Heating” is active on the left,

but not on the right since the setpoint is

lower that the actual temperature; the

element reads “Heat.”

Page 7 of 32 Rev: 10/13/2015 9:13 AM

From Time of Day Mode:

•Both Heat and Cool setpoints changed as

specified.

•Default setback is 4°.

•Notice that “Heating” is active on the left, but

not on the right since the setpoint is lower

than the current temperature; the element

reads “Heat.”

Note: Onscreen text displaying “Heat” changes to “Heating” and “Cool” changes to “Cooling” to indicate

HVAC system is active. The status LED, if enabled, under the door also indicates current active state:

Cooling = green, Heating = red. At time of activation either Heating or Cooling text will blink for 3 seconds

then remain steady during the active cycle.

Set Button Operation

The Set button adds and removes Insteon Thermostat from Insteon scenes. It functions like the Set

button on other Insteon devices.

Time/Sensor Button Operations

•The Time/Sensor button allows the user to set the current day and time.

•It cycles among hour, minute, day and 12/24-hour format.

•Up/Down arrows cycle through the available options.

•Go to the next Time/Sensor step by pressing Time/Sensor button again.

•Exit Time/Sensor setup by:

- Timing out (4 minutes)

- Pressing Mode button

Note: Colored elements indicate LCD element that should be blinking during setting procedure.

First press of Time/Sensor:

Hours settings

•Up/Down arrows cycle through time in 1-hour

increments.

•Pressing and holding Up/Down arrows cycles

through faster.

Note: AM/PM changes automatically as needed.

Second press of Time/Sensor:

Minutes settings

•Up/Down arrows cycle through time in 1-

minute increments.

•Pressing and holding Up/Down arrows

cycles through faster.

Page 8 of 32 Rev: 10/13/2015 9:13 AM

Third press of Time/Sensor:

Day settings

•Up/Down arrows cycle through each day of the week as shown.

Fourth press of Time/Sensor:

Clock Format setting (12- or 24-Hour clock)

•Entire “time” blinks.

•Up/Down arrows cycle between 12- and 24-hour clock format.

Note: AM/PM is not displayed when in 24-Hour format.

Press Time/Sensor a fifth time to exit.

Program Button Operation

•The Program button allows you to set up the various preprogrammed modes (Wake, Leave, Return

and Sleep).

•Go to the next step by pressing Program again.

•Exit Program setup by:

- Timing out (4 minutes)

- Pressing Mode button

Note: Colored text below indicate element that should be blinking during setting procedure.

First press of Program:

Selects from available pre-program modes

Up/Down arrows cycle through Wake, Leave, Return and Sleep.

NOTE:

•Energy is not a part of this option.

•Once a preprogrammed mode is selected, that item remains displayed throughout to

indicate the mode you are programming.

•The current mode settings are displayed on the thermostat at each setup step.

Second press of Program:

Day setting

•Up/Down buttons cycle among all week, weekdays, weekend days and each day, as shown.

Page 9 of 32 Rev: 10/13/2015 9:13 AM

Third press of Program:

Start Time

•Up/Down arrows cycle through time in 15-minute increments. Note: when pressing the Down arrow, if

you come within 15 minutes of another preprogrammed mode time, you will not be able to increase

the time any further.

•Pressing and holding Up/Down arrows cycles faster.

Note: AM/PM changes automatically as needed.

Note: The start of one program mode is also the end of the previous program mode.

Fourth press of Program:

Cool setpoint

•Up/Down arrows cycle through temperature.

Fifth press of Program:

Heat setpoint

•Up/Down arrows cycle through temperature.

Sixth press of Program:

•Restarts the process to program another Mode/Day

NOTE: The four modes come preprogrammed. The defaults are for all days:

Day Modes

Start Time

Thermostat Mode

Heat Setting

Cool Setting

Wake

6:00AM

Auto

65°F (18°C)

75°F (24°C)

Leave

8:30AM

Auto

60°F (16°C)

80°F (27°C)

Return

5:00PM

Auto

65°F (18°C)

75°F (24°C)

Sleep

11:00PM

Auto

60°F (16°C)

80°F (27°C)

Page 10 of 32 Rev: 10/13/2015 9:13 AM

Fan and Hold Button Operations

Fan button operations

•The Fan button cycles between Auto and Always On.

•On the display, it simply indicates the text “Fan Always” when selected. There is no indication for Fan

Auto.

Hold button operations

•The Hold button overrides a preprogrammed mode until Hold is turned off.

NOTE:

•While Hold is enabled, the next preprogrammed time that comes in Time of Day Mode will be ignored.

•While Hold is enabled, the preprogrammed time notations are not shown (i.e. Wake, Leave, Return

and Sleep).

•Hold can be remotely enabled/disabled from an Insteon controller.

Master Button Operation

First press and hold:

Makes the local Insteon Thermostat the master temperature controller

•To perform this, press and hold Master button for 3 seconds.

Insteon Thermostat beeps once.

•Release.

Note: This is only valid if at least one Insteon Thermostat Zone Thermostat is linked to Insteon

Thermostat.

Before pressing Master button:

•Notice that the left remote sensor is currently

the Master temperature controller.

After pressing and holding Master button:

•Notice that the left remote sensor is no

longer the Master temperature controller.

•The local Insteon Thermostat is now the

Master controlling temperature.

Note: If no Insteon scene is programmed to a Insteon Wireless Thermostat, pressing and holding for 3

seconds will cause the Master segment to display while the button is being held.

Always On Auto

Hold On Hold Off

Autres manuels pour TempLinc 2441TH

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels INSTEON Thermostat

INSTEON

INSTEON TempLinc 2441TH Manuel utilisateur

INSTEON

INSTEON 2732-242 Manuel utilisateur

INSTEON

INSTEON TempLinc 2441TH Manuel utilisateur

INSTEON

INSTEON 2441V Manuel utilisateur

INSTEON

INSTEON 2441ZTH Manuel utilisateur

INSTEON

INSTEON 2441ZTH Manuel utilisateur

INSTEON

INSTEON TempLinc 2441TH Manuel utilisateur

INSTEON

INSTEON 2732-532 Manuel utilisateur

INSTEON

INSTEON 2441ZTH Manuel utilisateur

INSTEON

INSTEON TempLinc 2441TH Manuel utilisateur

INSTEON

INSTEON TempLinc 2441T Manuel utilisateur

INSTEON

INSTEON 2732-232 Manuel utilisateur

INSTEON

INSTEON TempLinc 2441TH Manuel utilisateur

INSTEON

INSTEON 2441ZTH Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur