Instanta 1000-C Mode d’emploi

The Professional’s Choice

Compact Range Models:

1000-C & 1000-M

Auto-Fill Catering Water Boiler

Installation And User Instructions

CONTENTS

CONTENTS & INTRODUCTION 2

SAFETY & ENVIRONMENTAL INFORMATION & DELIVERY CHECK-LIST 3

TECHNICAL SPECIFICATION 4

INSTALLATION 4

OPERATION 4

DAILY USE 5

CLEANING 5

MAINTENANCE, SPARES & SERVICE INFORMATION 5

SERVICE WARNINGS & FAULT DIAGNOSTICS 6

TECHNICAL SUPPORT 7

GUARANTEE 7

Introduction

Dear Customer,

Congratulations on the purchase of your

Instanta machine.

Your new water boiler is designed to give you

years of trouble-free service provided that the

instructions contained in this manual are followed.

All new series Instanta products are energy

efﬁcient, simple to operate and easy to service.

Find out more about Instanta products at

www.instanta.com

Safety Information

Please read the following carefully

before switching on this appliance.

A competent person should install this appliance in

accordance with the installation instructions for this

appliance and all relevant local and national standards

including the following:

• Health & Safety at Work Act

• IEE Regulations

• Local & national Building Regulations

• BS Codes of practice

• Water Supply Regulations

All personnel should be provided with sufﬁcient

training in the safe use of this appliance. A warning

notice displayed next to the machine is often helpful

in notifying users that the appliance contains and

dispenses near boiling water.

• Inform users that certain surfaces will become

hot (especially the draw-off tap). Care should be

taken to avoid potential injury from burns and

scalding whilst operating this appliance.

• In line with Health and Safety requirements we

recommend a risk assessment be carried out

after the boiler has been installed.

• Always disconnect the unit from the power

supply and allow it to cool down before servicing.

• The components in the draw-off tap are subject

to wear & tear. Check periodically (at least every

12 months), as part of a general maintenance

routine. We recommend that a spare tap

spring & tap washer (or upper tap assembly),

are held in case of emergencies and to

prevent down-time should the tap require

any maintenance/servicing.

• The unit must be earthed.

• Keep these instructions in a safe place near the

unit for future reference

Environmental Information

(Information on disposal for users of waste

electrical & electronic equipment)

The “crossed out wheelie bin” symbol on this product

means that discarded electrical and electronic

products should not be mixed with general waste.

Disposing of the product correctly will help to save

valuable resources and prevent any potential negative

effects on human health and the environment

which could otherwise arise from inappropriate

waste handling. For proper treatment, recovery and

recycling of end-of-life products, please contact

your dealer or supplier for further information, or

local authority for details of your nearest designated

collection point.

Delivery Checklist

Before starting installation, check that you have the

following parts;

1. Catering Water Boiler

2. Drip-tray

3. Drip-tray ﬁtting kit

4. White water inlet hose (3/4”BSP connection)

5. User instructions

Technical Information

Model 1000-C 1000-M

Width mm 218 218

Depth mm 465 465

Height mm 440 400

Tap

Clearance

mm 150 150

Power

Rating

KW 3.0 2.25

Rapid

draw-off

Litres 5 3

Weight

(Empty)

KG 8.9 8.4

Weight

(Full)

KG 15.9 14

Water Inlet

Pressure:

Bar 2 to 7 2 to 7 bar

Installation

The boiler must be installed on a horizontal work

surface with sufﬁcient strength to support its weight.

Locate in an area where there is adequate space to

use the boiler safely (e.g. free from risk of congestion

and tripping hazards).

Connection to Mains Water Supply:

Connect the WRAS approved water ﬁlling hose

(3/4”BSP) to the inlet connection point on the back

of the boiler and the other end to the mains water

supply, via an accessible isolating tap with a ¾”BSP

thread.

IMPORTANT: If micro-bore pipe is used instead of

the inlet hose supplied, the size must be minimum

OD 3/8”(10mm).

The water supply must have a pressure not

exceeding 7bar (96psi), and no lower than 2bar

(28psi) NOTE: If your water pressure exceeds 7bar,

ﬁt a suitable pressure reduction valve.

We regret that Instanta cannot be held responsible

for any machine malfunctions if the water pressure

exceeds that stated. If in doubt, consult your water

supply company

Electrical Connection:

The boiler must be Earthed.

Your machine is supplied with a standard 13amp

bonded plug with a 13amp fuse.

Overﬂow:

The drip-tray has a limited capacity and is designed

to handle small spillages and drips. Wherever

possible, we strongly recommend that it is connected

to a permanent waste outlet using the ﬁtting kit

provided.

If preferred, and as an alternative, the overﬂow can

be connected from the back of the machine using an

optional rear-overﬂow kit (Pt. No: ROFK1) available

from Instanta Spares Department (01704 502905).

IMPORTANT: Whichever overﬂow connection is

chosen, the diameter of the pipe used must be no

less than 15mm.

Whilst every reasonable precaution is taken to

prevent an overﬂow, Instanta cannot be held

responsible for any damage caused as a result

of incorrect installation or blockage of the

overﬂow or failure to direct the overﬂow to

a safe outlet.

Operation

First Use (once water and electrical connections

have been made);

• Switch boiler on.

• AMBER LIGHT will illuminate to indicate that the

boiler is ﬁlling with water.

• Once primed with water, the RED LIGHT will

illuminate to show that it is heating.

• When the boiler reaches the correct temperature

the GREEN LIGHT will show that the boiler is

ready.

IMPORTANT NOTE: In normal daily use, the boiler

may be used as soon as the GREEN LIGHT shows,

but on ﬁrst install, wait 15 minutes before starting

to use.

Regular Daily Use

• Switch boiler on

• Wait for the GREEN LIGHT. The water will then

be at the correct temperature.

• Dispense water via the lever tap.

(CAUTION: Take care as boiler dispenses

near-boiling water).

Cleaning

Clean the external surfaces of the boiler regularly to

maintain good hygiene

Empty the front drip-tray regularly

Wipe external surfaces of the boiler with a damp

cloth. Do not use abrasive materials on the outer

surfaces.

Wipe the draw-off tap each day to keep clean and

also prevent lime-scale deposits from building up

around the tap-outlet.

Maintenance

& Service Information

Descaling:

The boiler should be periodically checked for scale

build-up… see below:

In hard water areas, the boiler should be descaled

on a regular basis to maintain efﬁcient operation,

minimise energy consumption, and also retain

the water quality. The frequency depends on the

hardness of the local mains water supply and whether

or not a ﬁlter cartridge/water softener has been

installed.

To De-scale:

• Safety Caution: Disconnect machine from

power supply

• Empty the machine through the draw-off tap

and allow to cool

• Lift off the outer-lid.

• Remove tank-lid (four ﬁxing screws).

• Lift out the evaporation plates (inside of tank

- Remember order of removal).

• Remove as much scale as possible by hand.

Any scale which is difﬁcult to remove can be

dissolved by using a de-scaling solution.

• Wipe clean the level sensing probes.

• Flush with copious amounts of cold water to

ensure all traces of de-scaler are removed before

using the boiler again.

• Replace evaporation plates, tank-lid and

outer lid.

Draw-off Tap:

The tap spring and washer components are

subject to ware & tear. It is advisable to keep a

spare tap-spring and washer in case of emergencies.

Accessories & Spares (Tel: 01704 502905)

Replacement Tap Washer: TP1001/L

Replacement Tap Spring: TP1007/N

Multi-Filter Cartridge: AQ35

Head for Multi-Filter: AQ35H

Rear-overﬂow Kit: ROFK-1

(connection to perm waste)

A full range of spares and accessories are available

from our spares department.

Service Warnings

& Fault Diagnosis

Your boiler is ﬁtted with an intelligent fault diagnosing

system and is able to detect various fault conditions.

Some of these are less serious and the machine will

continue to operate as normal, while others are more

serious and will disable the unit.

Before calling for service, switch the machine off at

the mains supply. Draw-off a small amount of water

and then switch back on after 10 minutes. If the fault

does not clear, call technical support for advice.

Light

Indication:

Possible

Causes:

Action;

Flashing

Green:

The bottom

probe is scaled

up.

De-scale inside

of tank and level

sensors

Flashing

Orange:

• Water turned

off

• Inlet hose

kinked or bent

• Low

in-coming

water pressure

• Check water

supply and

stop-cock

• Check in-

coming water

is at minimum

of 2bar

Flashing

Red:

• Safety Control

has activated

• An internal

component has

failed

• Top probe not

recognised.

Water has

reached over-ﬁll

probe

• See Safety

Controls below

• Contact

Instanta

Technical

Support.

• Clean and

de-scale

probes

Flashing

Red &

Green:

• Over-boil safety

switch tripped

on initial heat-

up.

• Faulty Element

• Boil-dry

safety control

activated

• Re-set

required:

Isolate power

to appliance.

Push-in

manual reset

button (remove

back panel to

access).

• Call service if

fault persists.

Safety Controls:

The majority of possible faults have been covered

above. However, in certain circumstances, one of

two different safety controls within the boiler may

have activated;

1). Over-boil safety cut-out – activates if boiler

produces excess steam. This can be due to;

• lime-scale within the tank,

• a temporary interruption in the water supply.

• a faulty temperature sensor or internal

component (triac).

To Reset Boiler:

All Earlier Models: Switch off at the mains power

supply and allow the boiler to cool for ten minutes

before switching back on.

Safety Caution: Isolate boiler from power supply

before proceeding:

Later Models (All 1000-M models and 1000-C

units from Serial No: CB02863 – Jan 2014): Isolate

from mains electrical power supply and allow the

boiler to cool down. Remove back panel and push

the small reset button in the centre of the over-boil

cut-out (located next to the water inlet valve).

2). Boil-dry safety cut-out. This operates if the boiler

has been boiled dry, for example, due to lime scale

build-up or water starvation.

Safety Caution: Isolate boiler from power supply

before proceeding:

To reset boiler, Isolate from mains electrical supply.

Remove the back panel and push the small reset

button in the centre of the element cut-out.

In any of these events the indicator lamp will ﬂash red

or green or red and green. If the problem reoccurs

contact the Instanta Service Department

- 01704 502911

Service/Technical Support

Tel: 01704 502911

To ensure your service enquiry is handled as

efﬁciently as possible, please have the following

information available;

• Brief description of problem

• Product Type (model)

• Serial Number (label on right-hand side of machine).

This is essential

Guarantee

Your boiler is guaranteed for twelve months from

date of installation.

Our guarantee includes on site labour and parts

for problems caused by fault of manufacture and

component failure with the following exclusions:

• Problems caused by hard water and lime scale.

We regret that we cannot be held responsible for

problems caused by hard water

• Dripping Taps. These components are subject

to wear and tear but in the event of a tap failing

within twelve months of installation, we will be

pleased to replace the tap assembly by post.

Fitting is very simple and requires no tools. An

engineer call out is not necessary.

• Accidental damage, misuse or use not in

accordance with these instructions and damage

caused by incorrect installation.

The manufacturer disclaims any liability for incidental,

or consequential damages.

INSTANTA LIMITED

Canning Road Southport Merseyside PR9 7SN

Tel: (01704) 501114 Fax: (01704) 501115

IB33 - ISS: 02 FM 36413 EMS 75807

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Instanta Chaudière

Instanta

Instanta SureFlow CTS13SL Manuel utilisateur

Instanta

Instanta SureFlow Touch WMS6PB Mode d’emploi

Instanta

Instanta CTSP15PB Mode d’emploi

Instanta

Instanta Titan Pro Bulk Manuel utilisateur

Instanta

Instanta 3001F Mode d’emploi

Instanta

Instanta 1501F Mode d’emploi

Instanta

Instanta WM3 Mode d’emploi

Instanta

Instanta WMS6TF Mode d’emploi

Instanta

Instanta Barista Pro WB-2 Mode d’emploi

Instanta

Instanta WA2N Mode d’emploi

Instanta

Instanta SureFlow Plus Series Mode d’emploi

Instanta

Instanta SureFlow Compact Series Mode d’emploi

Instanta

Instanta InstaTap UCB Series Manuel de service

Instanta

Instanta 1000-C Mode d’emploi

Instanta

Instanta 1501F Mode d’emploi

Instanta

Instanta DB2000 Mode d’emploi

Instanta

Instanta CPF2100 Mode d’emploi

Instanta

Instanta Barista Pro SW Series Manuel utilisateur

Instanta

Instanta DB500 Mode d’emploi

Instanta

Instanta CTS11F Mode d’emploi

Instanta

Instanta CH1000 Mode d’emploi

Instanta

Instanta SureFlow Series Mode d’emploi

Instanta

Instanta 1500 Manuel de l'opérateur

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur