InSinkErator Model SS-50 Manuel utilisateur

SERVICE MANUAL

Commercial Disposers

SS-50

SS-75

SS-100

SS-125

SS-150

SS-200

SS-300

SS-500

SS-750

SS-1000

Service Manual i

Commercial Disposers

GENERAL INFORMATION .................................................................................................................................... 3

SAFETY SIGNALS ....................................................................................................................................................... 3

COMMERCIAL DISPOSERS ....................................................................................................................................... 3

PRIOR TO SERVICE CALL ......................................................................................................................................... 3

AFTER COMPLETING SERVICE ................................................................................................................................ 3

COMMERCIAL DISPOSER

PARTS LIMITED WARRANTY ..................................................................................................................................... 4

SERIAL NUMBER DATE CODE .................................................................................................................................. 4

SPECIFICATIONS ..................................................................................................................................................... 5

COLD WATER FLOW & DRAIN LINE DIAMETER ...................................................................................................... 5

DIMENSIONS .............................................................................................................................................................. 5

ELECTRICAL REQUIREMENTS ................................................................................................................................. 7

RECOMMENDED INSTALLATION .............................................................................................................................. 8

REMOVING DISPOSER .............................................................................................................................................. 9

INSTALLING DISPOSER ............................................................................................................................................. 9

PREPARATION FOR REPAIR .............................................................................................................................. 9

COMMON REPAIR AREAS ....................................................................................................................................... 10

TERMINAL BOX & TRIM BAND .................................................................................................................................11

GRINDING CHAMBER .......................................................................................................................................... 12

REPLACING WATER INLET ...................................................................................................................................... 12

REPLACING SHREDDER GASKET ......................................................................................................................... 12

REPLACING STATIONARY SHREDDER .................................................................................................................. 13

REPLACING ROTATING SHREDDER ...................................................................................................................... 14

REPAIRING UPPER END BELL ASSEMBLY ........................................................................................................... 15

UPPER END BELL (UEB) .................................................................................................................................... 15

ELECTRICAL REPAIRS ....................................................................................................................................... 18

OVERLOAD PROTECTOR ........................................................................................................................................ 18

CAPACITOR .............................................................................................................................................................. 19

BOTTOM COVER AND FAN ...................................................................................................................................... 20

LOWER END FRAME (LEF) ...................................................................................................................................... 21

REPLACING START SWITCH

(1 PHASE MODELS) ................................................................................................................................................. 21

STATOR ..................................................................................................................................................................... 22

MOTOR LEADS CONNECTIONS .............................................................................................................................. 23

WIRING DIAGRAMS .............................................................................................................................................. 24

TROUBLESHOOTING ........................................................................................................................................... 27

EXPLODED VIEWS & PARTS LISTS .............................................................................................................. 32

TABLE OF CONTENTS

Service Manual

Commercial Disposers

NOTES

_________________________________________________________________________________________________________

Service Manual 1

Commercial Disposers

Safety Signals

This symbol indicates potential personal injury hazards.

Obey all safety messages accompanying this symbol to

avoid possible injury or death.

DANGER indicates an imminently hazardous

situation which, if not avoided, will result in

death or serious injury.

WARNING indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury.

CAUTION indicates a potentially hazardous

situation which, if not avoided, may result in

minor or moderate injury.

Commercial Disposers

InSinkErator® manufactures commercial food waste disposers

with motors ranging from 1/2 horsepower through 10 horsepower.

The basic assembly of all SS Series commercial disposers is iden-

tical. However, electrical connections vary depending upon the

disposer specications, power supply, and electrical controls.

Specication Decal

The specication decal (Figure 1) located on the motor trim cover

indicates

• complete model number (example - SS150-24)

• serial number (includes manufactured date)

• amperage

• voltage

• phase

• horsepower.

NOTE: The correct part sheet (as designated by the complete

model number) must be referenced to order replacement parts.

DANGER

Figure 1. Specication Decal

Prior to Service Call

• Obtain the model number, serial number, voltage and phase

from the customer to prepare for the service call.

• Date of installation.

• Obtain the service history of the disposer.

• Make sure the customer has tried resetting the overload pro-

tector and has checked for foreign objects jammed in the

grind chamber (see “Troubleshooting” on page 25).

• Before troubleshooting for mechanical problems, determine if

the problem is electrical:

• To determine if the problem is in the switch or the dispos-

er, bypass all electrical starting and/or electrical controls

and run the disposer direct.

• Make sure the disposer electrical specications match

the electric power supply.

• Make sure the motor lead connections are correct for the

corresponding power supply and starting controls.

• Determine if there are electrical problems with other

kitchen appliances. This may indicate a problem in the

building’s electrical circuitry.

After Completing Service

Test the disposer for proper operation and ensure that the ttings

are secure and do not leak.

GENERAL INFORMATION

Service Manual

Commercial Disposers

Commercial Disposer

Limited Warranty

InSinkErator® commercial disposers are warranted against defects

in material and workmanship for one year from the date of installa-

tion. The warranty includes parts and labor, provided the service is

performed by an InSinkErator Factory Authorized Service Center.

This warranty does not apply if failure is due to :

• Faulty or improper electrical installation

• Faulty or improper plumbing installation

• Product abuse or misuse

• Accidental damage

• Grinding elements jammed by foreign objects

• Clogged drain lines

• Unit improperly sized or improper water ow (as specied in

the Disposer Sizing Chart and Recommended Cold Water

Flow Chart in this manual..

Commercial Disposer

Parts Limited Warranty

Replacement parts installed on OUT OF WARRANTY dispos-

ers are covered (parts and labor) for 90 days from the date

the parts are installed, provided the service is performed by an

InSinkErator Factory Authorized Service Center. To receive credit,

the Service Agency must provide a copy of the service invoice

given to the customer as a receipt for the replacement part.

Serial Number Date Code

Example: 09110000000 09 = Year of Manufacture

11 = Month of Manufacture

2009 09



Service Manual 3

Commercial Disposers

Cold Water Flow & Drain Line Diameter

Disposer Water Flow

GPM (LPM)

Drain Line Diameter

Inches (MM)

SS-50 3 (11) 1-1/2" (38)

SS-75 3 (11) 1-1/2” (38)

SS-100 5 (19) 1-1/2”(38)

SS-125 5 (19) 1-1/2” (38)

SS-150 7 (26) 2" NPT (51)

SS-200 7 (26) 2” NPT (51)

SS-300 8 (30) 3" NPT (51)

SS-500 8 (30) 3” NPT (51)

SS-750 10 (38) 3” NPT (51)

SS-1000 10 (38) 3” NPT (51)

Dimensions

IMPORTANT: Use the following dimension charts for adaptor height in place of InSinkErator sink bowl height when mounting directly

to a sink. Dimensions - Models SS-50, SS-75, SS-100 & SS-125.

NOTE:

Adaptors are available upon request for all competitor

sink bowls or cones.

Please have sink/bowl cone type with the necessary

dimensions when ordering adaptors.

* It is recommended to add legs (Part No.11757C) with No. 5 Mounting Assembly.

Figure 2. Dimensions - Models SS-50, SS-75, SS-100 & SS-125

SPECIFICATIONS

Service Manual

Commercial Disposers

NOTE:

Adaptors are available upon request for all competitor

sink bowls or cones.

Please have sink/bowl cone type with the necessary

dimensions when ordering adaptors.

Also available as a short body model. Reduces overall

height of disposer by 1” (25.4 mm).

Legs shipped in carton with unit. Assembly required prior to unit installation.

* It is recommended to add legs (Part No.11757C) with No. 5 Mounting Assembly.

Figure 3. Dimensions - Models SS-150 & SS-200

NOTE:

Adaptors are available upon request for all competitor

sink bowls or cones.

Please have sink/bowl cone type with the necessary

dimensions when ordering adaptors.

Also available as a short body model. Reduces overall

height of disposer by 3” (76.2 mm).

Unit shipped with legs installed from factory. Adjustment

required at time of unit installation.

Figure 4. Dimensions - Models SS-300, SS-500, SS-750 & SS1000

Service Manual 5

Commercial Disposers

Electrical Requirements

The electrical wiring on disposers shipped from the factory are

not connected for a specic voltage. Refer to the Standard Motor

Connection Wiring Diagram attached to the inside of the disposer

terminal box cover for the correct voltage connections.

Standard disposer voltages are:

• 115/208/230 volts for single phase electrical power

• 208/230/460 volts for three phase electrical power

NOTE: All amp ratings denote amp draw during a grind load.

NOTE: The disposer motor phase and voltage must be the same

as the line or power supply.

ELECTRIC SHOCK! The disposer must be

permanently grounded.

DANGER

SS-50

1/2 H.P.

-26 115/208-230V, 60Hz, 1 Ph, 8.4/4.0/4.2 amps, UL

-27 208-230/460V, 60Hz, 3 Ph, 2.0/2.1/1.1 amps, UL

-28 115/208-230V, 60Hz, 1 Ph. 8.4/4.0/4.2 amps, CSA

-29 208-230/460V, 60Hz, 3 Ph, 2.0/2.1/1.1 amps, CSA

SS-75

3/4 HP

-27 115/208-230V, 60Hz, 1 Ph, 10.0/4.3/5.0 amps, UL

-28 208-230/460V, 60Hz, 3 Ph, 2.0/2.4/1.2 amps, UL

-29 115/208-230V, 60Hz, 1 Ph, 10.4/4.3/5.0 amps, CSA

-30 208-230/460V, 60Hz, 3 Ph, 2.0/2.4/1.2 amps, CSA

SS-100

1 H.P.

-28 115/208-230V, 60Hz, 1 Ph, 11.6/5.1/5.7 amps, UL

-29 208-230/460V, 60Hz, 3 Ph, 2.2/3.0/1.5 amps, UL

-30 115/208-230V, 60Hz, 3 Ph, 11.6/5.1/5.7 amps, CSA

-31 208-230/460V, 60Hz, 3 Ph, 2.2/3.0/1.5 amps, CSA

SS-125

1-1/4 H.P.

-25 115/208-230V, 60Hz, 1 Ph, 10.6/4.5/5.3 amps, UL

-26 208-230/460V, 60Hz, 3 Ph, 3.5/4.0/2.0 amps, UL

-27 15/208-230V, 60Hz, 1 Ph, 10.6/4.5/5.3 amps, CSA

-28 208-230/460V, 60Hz, 3 Ph, 3.5/4.0/2.0 amps, CSA

SS-150

1-1/2 H.P.

-34 115/208-230V, 60Hz, 1 Ph, 12.2/5.7/6.1, amps, UL

-36 208-230/460V, 60 Hz, 3 Ph, 3.2/4.6/2.3 amps, UL

-37 208-230/460V, 60 Hz, 3 Ph, 3.2/4.6/2.3 amps, CSA

-38 115/208-230V,, 60 Hz, 1 Ph, 12.2/5.7/6.1 amps, UL, short body

-39 208-230/460V, 60 Hz, 3 Ph, 3.2/4.6/2.3 amps, UL, short body

-35 115/208-230V, 60 Hz, 1 Ph, 12.2/5.7/6.1 amps, CSA

SS-200

2 H.P.

-27 115/208-230V, 60 Hz, 1 Ph, 17.4/7.7/8.7 amps, UL

-29 208-230/460V, 60 Hz, 3 Ph, 3.3/5.0/2.5 amps UL

-31 115/208-230V, 60 Hz, 1 Ph, 17.4/7.7/8.7 amps, UL, short body

-32 208-230/460V, 60 Hz, 3 Ph, 3.3/5.0/2.5 amps, UL, short body

-28 115/208-230, 60 Hz, 1 Ph, 17.4/7.7/8.7 amps, CSA

-30 208-240/460V 60Hz, 3 Ph, 3.3/5.0/2.5 amps, CSA

SS-300

3 H.P.

-25 208-230/460V, 60 Hz, 3 Ph, 6.0/7.4/3.7 amps, UL

-27 208-230/460V, 60 Hz, 3 Ph, 6.0/7.4/3.7 amps, UL, short body

-26 208-230/460V, 60 Hz, 3 Ph, 6.0/7.4/3.7 amps, CSA

SS-500

5 H.P.

-28 208-230/460V, 60 Hz, 3 Ph, 8.4/8.8/4.4 amps, UL

-30 208-230/460V, 60 Hz, 3 Ph, 8.4/8.8/4.4 amps, UL, short body

-29 208-230/460V, 60 Hz, 3 Ph, 8.4/8.8/4.4 amps, CSA

Service Manual

Commercial Disposers

SS-750

7-1/2 H.P.

-13 208-230/460V, 60 Hz, 3 Ph, 9.7/12.4/6.2 amps, UL

-15 208-230/460V, 60 Hz, 3 Ph, 9.7/12.4/6.2 amps, UL, short body

-14 208-230/460V, 60 Hz, 3 Ph, 9.7/12.4/6.2 amps, CSA

SS-1000

10 H.P.

-10 208-230/460V, 60 Hz, 3 Ph, 11.0/13.0/6.5 amps, UL

-12 208-230/460V, 60 Hz, 3 Ph, 11.0/13.0/6.5 amps, UL, short body

-11 208-230/460V, 60 Hz, 3 Ph, 11.0/13.0/6.5 amps, CSA

Recommended Installation

Figure 5. Recommended Installation

Service Manual 7

Commercial Disposers

PREPARATION FOR REPAIR

DANGER

ELECTRIC SHOCK! Turn off water and

electrical supply. Discharge capacitor with

1000 ohm jumper wire (1 Phase only). Do

not use a screwdriver to discharge or

capacitor may be damaged.

Removing Disposer

1. Turn off electrical supply and water supply to disposer.

2. Disconnect cold water connection from disposer body water

inlet (if connected).

3. Disconnect waste line from disposer.

4. Remove terminal box retaining screw and terminal box cover.

See “Terminal Box & Trim Band” on page 9. Mark motor lead

wires and electrical supply wires, then disconnect wires and

grounding wire from disposer.

NOTE: Make sure sink can bear weight of disposer before legs

are loosened. In some cases, support disposer before loosening

or removing legs.

5. If equipped with legs and legs interfere with removing dis-

poser from mounting ange, pull O-ring down disposer leg,

turn each leg clockwise to raise legs and gain oor clearance.

6. Remove disposer from mounting ange by turning disposer

or loosening bolts as necessary (depending on mounting

ange).

7. To remove legs, remove black cap plug from bottom of sup-

port leg (Figure 6). Insert slotted screwdriver into open end of

leg support tube and turn stud counterclockwise until free of

upper end bell. Pull leg from disposer.

Installing Disposer

ELECTRIC SHOCK! Turn off water and

electrical supply. Discharge capacitor

with jumper wire (1 Phase only).

1. If unit was equipped with legs, insert leg assemblies through

end cover guide holes. Insert screwdriver into open end of leg

support tube and turn stud clockwise to install. Install O-ring,

washer and cap to each leg (Figure 6).

NOTE: On models SS-150 thru SS-200, legs are optional and rec-

ommended where the disposer is mounted to a thin gauge sink

(16 gauge minimum), dish table, using a #5 mounting assembly

or non-InSinkErator mounting adaptors. On models SS-300 and

above, legs are factory installed and recessed on the unit.

2. Attach disposer to the mounting assembly by positioning in

mounting ange and turning disposer into ange or tightening

bolts (depending on specic mounting).

3. Adjust legs so unit is supported evenly. Push O-ring up ush

with bottom of unit.

DANGER

4. Connect electrical supply wires to the motor leads. Refer-

ence the wiring diagram attached to the inside of the terminal

box or the Wiring Diagrams section of the Disposer Control

Center Installation manual.

5. Reinstall terminal box.

ELECTRIC SHOCK! Make sure electrical

wires are not pinched or damaged when

installing terminal box cover.

6. Connect waste line to disposer.

7. Connect cold water supply to disposer body water inlet (if pre-

viously installed).

8. Turn on electrical and water supply.

9. Test the disposer to ensure the cutting elements revolve

and the water ows automatically. Make sure the disposer is

securely mounted and does not leak from any of the connec-

tions.

Figure 6. Disposer Leg

DANGER

Autres manuels pour Model SS-50

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels InSinkErator Élimination des déchets

InSinkErator

InSinkErator Evolution Septic Assist Manuel utilisateur

InSinkErator

InSinkErator LC50-13 Mode d’emploi

InSinkErator

InSinkErator Evolution PRO Series Manuel utilisateur

InSinkErator

InSinkErator PRO 750 Manuel utilisateur

InSinkErator

InSinkErator Badger 500 Plus Manuel utilisateur

InSinkErator

InSinkErator 13954 Instructions d'utilisation

InSinkErator

InSinkErator Evolution Compact Manuel utilisateur

InSinkErator

InSinkErator EVOLUTION 200-2 Manuel utilisateur

InSinkErator

InSinkErator Badger 5 Manuel utilisateur

InSinkErator

InSinkErator Evolution Series Manuel utilisateur

InSinkErator

InSinkErator Badger1 Manuel utilisateur

InSinkErator

InSinkErator Badger 1 Manuel utilisateur

InSinkErator

InSinkErator Evolution PRO 880LT Manuel utilisateur

InSinkErator

InSinkErator Evolution Series Manuel utilisateur

InSinkErator

InSinkErator Badger 444 Manuel d'installation

InSinkErator

InSinkErator Evolution Series Manuel utilisateur

InSinkErator

InSinkErator Evolution Excel Manuel utilisateur

InSinkErator

InSinkErator Badger 100 Manuel utilisateur

InSinkErator

InSinkErator SS100-28 Manuel utilisateur

InSinkErator

InSinkErator Badger 1 Manuel utilisateur

InSinkErator

InSinkErator Badger 1 Manuel d'installation

InSinkErator

InSinkErator Model LC-50 Manuel d'utilisation

InSinkErator

InSinkErator Evolution Excel Mode d’emploi

InSinkErator

InSinkErator Badger 5XP Manuel utilisateur

Manuels Élimination des déchets populaires d'autres marques

Insinger

Insinger I-6 Manuel utilisateur

Franke

Franke CE-50 Manuel d'utilisation

Leafield Environmental

Leafield Environmental Envirobank 140 Feuille d'instructions

Meiko

Meiko TopCut B Manuel utilisateur

KitchenAid

KitchenAid KCDB250G2 Manuel utilisateur

Gladiator

Gladiator Garage Compactor Manuel utilisateur

Maytag

Maytag DFC1500 Manuel d'installation

Weber mt

Weber mt CR 7 Mode d'emploi

THERMEx

THERMEx WASTEMINATOR II Manuel utilisateur

Weber mt

Weber mt CR 7-II Hd Mode d'emploi

ROBINHOOD

ROBINHOOD SE390 Manuel utilisateur

Whirlpool

Whirlpool GC2000PE2 Manuel utilisateur

Scheppach

Scheppach HP3000S Instructions de montage

Haigh

Haigh Quattro Vanguard Original Manuel utilisateur

Maxmatic

Maxmatic 5000 Fiche technique

Toro

Toro FP-2200 Manuel utilisateur

Elephants Foot

Elephants Foot eDiverter Manuel utilisateur

Zanussi

Zanussi DU 4400 Manuel utilisateur