Innovative MAX Manuel utilisateur

MAX ROLL BENCH ASSEMBLY INSTALLATION

Complete Instructional Guide

! Attention!

Before starting the assembly of your benching

system, check floor surface to ensure a level starting

point. If your floors are damaged, heavily sloped or

contain obstacles, you may have issues with proper

bench setup. These issues should have been noted

during the Floor Layout/Quoting phase and may

need custom designed components to correct these

issues.

Innovative Growers Equipment, Inc. is not liable for

the replacement of parts and components.

Before starting the assembly of your benching

system, ensure that Bench Assembly Layout and

Staal & Plast tray gluing instruction packets are

available prior to starting installation.

If not, please contact Innovative Growers Equipment,

Inc. contact information located at the end of this

instruction packet.

7/16” & 3/4” WRENCHS & SOCKETS

TAPE MEASURE

TOOLS NEEDED FOR INSTALLATION

POWER DRILL/IMPACT

W/BITS & NUT DRIVERS

CAULK GUN

POP RIVET GUN

*Pneumatic Rivet Gun Suggested

2+ People Needed

for installation.

Estimated Time:

1-2 hours depending on

bench length.

2’ LEVEL

HAMMER DRILL W/

5/32 MASONRY BIT

UTILITY KNIFE

MALLET

VACUUM/BLOWOUT BULB

PARTS NEEDED FOR INSTALLATION

Confirm all parts are present before starting assembly. If parts are

missing or damaged refer to contact information on last page.

* Parts are only applicable if Bench Assembly Layout calls for

multiple parts.

Group

Part

Description

Refer to Bench

Assembly Layout/

Parts List for Lengths,

Dimensions and

Quantities

◼A1: Leg Units

◼A2: Load

Bearing Plug

◼A3: Stringer

Pipe 1” x 1”

◼*A4: Additional

Stringer Pipe 1”

x 1”

◼A5: Stringer

Insert .813” x 5”

Long

◼A6: Square to

Square Clamp

A3&4

◼B1: Anti-Tip

System

◼B2: Plain

Header Unit

◼C1: Rolling

pipe

Swedged/

Crimped End

◼C2: Rolling

Pipe Plain End

◼C3: Bench

Cross Bar

◼D1: Bench

Corner

◼D2: Aluminum

Side Rail –Longer

with 3/2 hole combo

on ends

◼*D3: Additional

Aluminum Side

Rail

◼D4: Aluminum

End Rail –Shorter

with 3/3 hole combo

on ends

◼D5: Joiner

Plates

◼D6: End Frame

(For 5’ wide or wider

benches only)

D2-D3

◼E1: End Tray

W/ Well

◼E2: Middle

Tray

◼E3: Filler Tray

◼E4: End Tray

No Well

◼F1: Pop-Rivet

◼F2: Self-

Tapping Screw

◼F3: ¼-20 Hex

Nut

◼F4: ¼-20 x .75”

Hex Screw

◼F5: ½” Flat

Washer

◼F6: Tap Con

3/16 x 1-3/4”

◼F7: Safety

Chain

◼F8: Angle

Bracket

STEP #1

Lay out Leg Units and Stringer Pipe.

◼Before (A1) Leg Units are removed from bundle, install (A2) Load Bearing Plugs into

uncrimped ends.

◼(A2) Load Bearing Plugs to be inserted in non-crimped bottom two openings. Shown

Fig. 1a.

◼Note: Mallet may be used to help seat

(A2) Load Bearing Plugs onto (A1) Legs Units

1a.

Table des matières

Autres manuels Innovative Support et étagère

Innovative

Innovative UltraRack URPS Manuel utilisateur

Innovative

Innovative EVO 5900 Manuel utilisateur

Innovative

Innovative 8519 Manuel utilisateur

Innovative

Innovative 9136 Manuel utilisateur

Innovative

Innovative 9400 Manuel utilisateur

Innovative

Innovative Winston Lift Single Manuel utilisateur

Innovative

Innovative 9035 CRT Guide d'installation

Innovative

Innovative Ella Manuel utilisateur

Innovative

Innovative PTS-04-ISC250 Manuel utilisateur

Innovative

Innovative 7020 Manuel utilisateur

Innovative

Innovative 9232-DC Manuel utilisateur

Innovative

Innovative 9120 Manuel utilisateur

Innovative

Innovative 7000 Manuel utilisateur

Innovative

Innovative LCD Monitor Arm 9103 Manuel utilisateur

Innovative

Innovative 9047 Manuel utilisateur

Innovative

Innovative 7000 Manuel utilisateur

Innovative

Innovative HAT Collective WINSTON-E Triple Manuel utilisateur

Innovative

Innovative 8408 Manuel utilisateur

Innovative

Innovative Ella Manuel utilisateur

Innovative

Innovative 8520 Manuel utilisateur

Innovative

Innovative PTS-04-LANE Manuel utilisateur

Innovative

Innovative WINSTON-E Series Manuel utilisateur

Innovative

Innovative 9049 Manuel utilisateur

Innovative

Innovative 7011 Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur