InnotechRV TPMS-400 Manuel
TPMS-4000 Tyre Pressure Monitoring System
Quick Setup Instructions
Charging
1. Before installing the InnoTechRV.com TPMS system first ensure the monitor is fully charged by
plugging it into a vehicle 1 V adaptor for at least 6 hours
. Turn the monitor on by pressing the middle button.
Programming Sensors (Alignment Mode
1. Slide a battery into each sensor (UNDER the metal terminal with +ve side UP) and replace the
cap. Do not over tighten as this may damage the o-ring and/or cap.
2. Put the monitor into Tyre Alignment Mode by pressing and holding the left and right buttons
simultaneously until the monitor beeps.
3. Press the left or right button to select the tyre position you wish to install a sensor on.
4. Screw a sensor onto that wheel. The sensor will immediately align with the monitor, the LED will
light green and the monitor will show the current tyre pressure. If the red LED light stays on and “-
- -” still shows at the top of the monitor display then the sensor has not alligned. Remove the
sensor, remove and replace the battery and replace the sensor on the tyre.
5. Repeat steps and 3 for all tyre positions.
6. When finished installing sensors, press and hold the left and right buttons again until the monitor
beeps.
Programming Individual Tyre Pressures
1. Once all sensors have been installed and aligned and you have taken the monitor out of alignment
mode, press and hold the middle button until the monitor beeps. The first programmed tyre
position will flash and the default pressure level will show.
. Press the left or right buttons to decrease or increase the desired normal cold tyre pressure level
for that wheel position. Note; the pressure will increment by 0.1 psi each time the button is
pressed but holding the button will rapidly increment the pressure level.
3. Press the middle button to move to the next tyre and repeat step until the normal cold tyre
pressures for all wheels have been preset.
4. Once the pressures for all wheels have been set, the next press of the middle button will show
pressure units and by pressing the left or right buttons you can change between PSI and bar.
5. Pressing the middle button again will take you to temperature units and pressing the left or right
buttons you can change between F and C.
6. Pressing again will take you to the LoOFF function. Please refer to the New Features sheet.
7. Once you have set your temperature units, hold down the middle button for 5 secs until the monitor
beeps. You have now finished programming.
PTO....
Australia New Zealand USA
WiPath Communications Pty Ltd (ABN: 86 093 464 496) WiPath Communications Ltd WiPath Communications LLC
Postal: PO Box 7, Chester Hill, NSW 16 , Australia Postal: PO Box 8798, Symonds St, Auckland 1150, NZ 4845 Dumbbarton Court, Cumming, GA 30040
Street:13/10 Straits Ave, South Granville, NSW 14 , Australia Street: 3/ Haultain St, Eden Tce, Auckland, New Zealand P: +1-770-844 6 18 F:+1-770-844 6574
P: +61- -8004 0535 F:+61- -9681 4010 E:[email protected] P: +64-9-30 114 F:+64-9-30 1148 E:[email protected] E: [email protected]
Deleting or Moving Sensors
If you wish to change a sensor from one tyre to another, or replace a sensor on a particular tyre
that sensor must be deleted from its original position first and any sensor already programmed
into the new position must also be deleted from the monitor.
1. Put the monitor into Tyre Alignment Mode by pressing and holding the left and right
buttons simultaneously until the monitor beeps.
2. Press the left or right button to select the tyre position you wish to delete or change a
sensor on.
3. Remove the sensor from the tyre.
4. Hold down the centre button for that tyre position until the monitor beeps and three dashes
appear instead of a pressure reading for that position.
5. Repeat steps -4 for any other tyre positions that you wish to delete/change.
6. Re-install sensors using instructions for Programming Sensors above.
Deleting All Sensors
If you wish to delete all sensors to re-align all sensors:
1. Put the monitor into Tyre Alignment Mode by pressing and holding the left and right
buttons simultaneously until the monitor beeps.
2. Press and hold both the left and centre buttons until the monitor beeps. This will delete all
sensors from the monitor.
3. Re-install sensors using instructions for Programming Sensors above.
Turning The Monitor Off
To Turn the Monitor Off, ensure the Monitor is no longer in programming or alignment mode then
press and hold the middle button for about 8 seconds until the display disappears. It will beep as
it goes back into programming mode but do not release the button until it turns off.
Table des matières
Autres manuels InnotechRV Instrument de mesure
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur