Inmes IF-8500 Manuel utilisateur

Dear Customer,

Thanks for allowing us to share the experience of using an Inmes product.

This manual has been formulated by our technical team specially for you, with the objective of instructing

you on how to use this equipment with safety and productivity.

The IF-8500 CNC Drilling Machine has been developed within the highest technology, to solve your

drilling problems in wood boards, allowing you to get the best value for money additionally to a great finishing

adding more value to the furniture.

Visit our brand website to learn about our new releases and our full product line.

http://www.inmes.com.br

If necessary, contact your distributor to get technical assistance.

Write down the serial number of your equipment below.

Note: INMES Industrial LTDA. Reserves the right to change this manual without previous notice.

INMES Industrial LTDA. –IF-8500 Drilling Machine 

INDEX 
 
–SAFETY INSTRUCTIONS ................................................................................................................. 3 
1 –Safety Warnings............................................................................................................................. 3 
2 –Before using the machine............................................................................................................... 3 
3 –Tools Specifications....................................................................................................................... 4 
4 –Before every use............................................................................................................................. 5 
5 –Important information for the reduction of risks of accidents ....................................................... 5 
6 –Protection ....................................................................................................................................... 6 
6.1 –Safety Labels............................................................................................................................... 6 
7 –When finished operating the machine............................................................................................ 9 
–RECEIVING AND GETTING ACQUAINTED WITH THE IF-8500 CNC DRILLING MACHINE9 
1 –Receiving the IF-8500 Drilling Machine ....................................................................................... 9 
2 –Working Area............................................................................................................................... 13 
3 –Getting Acquainted with the IF-8500 Drilling Machine.............................................................. 14 
4 –Learning about the Control Panel................................................................................................. 15 
5 –Learning about the Touch Screen Interface ................................................................................. 16 
–TECHNICAL SPECIFICATIONS..................................................................................................... 19 
–INSTALLATION............................................................................................................................... 20 
1 –Loading and Unloading the Equipment ....................................................................................... 20 
2 –Characteristics of the Installation Area........................................................................................ 20 
3 –Electrical Installation.................................................................................................................... 21 
4 –Installation of the Compressed Air System.................................................................................. 22 
5 –Installation of the Exhaust System............................................................................................... 23 
5.1 –Electrical Installation of the Exhaust......................................................................................... 23 
6 –Software Installation .................................................................................................................... 25 
–SECURITY SYSTEM........................................................................................................................ 26 
1 –Movable Protection of the Drilling Set Access............................................................................ 26 
2 –Emergency Button........................................................................................................................ 26 
3 –Reset Button................................................................................................................................. 29 
–OPERATION...................................................................................................................................... 30 
1 –Turning the Machine on and off................................................................................................... 30 
2 –Entering the Work Schedule in the Drilling Machine.................................................................. 33 
4 –Jog Function................................................................................................................................. 42 
5 –Cycles Function............................................................................................................................ 45 
–MAINTENANCE............................................................................................................................... 46 
1 –Cleaning ....................................................................................................................................... 46 
1.1 –Air Filters Cleaning................................................................................................................... 46 
1.2 –Axis Y Link Chain Cleaning..................................................................................................... 47 
1.3 –Axis Z Sensor Cleaning............................................................................................................. 48 
1.4 –Cleaning the Head Cylinder and Head Lock Plate.................................................................... 48 
1.5 –Cleaning the Axis X Linear Guide and Gear Rack................................................................... 49 
2 –Lubrication ................................................................................................................................... 50 
2.1 –Oil Tank..................................................................................................................................... 50 
2.2 –Chain Lubrication...................................................................................................................... 51 
3 –Compressed Air Regulator........................................................................................................... 53 
4 –Tool Replacement ........................................................................................................................ 53 
5 –Belt Slack Adjustment.................................................................................................................. 62 
5.1 –Saw Belt .................................................................................................................................... 62 
–POSSIBLE PROBLEMS –CAUSES –SOLUTIONS...................................................................... 64 
–EXPLODED VIEWS.......................................................................................................................... 68 
 

INMES Industrial LTDA. –IF-8500 Drilling Machine

1 –SAFETY INSTRUCTIONS

In order to increase the safety of the operator and the durability of your equipment, some caution is re-

quired during its installation and operation.

1.1 –Safety Warnings

Safety information, which, if not complied with, will cause serious risks to the operator’s

life.

Safety information, which, if not complied with, may cause serious risks to the operator’s

life;

Safety information, which, if not complied with, may cause injuries to the operator.

1.2 –Before using the Machine

✓Carefully ready the entire instruction manual before operating the equipment;

✓Keep this manual in a location that is easy for the operator to access;

✓If you are not totally familiarized with how to operate the machine, seek for guidance from a professional;

✓Place the machine so that the working space is suitable to the operator;

✓Do not expose or use the machine in inappropriate sites.

✓Always wear protection glasses;

✓Keep hands away from the moving parts of the machine;

✓Never place your hands or any objects that are not the actual material to be drilled through the openings

where it should be inserted. Not complying with this requirement may cause severe injuries to the operator

and damage to the equipment.

✓Always wait for the moving parts of the machine to stop before any maintenance or adjustment and make

sure that the machine is not connected to the electricity.

✓While you are working, pay full attention to the functioning of the machine. Any lapse of attention may

cause severe injuries.

✓Never connect the Earth cable (green and yellow) to the neutral. Always connect it to a functioning ground

wiring;

✓Never use drills and cutters out of the recommended specifications. Not complying with this requirement

may cause severe damage to the equipment.

✓It is advisable to work only wood or wood boards such as MDF, MDP or similar. It is not allowed under

any circumstances to work with any other type of material;

✓Make your work safer, making sure that all safety items described in this Instruction Manual are followed

and are functioning normally.

✓Before leaving the work site, be sure that the machine is completed turned off.

✓The machine can only be safely used if the operator thoroughly follows the operation and safety

instructions.

✓It is fundamental to read this manual before using this machine so that you know how the machine Works

and its limitations.

✓Make sure that all safety devices are installed in the machine and that the machine is connected to a dust

extraction system.

✓Leave enough space around the machine and a good lighting in the workshop.

✓When changing the tools or when performing a maintenance job, the machine must always be disconnected

INMES Industrial LTDA. –IF-8500 Drilling Machine

from its power supply.

✓Drills, cutters and blades that are not correctly sharpened or are in bad conditions not only decrease the

work quality but also increase the risks of accidents.

✓Always wear appropriate clothes. Loose or torn clothes are very dangerous.

✓Keep children away from the machine and from the workshop.

✓To avoid damages to your hearing, it is recommended that you wear hearing protection while you are close

to the machine.

✓Make sure that all maintenance work is done periodically. Maintenance Works can only be performed with

the machine disconnected from its power supply, disabling any accidentally activation of the machine.

✓Thoroughly read the cleaning instructions for the machine and only clean in when it is disconnected from

electricity.

✓Perform weekly tests of the following electrical components: emergency buttons and test whether the

machine can be operated with the doors open.

✓Always wear hearing protection when operating the machine.

1.3 –Tools Specifications

The saw blade must comply with the following specifications:

90mm –3 9/16”

20mm –13/16”

Rotation limit equal or superior to 3500rpm;

Teeth: 24

To be adequate to the type of material to be cut (wood boards and

similar).

The drill must comply with the following specifications:

10mm –3/8”

35mm –1 3/8”

58mm –2 ¼”

4mm –3/16”

Rotation limit equal or superior to 5500rpm;

To be adequate to the type of material to be cut (wood boards and

similar).

The drill must comply with the following specifications:

10mm –3/8”

15mm –9/16”

58mm –2 ¼”

4mm –3/16”

Rotation limit equal or superior to 5500rpm;

To be adequate to the type of material to be cut (wood boards and

similar).

INMES Industrial LTDA. –IF-8500 Drilling Machine

The drill must comply with the following specifications:

10mm –3/8”

8mm –5/16”

58mm –2 ¼”

4mm –3/16”

Rotation limit equal or superior to 5500rpm;

To be adequate to the type of material to be cut (wood boards and

similar).

The drill must comply with the following specifications:

10mm –3/8”

5mm –3/16”

58mm –2 ¼”

4mm –3/16”

Rotation limit equal or superior to 5500rpm;

To be adequate to the type of material to be cut (wood boards and

similar).

In the tool head, one of the compartments has a red lid (01) and serves

only for left sided tools, as indicated on the image beside.

1.4 –Before every use

Check for loose or damaged parts.

Remove eventual cutting residues from the machine;

Never use the machine if any original part or protection are missing.

1.5 –Important information for the reduction of risks of accidents

✓Broken or damaged drills, cutters and blades must not be used;

✓Before starting to work with the machine, make sure that no objects have been left over it;

✓Adapted or damaged parts must not be used;

✓When any anomaly on the machine is detected, turn it off and disconnect it from electricity and perform the

required maintenance;

✓The machine must not be used if any protection is not working;

✓Only use sharpened drills, cutters and blades and in perfect working conditions;

✓Keep the cutting tools clean;

✓Always keep the working area clean, the dust resulting from work can make the floor slippery;

INMES Industrial LTDA. –IF-8500 Drilling Machine

✓The machine must not be used near inflammable liquids, dust, vapor or gases;

✓People under 18 years old are not allowed to operate the machine;

✓Untrained people must be kept away from the machine;

✓The operator must be trained by qualified personnel to operate this equipment;

✓When installed the drill, cutter or blade, check the its mounting and the rotation direction, being careful not

to mount it backwards Fig. 1.2.

Fig. 1.2

✓The existing protections must not be removed. Not complying with these recommendations may

cause serious accidents;

1.6 –Protection

During the operation of the equipment:

✓Do not wear loose clothes, jewelry or ties;

✓Keep your hair away, wear a protection cap if necessary;

✓Always wear hearing protection;

✓Always wear protection glasses;

Always remember: A minor distraction is enough to cause serious accidents;

1.6.1 –Safety Labels

INMES Industrial LTDA. –IF-8500 Drilling Machine

Label

Indication

Indicates the safety rules that must be followed when

operating the machine.

Risk of crushing, keep hands away.

Indicates the use of appropriate clothes.

Indicates the use of hearing protection.

INMES Industrial LTDA. –IF-8500 Drilling Machine

Indicates the use of eye protection.

Indicates the use of protection shoes.

Indicates the use of gloves.

Risk of electric shock

INMES Industrial LTDA. –IF-8500 Drilling Machine

1.7 –When finished operating the machine

✓Turn the machine off;

✓Turn off the Main Switch of the machine;

✓Turn the circuit breaker off;

✓Clean up the machine and leave it ready for the next operation;

Warning

To request replacement parts, use the parts diagram and the parts list that can be found at the end of this

manual, always referring to the parts codes when ordering.

This manual is extremely useful when replacement parts are needed, therefore, keep it at an appropriate

site. In case you own more than one equipment of the same model, identify it writing the serial number down

on its respective manual on page 2 2.

2 –RECEIVING AND GETTING ACQUAINTED WITH THE IF-8500 CNC DRILLING

MACHINE

2.1 –Receiving the IF-8500 Drilling Machine

When receiving the machine, please check to make sure all items that go with it are present.

Item

Description

Quantity

IF-8500 Drilling Machine

Infeed/Outfeed Table

Infeed/Outfeed Table finishing

Structure Leaning Support

Table Assembling Kit Carton Box IF-8500

Assembling Kit Carton Box IF-8500

Right Rear Board

Left Rear Board

Bottom Dust Collector

INMES Industrial LTDA. –IF-8500 Drilling Machine

Table des matières

Manuels Percer populaires d'autres marques

Makita

Makita BDF456 Manuel utilisateur

Black & Decker

Black & Decker LDX220 Manuel utilisateur

Hitachi

Hitachi DH 40MA Manuel utilisateur

Challenge

Challenge JO Manuel de référence technique

Makita

Makita LXFD01 Manuel utilisateur

Festool

Festool T18+3 Manuel utilisateur

Milwaukee

Milwaukee M12 FPDX-202X Manuel utilisateur

EINHELL

EINHELL TE-RH 32 E Manuel utilisateur

Makita

Makita DHP484 Manuel utilisateur

Makita

Makita FD05 Manuel utilisateur

Bosch

Bosch PSB 530 RA Manuel utilisateur

Maximum

Maximum 054-1359-4 Manuel utilisateur

Makita

Makita HP332D Manuel utilisateur

Raider

Raider RDP-HD31H Manuel utilisateur

Bort

Bort BPM-1400x2 Manuel utilisateur

Black & Decker

Black & Decker 7266 Manuel utilisateur

KENT USA

KENT USA TRD1230 Manuel utilisateur

Bosch

Bosch GSB 19-2 RE Manuel utilisateur