Ingersoll-Rand ZGB015-KIT Manuel utilisateur
Form 47740328
Edition A
June 2021
©2021 Ingersoll Rand
Purpose/Objective: This document provides assembly instructions for the Zero Gravity portion of the 150 lbs., 200 lbs., 350 lbs., and 500 lbs. Balancers.
The use of other than genuine In ersoll Rand replacement parts may result in safety ha ards, decreased performance and increased maintenance and
will invalidate all warranties.
For further assistance or parts needed, contact local distributor or IR representative.
Original instructions are in English. Other languages are a translation of the original instructions.
Prior to installing the product, carefully inspect it for possible shipping damage.
Conversion Kit: Zero Gravity Balancer Assembly
WWAARRNNIINNGG
• Prior to installation refer to Product Safety Information Manual for all sections of installation.
• Always wear eye protection when operating or performing maintenance on this Product.
• Make sure that electrical power to the system has been disconnected.
• Always shut off main air supply and bleed down before disconnecting air supply hose before
installing, removing or adjusting any accessory on this Products, or before performing any
maintenance on this Product.
• Never perform maintenance on the Product while it is supporting a load.
• Before performing maintenance, tag controls: WARNING - DO NOT OPERATE - EQUIPMENT
BEING REPAIRED.
• Only allow personnel trained in service and repair of this Product to perform maintenance.
• After performing any maintenance on the Product, test Product before returning Product to
service.
• The lower sheave block or hook assembly must be lying on the floor or a maintenance platform
before beginning service.
CCAAUUTTIIOONN
Owners and users are advised to examine specific, local or other regulations, including American
Society of Mechanical Engineers (ASME) and/or OSHA Regulations which may apply to a particular
type of use of this product before installing or putting product to use.
Table 1. Product Information Manuals
Publication CCN
Product Safety Manual 16598831
Product Information Manual 54072541
Product Parts Information Manual 16598849
Product Installation Manual 47646669001
Product Maintenance Manual 16598856
ZGB User Manual 47726957001
2Form 47740328 Edition A
ZGB Retrofit Kit Components
Fi ure 1. ZGB Retrofit Kit Components Drawin
1
2
3
4
5
Table 2. ZGB Retrofit Kit List
Item No. Description of Part Total Qty.
Part Number
ZGB015-KIT for
BW015080
Balancers
ZGB020-KIT for
BW020120
Balancers
ZGB035-KIT for
BW035080
Balancers
ZGB050-KIT for
BW050080
Balancers
1Suspension Kit 1 ZGS00
2 Manifold Kit 1 ZGB-MANIFOLD
3 Brackets Kit 1 ZGE06 ZGE10
4 Control Box Kit 1 ZGB015 ZGB020 ZGB035 ZGB050
5 Command Handle 1 ZGP00B
6(a) Spiral Wire 1 ZGC2
(a) Item not illustrated.
3 Form 47740328 Edition A
Installation
1. Mount Balancer on V-block or other stable surface to support
cylindrical housing. Install two bushings into the suspension ears of
the housing.
2. Mount the suspension brackets onto the housing using a set of
bolts and nuts. Make sure that the flanges of both brackets are facing
outwards.
3. Using a 7/8” and 13/16” wrench to secure the nuts and bolts.
Torque to 54 ft-lbs.
4. Apply thread sealant (example: Loctite 567 or similar) to the fitting
for the manifold.
5. Tighten the fitting and position it to the orientation shown below.
4Form 47740328 Edition A
6. Install O-ring on back side of manifold. A little bit of grease or lube
(example: Super Lube Silicone O-ring Grease or similar) can be used
to help hold the O-ring in place if needed. Install the manifold to the
unit using 1/4" allen wrench, the provided screws and washers.
Torque screws to 8 ft-lbs.
7. Assemble the control box onto the suspension brackets using a
5mm allen wrench, the 4 screws and set of washers. Torque screws to
8 ft-lbs.
8. Air hose should be supplied at pre-cut length. If not, cut the hoses to the following lengths.
a. 150 lbs capacity:
i. Hose #1: 30 cm (11- ¾”)
ii. Hose #2: 17.5 cm (7”)
b. 200/350/500 lbs capacity:
i. Hose #1: 36 cm (14- ¼”)
ii. Hose #2: 19 cm (7- ½”)
9. Gather all the hose/fittings/clamps.
10. Insert fitting #1 into hose #1 (labeled in step 9). Coat the fitting with lubricant/sealant (example: Loctite 567 or similar) for ease of
installation.
11. Remove nut on hose fitting and insert the hose into the hole in the suspension kit. Insert the hose clamp and pinch the ears to secure the
hose to the fitting. Do not tighten the nut on hose fitting.
12. Insert the hose clamp onto the open end of hose #1. Coat fitting #2 with lubricant/sealant (example: Loctite 567 or similar). Install fitting
#2 on hose #1. Pinch the ears of the hose clamp to secure the hose to the fitting.
5 Form 47740328 Edition A
13. Check the presence of the O-ring in the fitting. If necessary, lightly coat the seal with grease/lube (example: Super Lube Silicone O-ring
Grease or similar).
14. Install the fitting on the bottom hole of the control box.
15. Tighten the nut from step 11.
16. Coat the manifold fitting with lubricant/sealant (example: Loctite 567 or similar). Install hose #2 onto the fitting of the manifold. Insert
the hose clamp and pinch the ears to secure the hose to the fitting.
17. Insert the hose clamp onto the end of hose #2. Coat fitting #2 with lubricant/sealant (example: Loctite 567 or similar). Install hose #2 on
fitting #3. Pinch the ears of the hose clamp to secure the hose to the fitting. (It may be easier to install hose on the fitting if the fitting is off of
the manifold).
18. Check the presence of the O-ring in the fitting. If necessary, lightly coat the seal with grease/lube (example: Super Lube Silicone O-ring
Grease or similar).
19. Thread the fitting into the top of the control box. Tighten the nut using a wrench, orienting the fitting in a horizontal direction.
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Ingersoll-Rand Contrôleurs
Ingersoll-Rand
Ingersoll-Rand EC24N Manuel utilisateur
Ingersoll-Rand
Ingersoll-Rand X4I Fiche technique
Ingersoll-Rand
Ingersoll-Rand 150BMPC Series Guide de configuration
Ingersoll-Rand
Ingersoll-Rand EC24E Manuel utilisateur
Ingersoll-Rand
Ingersoll-Rand Intellisys S3 Manuel utilisateur
Ingersoll-Rand
Ingersoll-Rand ST400 Series Guide de configuration
Ingersoll-Rand
Ingersoll-Rand X4I Manuel utilisateur
Ingersoll-Rand
Ingersoll-Rand ESCB20 Manuel utilisateur
Ingersoll-Rand
Ingersoll-Rand Delvo ESCB50 Manuel utilisateur
Ingersoll-Rand
Ingersoll-Rand ARO 67442 Manuel utilisateur
Ingersoll-Rand
Ingersoll-Rand EC24N Manuel utilisateur
Ingersoll-Rand
Ingersoll-Rand SE Guide d'installation
Ingersoll-Rand
Ingersoll-Rand SS100 Series Guide de configuration
Ingersoll-Rand
Ingersoll-Rand TS900 Series Guide de configuration
Ingersoll-Rand
Ingersoll-Rand ST1000 Series Guide de configuration
Ingersoll-Rand
Ingersoll-Rand TS1401 Series Guide de configuration
Ingersoll-Rand
Ingersoll-Rand ECM24N Manuel utilisateur
Ingersoll-Rand
Ingersoll-Rand ST700 Series Guide de configuration
Ingersoll-Rand
Ingersoll-Rand SS175 Series Guide de configuration
Ingersoll-Rand
Ingersoll-Rand 150T P Series Guide de configuration
