InFocus IN42 Manuel utilisateur

IN42/C445 NETWORKING GUIDE

This guide is only intended to explain Network Functions. For safety, operations or any other issues, refer to the pro-

jector’s User’s Guide or Safety Booklet.

TABLE OF CONTENTS

Network Functions 2

Before using the network functions 2

Configuring and controlling the projector via a web browswer 3

Settings 5

Network Information 6

Network Setting 7

Mail Settings 8

Alert Settings 9

Schedule Settings 10

Date/Time Settings 11

Security Settings 12

Projector Control 13

Projector Status 14

Network Restart 15

Failure and Warning Alerts via E-mail 15

Mail Settings 15

Projector management via SNMP 17

Controlling the projector via scheduling 18

Date/Time Settings 18

Schedule settings 18

Network Functions

This projector is equipped with the following network functions.

Configuring and Controlling the Projector via a Web Browser

You can change the settings of or control the projector via a network by using a web browser from a PC that is con-

nected to the same network.

Failure & Warning Alerts via E-mail

The projector can automatically send an alert to specified e-mail addresses when the projector requires maintenance or

has encountered an error.

Projector Management via SNMP

This projector is SNMP (Simple Network Management Protocol) compliant, allowing you to monitor it from a remote

location using SNMP software.

Controlling the Projector via Scheduling

You can schedule the projector to perform various functions according to the DATE and TIME.

Before using the network functions

To use the network functions of this projector, the projector must be configured to suit your network. Consult with

your network administrator before connecting the projector to your network. Incorrect network configuration of this

projector may cause problems on your network. Connect to the Gateway (The router/PC that forwards traffic to a des-

tination outside of the subnet of the transmitting device) from the network terminal on the projector using a CAT-5

cable and configure the following settings.

If using a network with DHCP enabled:

The projector’s network settings can be configured automatically when [DHCP] on the network menu is set to On

(the checkbox is checked). Please refer to DHCP in the User’s Guide Network menu. If a fixed / static IP address is

required, please configure your projector according to the steps in the following section.

If using a network system that does not have DHCP enabled or if using a fixed IP address on a network

system equipped with DHCP enabled:

Configure the following settings on the network menu.

1[DHCP]: Disable DHCP (Set [DHCP] to Off (the checkbox is unchecked).

2[IP ADDRESS]: Enter an appropriate IP address for the projector to connect to your network.

3[SUBNET MASK]: Enter an appropriate SUBNETMASK for the projector to connect to your network.

4[DEFAULT GATEWAY]: Enter an appropriate Gateway (the router/PC that forwards traffic to a destination out-

side of the subnet of the transmitting device) address for the projector to connect to your network.

Configuring and controlling the projector via a web browser

You can adjust or control the projector via a network from a web browser on a PC that is connected to the same net-

work.

NOTE:

• Internet Explorer 5.5 or higher or Netscape 6.2 or higher are required.

• If JavaScript is disabled in your web browser configuration, you must enable JavaScript in order to use the projec-

tor web pages properly. See the Help files for your web browser for details on how to enable JavaScript.

• If no operations are performed via a web browser for approx. 50 seconds the system will automatically log off.

Please Re-log on to continue operations via a web browser.

• After you logon, a small, blank window will appear behind the main operation window. Please do not close this

small, blank window. If this window is closed, the system will automatically log off after certain period of time

even if an operation is being performed. The small, blank window will close when the main operation window is

closed.

• The small, blank window may be considered a pop-up and be blocked if your browser or other security software

is set to block pop-ups. If the window is blocked, you need to choose the option to allow pop-ups to be shown.

• It is recommended that all web browser updates be installed. It is especially recommended that all users running

Internet Explorer on a Microsoft Windows version prior to Windows XP Service Pack 2 install security update

Q832894 (MS04-004) or the web browser interface may not be displayed correctly. And when using an older ver-

sion of Internet Explorer, during operations the browser will log out after 50 seconds.

When configuring or controlling the projector via a web browser, an ID and password are required. There are two

types of IDs, Administrator IDs and User IDs. The following chart describes the differences between user and admin-

istrator IDs.

Item Description Administrator ID User ID

Network Info Displays the projector’s current net-

work configuration settings.

YES YES

Network Settings Displays and configures network set-

tings.

YES N/A

Mail Settings Displays and configures e-mail

addressing settings.

YES N/A

Alert Settings Displays and configures failure &

warning alerts.

YES N/A

Schedule Settings Displays and configures schedule set-

tings.

YES N/A

Date/Time Settings Displays and configures the date and

time settings.

YES N/A

Security Settings Displays and configures passwords

and other security settings.

YES N/A

Projector Control Controls the projector. YES YES

Projector Status Displays and configures the current

projector status.

YES YES

Network Restart Restarts the projector’s network con-

nection.

YES N/A

Below are the factory default settings for administrator IDs, user IDs and passwords.

Item ID Password

Administrator

Administrator <blank>

User ID User <blank>

Settings

Refer to the following for configuring or controlling the projector via a web browser.

Example: If the IP address of the projector is set to 192.168.1.10:

1Enter [http://192.168.1.10] into the address bar of the web browser and the screen below will be displayed.

2Enter your ID and password and click [Logon].

If the logon is successful this screen will be displayed (if logged on as an Admin).

3Click the desired operation or configuration item on the main menu located on the left-hand side of the screen.

Network Information

NOTE: All screen images shown in this document are screens of a logon using an Administrator’s ID. Any Adminis-

trator-only functions will not be displayed when using a User ID.

Displays the projector’s current network configuration.

Item Description

DHCP Displays the DHCP configuration settings.

IP Address Displays the current IP address.

Subnet Mask Displays the Subnet Mask.

Default Gateway Displays the Default Gateway.

MAC Address Displays the MAC Address.

Firmware Date Displays the network firmware time stamp (Admin ID only).

Firmwave Version Displays the network firmware version number (Admin ID only).

Network Setting

Displays and configures network settings.

NOTE:

• The new configuration settings are activated after restarting the network connection. When the configuration set-

tings are changed, you must restart the network connection. You can restart the network connection by clicking

[Network Restart] on the main menu.

• If you connect the projector to an existing network, consult a network administrator before setting server

addresses.

Item Description

IP Configuration

DHCP On/ Off

IP Address

Subnet Mask

Default Gateway

Configures network settings.

Enables/disables DHCP.

Configures the IP address when DHCP is disabled.

Configures the Subnet Mask when DHCP is disabled.

Configures the Default Gateway when DHCP is disabled.

Projector Name Configures the projector name.

SysLocation Configures the location to be referred to when using SNMP.

SysContact Configures the contact information to be referred to when using SNMP.

Mail Settings

Click the [Apply] button to save the settings.

NOTE:

• You can confirm whether the mail settings work correctly using the [Send Test Mail] button.

• If you connect the projector to an existing network, consult a network administrator before setting server

addresses.

Item Description

Send Mail Click the [Enable] check box to use the e-mail function. Configure the conditions for sending

email under [Alert Settings].

SMTP Server IP Address Configures the address of the mail server in IP format.

Sender E-mail address Configures the sender e-mail address. The length of the sender e-mail address can be up to 255

alphanumeric characters.

Recipient E-mail address Configures the e-mail address of up to five recipients. You can also specify [TO] or [CC] for

each address. The length of the recipient e-mail address can be up to 255 alphanumeric charac-

ters.

Alert Settings

Clicking each Alert brings up a dialog box where you can specify that an email be sent to alert the appropriate person-

nel that an error has occurred. Subject can be 255 characters, Text can be 1024 characters.

Item Description

Lamp won’t strike Lamp won’t turn on after 5 attempts.

Lamp Time Over Lamp has exceeded its specified lifetime.

Lamp unexpectedly goes out Lamp failed after it had successfully lit.

Fan failure Fan is not working.

Over temp condition Projector is overheating.

Unidentifiable Error Unknown error.

Lamp Cover Error The lamp door is not installed properly.

Filter Time Over Filter should be cleaned.

Temp Sensor Out Sensor is not working.

Schedule Execution Error A scheduled event did not take place.

Overheating alarm Projector is overheated.

Lamp time custom alarm Allows you to specify when (after how many hours) the lamp alarm message should be sent.

Filter time custom alarm Allows you to specify when (after how many hours) the filter alarm message should be sent.

Schedule Settings

Click the [Apply] button to save the settings.

To add additional functions and events click the [Add] button and set the following items.

Click the [Register] button to add new commands to the Schedule List.

Click the [Delete] button to delete commands from the Schedule list.

Item Description

Daily

Schedule

Schedule List

Configures the daily schedule.

Click the [Enable] check box to enable daily scheduling.

Displays the current daily schedule.

Sunday-Saturday

Schedule

Schedule List

Configures the Sunday through Saturday daily schedules.

Click the [Enable] check box to enable daily scheduling.

Displays the current daily schedule.

Specific date 1-5

Schedule

Month/Day

Schedule List

Configures the specific date (No.1-5) schedule.

Click the [Enable] check box to enable specific date (No.1-5) scheduling.

Configures the Month and date.

Displays the current specific date (No.1-5) schedule.

Item Description

Time Configures the time to execute commands.

Command

Power Parameter

Source Parameter

Configures the commands to be executed.

Configures the parameters for power control.

Configures the parameters for input switching.

Autres manuels pour IN42

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels InFocus Projecteur

InFocus

InFocus LP 815 Manuel d'utilisation et d'entretien

InFocus

InFocus LP260 Manuel d'instructions

InFocus

InFocus LASER PROJECTOR LP 540 Manuel utilisateur

InFocus

InFocus LitePro 210 Manuel utilisateur

InFocus

InFocus LP 650 Manuel utilisateur

InFocus

InFocus LP800 Manuel utilisateur

InFocus

InFocus IN134UST Manuel utilisateur

InFocus

InFocus IN118HDSTa Manuel utilisateur

InFocus

InFocus LP630 Manuel utilisateur

InFocus

InFocus IN5500 Manuel utilisateur

InFocus

InFocus LS700 Manuel utilisateur

InFocus

InFocus X6 Manuel utilisateur

InFocus

InFocus LP 740 LiteMount Manuel utilisateur

InFocus

InFocus C105 Manuel d'utilisation et d'entretien

InFocus

InFocus sp1080 Manuel utilisateur

InFocus

InFocus ScreenPlay 4800 Manuel utilisateur

InFocus

InFocus LP 240 Manuel utilisateur

InFocus

InFocus LP 640 Manuel utilisateur

InFocus

InFocus W1100 Manuel utilisateur

InFocus

InFocus INL14*UST Manuel utilisateur

InFocus

InFocus IN3914 Manuel utilisateur

InFocus

InFocus SP8600 series Manuel utilisateur

InFocus

InFocus IN1124 Manuel utilisateur

InFocus

InFocus Work Big IN32 Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur

Asus

Asus ZenBeam Latte Manuel utilisateur