InFocus CEILING MOUNT LP 1000 SERIES Manuel utilisateur

Installation Guide

LP 1000 Series

Ceiling Mount

Installation Guide

LP 1000 Series

Installationhandbuch zur

Deckenbefestigung

English. . . . . . . . . . . . .1

Deutsch . . . . . . . . . .13

010-0154-00

CEILING MOUNT INSTALLATION GUIDE

The LP 1000 Series LiteMountTM makes it easy to

hang your projector from the ceiling for fixed

installation use in meeting, auditorium and

training room settings.

WARNING: This installa-

tion must be performed in

compliance with your local

building code require-

ments. Local require-

ments take precedence

over any instructions given

in this guide.

You must determine the suitability of this prod-

uct for your intended use and assume all risk

and liability in connection therewith. In Focus

recommends that a professional contractor or

other facilities professional assist you in mount-

ing this device. Be sure to take precautions to

meet all local building codes.

Additional LiteMount Products

In Focus offers two additional LiteMount prod-

ucts that may make your ceiling mount installa-

tion easier.

•The LiteMount False Ceiling Plate

(SP-LTMT-PLT) is designed for suspended ceil-

ings with acoustic tiles. It mounts in your ceil-

ing in place of a ceiling tile. It is pre-drilled

with holes to install the LiteMount brackets.

•The LiteMount Pipe Tubing Extension (SP-

LTMT-EXT) allows you to install the projector

in a room with a high ceiling. With the exten-

sion, you can place the projector from 12”

(30.5) to 46” (117 cm) from the ceiling.

Contact your In Focus dealer to order these prod-

ucts.

Placing the Projector

Refer to the LP 1000 User’s Guide for image dis-

tance, size, and angles of projection to determine

where to install the ceiling mount to meet your

projection needs.

Contents

The LP 1000 Series Ceiling Mount package con-

tains:

NOTE: The maximum

load the ceiling mount can

support is 50 pounds.

1Installation Guide

2ceiling mount base box

dimensions: 11.6” x 10” x 1.5”

(29.5 x 25 x 3.8 cm)

weight: 3.5 lbs (1.6 kg)

3projector mounting bracket

dimensions: 12” x 11.5” x 1.5”

(30.5 x 29.2 x 3.8 cm)

weight: 4.0 lbs (1.8 kg)

4hardware for installing the projector mount-

ing bracket on the projector:

•three (3) 4mm Phillips-head screws

•three (3) 4mm quick release sleeves

•one (1) 10/32 knurled knob screw

5hardware for installing the projector (with

mounting plate) to the base box in the ceiling:

•four (4) 6x12 mm knurled knob screws

•two (2) 6 mm flat washers

•two (2) 10 mm conical spacers

Install the Ceiling Mount Base Box on the Ceil-

ing

WARNING: The ceiling

structure must be able to

support at least 5 times

the weight of the projector

and mounting hardware. If

not, it must be reinforced

according to your local

building codes.

Instructions for installing the ceiling mount on

the LiteMount False Ceiling Plate and the Lite-

Mount Pipe Tubing Extension are given in this

installation guide. If you have not purchased

either of these products, consult a professional

contractor or other facilities professional to

ensure a safe installation.

Please refer to the LiteMount False Ceiling Plate

and LiteMount Pipe Tubing Extension installa-

tion instructions for lists of included hardware.

1Center the ceiling mount base box on the ceil-

ing plate as shown in Figure 1. Make sure the

front of the base box faces forward toward

your projection screen. The front side of the

base box is the only surface without drilled

holes.

2a LiteMount False Ceiling Plate - Align the

holes in the base box with the threaded studs

on the plate. Install the 4 washers and nuts as

shown in Figure 1.

NOTE: Refer to the

Installation Instructions

that came with the Lite-

Mount False Ceiling Plate

and the LiteMount Pipe

Tubing Extension for

important additional infor-

mation.

2b LiteMount Pipe Tubing Extension - Line up

the holes in the base box with the holes in the

plate at the end of the pipe extension. Install

the hardware as shown in Figure 2.

Install the Ceiling Mount Base Box on the Ceiling

3Place the ceiling plate or pipe extension in the

ceiling so that the base box hangs down into

the room.

WARNING: If the

dropped ceiling is an air-

handling plenum, be sure

the cables are plenum-

rated, or install the cables

within conduit.

4Route the projector’s cables through your

ceiling and out the hole in the ceiling

(Figure 7).

FIGURE 1

Install the base box to the LiteMount False Ceiling Plate

make sure this

surface faces front

FIGURE 2

Install the base box to the LiteMount Pipe Tubing Extension

surface faces front

make sure this

Attach the Mounting Plate to the Projector

1Set the projector on a table with the bottom

side up.

CAUTION: Use only the

hardware that is provided

with the LP 1000 Series

Ceiling Mount. Using

different hardware may

damage your projector.

2Insert the 3 screws into the 3 quick release

sleeves (Figure 3).

3Attach the screws and sleeves to the holes in

the projector as shown in Figure 3. Be careful

not to over-tighten the bolts.

4Align the keyholes in the mounting bracket

with the screws in the projector. Slide the

mounting bracket until the quick release

sleeves are at the top of the keyhole slot.

5Attach the 10/32 knurled knob to the projec-

tor in the location shown in Figure 3.

FIGURE 3

Attach the mounting plate to the projector

quick release screws

knurled knob

goes here

quick release screw

Hang the Projector on the Ceiling

1Loosely install the 12 mm knurled knobs, flat

washers, and conical spacers to the 2 hinge

pins on the base box (Figure 4).

FIGURE 4

Attach knurled knobs to the side of the base box

2Make sure your cables are pulled through the

center hole of the base box, then carefully lift

the projector and turn it upside down so the

mounting plate faces the ceiling.

3Insert the projector and mounting bracket

into the base box through the space between

the knurled knobs and base box (Figure 4).

Slide the projector bracket forward until the

knurled knobs rest fully in the vertical slots

and support the projector. Tighten the

knurled knobs completely.

slide projector

bracket here between

the base box and the knurled knob

knurled knob

spacer

washer

Hang the Projector on the Ceiling

IGURE 5

Install the projector in the ceiling base box

4Insert the remaining two 6 mm knurled

knobs through the rear slots in the mounting

bracket and into the holes on the sides of the

base box. Hand-tighten them.

FIGURE 6

Insert the knurled knobs to adjust the angle

Insert knurled knob

through this slot

Autres manuels pour CEILING MOUNT LP 1000 SERIES

Table des matières

Langues :

Autres manuels InFocus Accessoires pour projecteur

InFocus

InFocus SP-CEIL-010 Manuel utilisateur

InFocus

InFocus SP777 Manuel utilisateur

InFocus

InFocus SP-CEIL-012 Manuel utilisateur

InFocus

InFocus SP-LAMP-090 Mode d’emploi

InFocus

InFocus LP70+ Mode d’emploi

InFocus

InFocus SP-LAMP-088 Mode d’emploi

InFocus

InFocus WT96 Manuel utilisateur

InFocus

InFocus SP-CEIL-006 Manuel utilisateur

InFocus

InFocus SP-CEIL-004 Manuel utilisateur

InFocus

InFocus LASER PROJECTOR LP 540 Mode d’emploi

InFocus

InFocus LP 240 Instructions d'utilisation et de sécurité

InFocus

InFocus LP130 Mode d’emploi

InFocus

InFocus LiteProLS Manuel utilisateur

InFocus

InFocus SP-CEIL-UNIV Mode d’emploi

InFocus

InFocus IN2112 Mode d’emploi

InFocus

InFocus SP-LAMP-080 Mode d’emploi

InFocus

InFocus CableWizard SP-CW3 Guide de démarrage rapide

InFocus

InFocus IN42 Mode d’emploi

InFocus

InFocus SP-LAMP-073 Mode d’emploi

InFocus

InFocus LiteShow 4 DB+ Manuel utilisateur

InFocus

InFocus LiteShow network adapter Manuel utilisateur

InFocus

InFocus LP790 Manuel utilisateur

InFocus

InFocus RPM A-C Manuel utilisateur

InFocus

InFocus LP770 Manuel utilisateur

Manuels Accessoires pour projecteur populaires d'autres marques

Optoma

Optoma BX-AL133B Manuel utilisateur

PEERLESS

PEERLESS PE 1120 Mode d’emploi

Osram

Osram SIRIUS HRI Series Manuel

Presentation Switchers

Presentation Switchers PS111 Manuel utilisateur

Kramer

Kramer VIA GO Manuel utilisateur

Yamaha

Yamaha PJL-112 Manuel de la liste des pièces

Swedstyle

Swedstyle CL23AA02ZA25E Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 236CB Manuel du propriétaire

Epson

Epson BrightLink 475Wi Manuel utilisateur

Acer

Acer WP100 Manuel utilisateur

i3 i3board Manuel utilisateur

CHIEF

CHIEF HB-43E Manuel utilisateur

Biamp

Biamp Modena Hub Manuel de service

NEC

NEC MP10RX Manuel utilisateur

Panamorph

Panamorph DCR-S3 Manuel utilisateur

Exact solutions

Exact solutions FRAME-EVO-P10 Manuel utilisateur

CHIEF

CHIEF VCM103S Manuel utilisateur

Sharp

Sharp AN-PH20EZ Manuel utilisateur