Infoblox Trinzic Reporting 1400 Manuel utilisateur

For the Trinzic 1400 Appliances 1

Infoblox Installation Guide

Trinzic Reporting 1400 Appliance

The contents of this document may not be copied or duplicated in any form, in whole or in part, without

the prior written permission of Infoblox, Inc.

The information in this document is subject to change without notice. Infoblox, Inc. shall not be liable

for any damages resulting from technical errors or omissions which may be present in this document, or

from use of this document.

This document is an unpublished work protected by the United States copyright laws and is proprietary

to Infoblox, Inc. Disclosure, copying, reproduction, merger, translation, modification, enhancement, or

use of this document by anyone other than authorized employees, authorized users, or licensees of

Infoblox, Inc. without the prior written consent of Infoblox, Inc. is prohibited.

For Open Source Copyright information, refer to the

Infoblox NIOS Administrator Guide

Trademark Statements

Infoblox, the Infoblox logo, Grid, NIOS, bloxTools, NetMRI, Trinzic and PortIQ are trademarks or

registered trademarks of Infoblox Inc.

All other trademarked names used herein are the properties of their respective owners and are used for

identification purposes only.

Company Information

http://www.infoblox.com/contact/

Product Information

Hardware Models

Trinzic product line: 100, 810, 820, 1410, 1420, 2210, 2220, and Infoblox-4010

Trinzic Reporting: 1400, 2000, 2200, and 4000

Infoblox-4030 DNS Caching Accelerator Appliance

Infoblox-250-A, -550-A, -1050-A, -1550-A, -1552-A, -1852-A, and -2000-A

Network Automation: NetMRI-1102-A, NT-1400, NT-2200, and NT-4000

Document Number: 400-0445-000 Rev. C

Document Updated: August 7, 2013

Warranty Information

Your purchase includes a 90-day software warranty and a one year limited warranty on the Infoblox

appliance, plus an Infoblox Warranty Support Plan and Technical Support. For more information about

Infoblox Warranty information, refer to Infoblox Web site, or contact Infoblox Technical Support.

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Hardware Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

10 Gigabit Ethernet Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

System, Environmental, and Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installing an Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Powering the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Cabling the Appliance to a Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Accessing the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Connecting to the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Specifying Appliance Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Infoblox GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Infoblox CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

System Device Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Managing the Disk Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Hard Disk Drive Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Changing AC Power Supplies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Replaceable Units and SFPs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Infoblox Installation Guide

For the Trinzic Reporting 1400 Appliance

Contents

4 Infoblox Installation Guide

For the Trinzic Reporting 1400 Appliance 5

Introduction

This guide provides an overview of the Trinzic Reporting 1400 network appliance, and explains how to install and

configure the system. You can add the Trinzic Reporting 1400 appliance as a member to the Infoblox Grid and

configure it as a dedicated logging and reporting appliance. Note that you cannot configure the reporting appliance

as an HA pair.

The Infoblox reporting solution automates the collection, analysis, and presentation of core network service data

that assists you in planning and mitigating network outage risks, so you can manage your networks more efficiently.

For more information about the Infoblox reporting solution, refer to the Infoblox NIOS Administrator Guide.

Product Overview

The Trinzic Reporting 1400 is a high performance network appliance that collects data from Infoblox Grid members,

stores the data in the reporting database, and generates reports that provide statistical data about IPAM, DNS,

DHCP, and system activities and performance. It can receive up to 5 GB of data each day. You configure and manage

the Trinzic Reporting 1400 and view reports through an easy-to-use Infoblox GUI that works seamlessly in Windows,

Linux, and Mac environments using standard web browsers. For more information about the Infoblox GUI, refer to

the Infoblox NIOS Administrator Guide.

Key features of the Trinzic Reporting 1400 include the following:

•Support for Grid Management and all administrative features for Infoblox IPAM, DNS, DDNS, DHCP, and

IF-MAP

•High Availability support

•Lights Out Management support

•Replaceable hard disk drives

•Hot-swappable AC power supplies

•Additional AC power supply for a redundant 1+1 configuration

•Alternative system configurations for the support of copper or fiber SFP/SFP+ 1GbE/10GbE interfaces

The Trinzic Reporting 1400 appliance comprises hot-swappable power supplies, replaceable hard disk drives, and

optional network interfaces. It is a Class A digital appliance per FCC regulations, and RoHS and WEEE compliant.

Introduction

6 Infoblox Installation Guide

Hardware Components

The Trinzic Reporting 1400 is a 1-U platform that you can mount in a standard equipment rack using the mounting

brackets and bolts that ship with the appliance. For information about rack mounting, see Rack Mounting on page

13.

Front Panel

The front panel components include the LCD (liquid crystal display) panel and navigation buttons, communication

ports, and LEDs, as shown in Figure 1. For explanations of the Ethernet port LEDs, and console and Ethernet port

connector pin assignments, see Ethernet Port LEDs and Connector Pin Assignments on page 8.

Figure 1 Trinzic Reporting 1400, Front View

The front panel components are described in Table 1.

Table 1 Front Panel Components

Component Description

LCD Panel An LCD screen that displays network settings, software version number, hardware serial

number, and software licenses. You can view and configure the IP address, netmask, and

gateway for the LAN1 port.

Navigation 

Buttons

Buttons that allow you to enter the IP address, subnet mask, and gateway of the LAN1

port through the LCD. Use the Up and Down arrow buttons to specify numbers and the

Left and Right buttons to navigate across digits. You must specify whether to save input

(Accept) or discard it (Cancel). Selecting Cancel at any time returns you to the previous

entry. Entering Accept on the third screen returns you to the system status screen.

USB

Port

LCD Panel

Navigation

Button

Console

Port

MGMT

Port

LAN1

Port

HA Port

(disabled)

LAN2

Port

Power

LED

On/Off

Switch

UID Button

Status

LED

Alarm

LED

IPMI

Port

Hardware Components

For the Trinzic Reporting 1400 Appliance 7

On/Off Switch A power switch to turn the power supply of the appliance on and off. Use a small blunt

object, such as a paper clip, to perform the task.

IPMI Port Dedicated Ethernet port used for LOM (Lights Out Management) with specific releases of

NIOS. Ensure that the IPMI port is properly connected to the network before you configure

LOM through the Infoblox GUI for remote management.

USB Port Reserved for future use.

Console Port A male DB-9 serial port for a console connection to change basic configuration settings

and view basic system functions through the CLI (command line interface). Use the

serial cable and connection adapters that ship with the appliance to make a console

connection to this port.

Only a properly grounded USB-to-Serial dongle is allowed to connect to the serial

console port. If the dongle is connected to a laptop, this laptop must be grounded

properly as well. Failure to do so may result in damage to the serial console port of the

Infoblox appliance. Infoblox is not responsible for such damage.

MGMT Port A 10/100/1000-Mbps gigabit Ethernet port that you can use for appliance management

or DNS service. You can enable the MGMT port and define its use through the GUI after

the initial setup.

HA Port High Availability system failover port. The HA port is disabled. The Trinzic Reporting

1400 does not operate in high availability (HA) mode.

LAN1 Port A 10/100/1000-Mbps gigabit Ethernet port that connects the appliance to the network.

You must use the LAN1 port to set up the appliance initially. It handles all traffic if you do

not enable the MGMT and LAN2 ports. The passive node in an HA pair uses this port to

synchronize the database with the active node.

LAN2 Port A 10/100/1000-Mbps gigabit Ethernet port that connects the appliance to the network.

The LAN2 port is not enabled by default. You can enable the LAN2 port and define its use

through the GUI after the initial setup.

UID Button The unit identification button. When you press the UID button, the LCD panel on the front

panel blinks and the UID LED on the rear panel glows blue. In a rack environment, the UID

feature enables easier location of a server when moving between the front and rear of the

rack. You can also identify the appliance through the Infoblox GUI and CLI command.

Status LED Reserved for future use.

Power LED An LED that glows blue when there is power to the appliance. When it is dark, the

appliance is not receiving power.

Alarm LED Reserved for future use.

Component Description

Introduction

8 Infoblox Installation Guide

Ethernet Port LEDs

To see the link activity and connection speed of an Ethernet port, you can look at its Activity and Link LEDs. Figure 2

shows the status the LEDs convey through their color and illumination (steady glow or blinking).

Figure 2 LEDs

Connector Pin Assignments

An Infoblox appliance has three types of ports on its front panel:

•USB port (reserved for future use)

•Male DB-9 console port

•Three (3) RJ-45 10Base-T/100Base-T/1000Base-T auto-sensing gigabit Ethernet ports (HA interface disabled)

—Available 10-gigabit Ethernet SFP+ configuration or 1-gigabit Ethernet SFP configuration (see 10 Gigabit

Ethernet Support section)

The DB-9 and RJ-45 connector pin assignments are described in Figure 3. The DB-9 pin assignments follow the

EIA232 standard. To make a serial connection from your management system to the console port, use the RJ-45

rollover cable and two female RJ-45-to-female DB-9 adapters that ship with the appliance. RJ-45 pin assignments

follow IEEE 802.3 specifications. All Infoblox Ethernet ports are auto-sensing and automatically adjust to standard

straight-through and cross-over ethernet cables.

Link Activity

Label Color Port Status

Activity Blinking Green Link is Up and Active (SFP+ only)

Steady Yellow Link is up but inactive

Blinking Yellow Link is up and active

Dark Link is down

Link Steady Blue 10000 Mbps (SFP+ only)

Steady Amber 1000 Mbps

Steady Green 100 Mbps

Dark 10 Mbps

Hardware Components

For the Trinzic Reporting 1400 Appliance 9

Figure 3 Connector Pin Assignments

10Base-T Ethernet and 100Base-T fast Ethernet use the same two pairs of wires. The twisted pair of wires

connecting to pins 1 and 2 transmit data, and the twisted pair connecting to pins 3 and 6 receive data. For

1000Base-T connections, all four twisted-pair wires are used for bidirectional traffic.

21 345

6789

Link Activity

78653421

DB-9 Connector Pin Assignments

Pin 10Base-T

100Base-T

Signal

1000Base-T

Signal

T568A

Straight-Through

Wire Color

T568B

Straight-Through

Wire Color

1 Transmit + BI_DA+ White/Green White/Orange

2 Transmit - BI_DA- Green Orange

3 Receive + BI_DB+ White/Orange White/Green

4 (not used) BI_DC+ Blue Blue

5 (not used) BI_DC- White/Blue White/Blue

6 Receive - BI_DB- Orange Green

7 (not used) BI_DD+ White/Brown White/Brown

8 (not used) BI_DD- Brown Brown

Male DB-9 Console Port

RJ-45 Ethernet Ports

Pin Signal Direction

1 (not used)

2Receive Input

3Transmit Output

4DTEReady Output

5 Ground —

6 DCE Ready Input

7 RTS (Request to Send) Output

8 CTS (Clear to Send) Output

9 (not used)

(Looking into the console

port on an Infoblox

appliance)

RJ-45 Connector Pin Assignments

(Looking into RJ-45

ethernet ports on an

Infoblox appliance)

Legend: BI_D = bidirectional; A, B, C, D = wire pairings

Introduction

10 Infoblox Installation Guide

10 Gigabit Ethernet Support

To ensure connectivity to 10 Gigabit networking infrastructure, Infoblox offers versions of the TR-1400 (Trinzic

Reporting appliance) providing three active 10-Gigabit Ethernet (10GbE) interfaces accepting SFP+ transceiver

modules for 10GbE RJ-45 copper or for 10GbE optical connectivity. An example with fiber transceivers is shown in

Figure 4.

Figure 4 Trinzic Reporting 1400, Front View with Four SFP/SFP+ Interfaces (three active)

Infoblox also offers versions of the TR-1400 appliance providing three active 1-Gigabit Ethernet (1GbE) interfaces

that accept SFP transceiver modules for 1GbE optical connectivity.

In select configurations for the Trinzic Reporting 1400, the Infoblox 1GbE SFP or 10GbE SFP+ ports replace the

functionality in the original system MGMT, LAN1, and LAN2 ports, thereby disabling the built-in MGMT, LAN1, and

LAN2 ports. 10GbE support accepts Infoblox-provided SFP+ 10GbE Short Range and Long Range transceivers, Cisco

SFP+ Direct Attach 10GSFP+Cu, or HP HPJ9283B SFP+ Direct Attach 10GSFP+Cu transceivers.

You may mix media types in the set of ports (e.g., copper interfaces and fiber interfaces).

SFP and SFP+ transceivers may be used in a mixed configuration in the 10GbE system. One possible use case

involves installing 10GbE SR SFP+ transceivers in the LAN1 and LAN2 ports for the Trinzic Reporting 1400 appliance,

and installing a 1GbE SFP copper transceiver in the MGMT interface.

See the section Replaceable Units and SFPs, for specific information on part numbers, availability, and device

compatibility.

Rear Panel

The rear panel components include the power connectors, hard disk drives, fans, air vent, and the UID LED, as

shown in Figure 5.

USB

Port

LCD Panel

Navigation

Button

Console

Port

MGMT, LAN1, 

and LAN2 Ports

(disabled with alternate

port configuration)

Power

LED

On/Off

Switch

1GbE or 10GbE interfaces:



MGMT-LAN1-(HA)-LAN2

in order from left to right (HA

disabled)

UID Button

Status

LED

Alarm

LED

IPMI Port for Lights Out Management (LOM)

Table des matières

Autres manuels Infoblox Matériel réseau

Infoblox

Infoblox NT-1400 Manuel utilisateur

Infoblox

Infoblox 2205 Series Manuel utilisateur

Infoblox

Infoblox 1405 Series Manuel utilisateur

Infoblox

Infoblox Trinzic 805 Series Manuel utilisateur

Infoblox

Infoblox 2200 Series Manuel utilisateur

Infoblox

Infoblox SoT-1405 Series Manuel utilisateur

Infoblox

Infoblox 4005 Series Manuel utilisateur

Infoblox

Infoblox Trinzic 100 Manuel utilisateur

Infoblox

Infoblox Infoblox-250-A Manuel utilisateur

Infoblox

Infoblox Trinzic TE-2205 Manuel utilisateur

Infoblox

Infoblox TE-2210 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur