Infinity 5760a Manuel utilisateur

Reference Series

5760a

5761a

6 CHANNEL POWER AMPLIFIER

SERVICE MANUAL

Infinity Systems, Inc.

250 Crossways Park Dr.

Woodbury, New York 11797 Rev2aa10/2005

- CONTENTS -

SPECIFICATIONS ………………………………….……..1

FEATURES/TEST CONDITIONS……..…………………2

CONTROLS/CONNECTIONS………….……..…...…..…3

INSTALLATION………………….……...……..…...…...…5

BASIC TROUBLESHOOTING..…….…….………………7

TYPICAL SYSTEM WIRING..…….…….……………..…8

EXPLODED VIEW/PARTS LIST…………………..….....9

MECHANICAL PARTS LIST…………………………….10

AMPLIFIER BLOCK DIAGRAM…………………………11

P.C.B. DRAWINGS….…………………………………….12

ELECTRICAL PARTS LIST ……………………………. 16

REF 5761a ELECTRICAL PARTS LIST ADDENDUM….……20

IC/TRANSISTOR PINOUTS..……………………….. …..21

REF 5760a SCHEMATICS……………………………....24

REF 5761a SCHEMATICS…………………………..…..28

PACKING…………………………….……………………32

Reference 5760a/5761a Specifications

Output Power: 56W RMS x 4 and107W RMS x 2 channels @ 4 ohms; ≤1% THD + N

80W RMS x 4 and150W RMS x 2 channels @ 2 ohms; ≤1% THD + N

148W RMS x 2 and 287W RMS x 1 channels @ 4 ohms; ≤1% THD + N

Signal-to-noise ratio: 82dBA (reference 1W into 4 ohms)

Dynamic power: 117W channels 1,2,3,4; 163W channels 5,6 @ 2 ohms

Effective damping factor: 6.373 @ 4 ohms

Frequency response: 10Hz – 57kHz channels 1,2,3,4; 10Hz – 302Hz channels 5,6

Maximum input signal: 6.3V

Maximum sensitivity: Reference 5760a - 230mV

Reference 5761a - 75mV

DC Offset <50mV (-50%)

Output regulation: .063dB @ 4 ohms

Idle Current 2.1A

Input Impedance 22kΩ

Max Current Draw 34A @ 4 ohms

88A @ 2 ohms

89.5 @ 4 ohm bridged

Dimensions: 12 x 18 1/2 x 2 11/16” (L x W x D)

(305mm x 470mm x 68mm)

Fuse: 2 x 30A

Infinity continually strives to update and improve existing products, as well as create new ones. The specifications and details in

this and related JBL publications are therefore subject to change without notice.

Power Amplifier Reference 5760a/5761a

Features

•4-Channel Operation

•Advanced MOSFET Oversized Floating Rail Power Supply

•Floating Ground Factory

- Head - Unit Speaker - Level input

•Variable lnput Sensitivity (250mV - 6V)

•Fully Complementary Output Stage with Class-A6 Voltage Amplification

•Gold-plated Power, lnput and Output Connectors

•2-Ohm Stable (Stereo)

Test Conditions and Notes

•All tests to be done, unless otherwise specified, from 10Hz to 47KHz and 302Hz

at 14.4V DC into 4 ohm loads and adjust the units gain so that with a .775 volt

input signal the unit is at Its maximum rated output. All measurements will be

done using an Audio precision system one and the supply voltage.

•An A+ line voltage of 14.4V DC shall be applied to the unit under test for all

measurements unless otherwise specified. The voltage applied to the unit shall

be measured at the power connection on the Amplifier.

•Signal Source

Unless otherwise specified, all tests shall be conducted with the Audio Signal

Generator output configured to be balanced, less than or equal to 50 ohm source

impedance, and floating. The signal source "GND" shall be connected to the

Amplifier PWR GND at the Amplifier.

•Output Load

Unless otherwise specified, all tests shall be conducted with 4 ohm resistive

loads having less than 10% reactive components at any frequency below 47KHz

and 302Hz. Each resistor shall have a value that remains within 1 % while

dissipating the rated output of the unit under test.

•Power Indicator Green LED steadily illuminates for normal operation. Illuminates

up Red LED blinks when protection circuitry is engaged, and during power up.

Power Amplifier Reference 5760a/5761a

•

If the amplifier’s fuse must be replaced, use

only the same type and rating as that of the

original. Do not substitute another kind.

The Reference amplifiers are capable of

delivering high power levels, and require a

reliable connection to the vehicle’s electrical

system in order to perform optimally. See

Figure 1 for connection location. Please

adhere to the following instructions carefully.

GROUND CONNECTION

Connect the amplifier’s Ground (GND) terminal

to a solid point on the vehicle’s metal chassis,

as close to the amplifier as possible. Refer to the

chart below to determine minimum wire-gauge

size. Sand away any paint from this location; use

a star-type-lock washer to secure the connection.

POWER CONNECTION

Connect a wire (see chart at right for appropriate

gauge) directly to the vehicle’s positive battery

terminal, and install an appropriate fuse holder

within 18" of the battery terminal. Do not

install the fuse at this time. Route the wire to

the amplifier’s location, and connect it to the

amplifier’s positive (+12V) terminal. Be sure to

use appropriate grommets whenever routing

wires through the firewall or other sheet metal.

Failure to adequately protect the positive wire

from potential damage may result in a vehicle

fire. When you are done routing and connecting

this wire to the battery and to the amplifier,

you may install the fuse at the battery.The

fuse value should be selected based on total

amplifier-current draw; see chart at right.

REMOTE CONNECTION

Connect the amplifier’s Remote (REMOTE)

terminal to the source unit’s RemoteTurn-On

lead using a minimum of 18-gauge wire. If your

source unit does not have a remote turn-on

connection, connect the amplifier’s (REMOTE)

terminal to the vehicle’s accessory circuit.

WIRE-GAUGE CHART

Amplifier Maximum Minimum

Model Current Draw Wire Gauge

5760a/5761a 87A #8 AWG

These recommendations assume 7' – 10' wire

runs. If your installation differs markedly, you

will need to adjust the wire gauge accordingly.

SPEAKER CONNECTIONS

Refer to the application guides on the pages

that follow. Speaker connections should be

made using a minimum of 16-gauge wire.

HIGH-LEVEL INPUT CONNECTIONS

The 5760a/5761a amplifiers are

equipped with speaker-level inputs that allow

you to add an amplifier to head units that do

not have RCA line outputs.The speaker outputs

for the source unit should be connected to the

amplifier using the supplied connector (square

four-wire plug). Remember to check for proper

polarity.

NOTE: When using the low-level or high-level

inputs, the AUX outputs can be used to pass a

full-range line-level signal to another amplifier.

Figure 2. Speaker-level connector.

POWER CONNECTIONS

Figure 1.Terminal-connection end plate.

HIGH LEVEL

INPUT

Speaker Wires

(spliced)

–

+ WHITE

– WHITE/BLACK

GRAY/BLACK –

GRAY +

5760a

Power Amplifier Reference 5760a/5761a

The amplifier can be configured for 6-channel,

5-channel or 3-channel operation, as shown

in Figures 10 through 12.

INPUT MODE SWITCH:

• Use INT (internal mode) to send a signal from

the front and rear inputs to the subwoofer.

• Use EXT (external mode) when sending a

dedicated signal to the subwoofer inputs; e.g.,

if your source unit has a subwoofer output.

NOTE: For simplicity, Figures 10 through 12 do

not show power, remote and input connections.

NOTE: Minimum speaker impedance for

stereo operation is 2 ohms. Minimum speaker

impedance for bridged operation is 4 ohms.

APPLICATIONS – 5760a/5761a

Figure 10. 6-Channel operation: 5760a/5761a amplifier driving full-range front and rear speakers and a pair of subwoofers.

Figure 11. 5-Channel operation:The same as Figure 10, with the subwoofer output bridged to drive a single 4-ohm subwoofer, providing

the speaker with more power.

Figure 12. 3-Channel operation: 5760a/5761a amplifier configured for 3-channel operation, where all of the channels are bridged for a

subwoofer and a pair of component speakers.

Power Amplifier Reference 5760a/5761a

Initially set the crossover-frequency control

midway. While listening to music, adjust the

crossover for the least perceived distortion from

the speakers, allowing them to reproduce as

much bass as possible.

Systems using a separate subwoofer set the

crossover mode to HP (high pass) for your

full-range speakers. Adjust the crossover

frequency to limit bass, and provide increased

system volume with less distortion.

For subwoofers, choose the highest frequency

that removes vocal information from the sound

of the subwoofer.

NOTE:The subwoofer

output of the 5760a/5761a is low-pass only and does not

have a crossover-mode switch.

SETTING THE CROSSOVER(S)

Determine your system plans and set the

crossover-mode switch accordingly. If your

system design does not include a subwoofer,

set the crossover mode to FLAT and skip to

“Setting Input Sensitivity.”

MODE SWITCH

Flat: Allows a full-range signal through to the

speakers; can be used with larger full-range

speakers such as 6" x 9"s.

HP: Allows a high-pass signal through to

the speakers; should be used with most

loudspeakers (can protect your full-range

speakers from being overdriven with low

frequencies, one cause of speaker damage).

LP: Allows bass to pass through to the speakers;

should be selected when powering subwoofers.

INSTALLATION AND SETUP

Figure 13. Control end panel.

5760a

Power Amplifier Reference 5760a/5761a

Figure 13. Control end panel.

SETTING INPUT SENSITIVITY

1. Initially turn the INPUT LEVEL control(s) to

minimum (counterclockwise).

2. Reconnect the (–) negative lead to the vehi-

cle’s battery. Apply power to the audio system

and play a dynamic music track.

3. On the source unit, increase the volume

control to 3/4 volume. Slowly increase the

INPUT LEVEL control(s) toward three o’clock

until you hear slight distortion in the music.

Then reduce the INPUT LEVEL slightly until

distortion is no longer heard.

NOTE: After the source unit is on, blue LEDs (on

the top panel) will light, indicating the amplifier

is on. If not, check the wiring, especially the

remote connection from the source unit. Also

refer to “Troubleshooting” on the page 7.

REMOTE LEVEL CONTROL (OPTIONAL)

All three Reference subwoofer amplifiers and

the 5760a/5761a amplifier have inputs for an optional

remote level control (100rc).This will allow the

subwoofer level to be adjusted from the listening

position. Connect the optional remote level

control using the RJ-11 jack on the side of the

amplifier. Install the control module in the front

of the vehicle within easy reach of the driver.

Both the underside of the dash and the center

console are suitable locations. Refer to the

mounting instructions accompanying the 100rc.

SETTING THE BASS BOOST

The5760a/5761a are all equipped

with a bass-boost control.This allows you to

enhance the bass output of your system at

50Hz up to 12dB.

AUX OUTPUT

Reference amplifiers 5760a/5761a are equipped

with full-range outputs that can be used to

connect additional amplifiers.

NOTE: When using the low- or high-level inputs,

the AUX outputs can be used to pass a full-range

line-level signal to another amplifier.

STATUS LEDs

Clip: Indicates the amplifier is being overdriven,

and your speakers may be in danger.This

should blink only on musical peaks, and not

be on constantly.

Power: Indicates the amplifier is on.

Protection: Refer to “Troubleshooting” for specific

indications.

Figure 15. LED status.

Power Amplifier Reference 5760a/5761a

•

PROBLEM:

No audio (POWER LED is off).

CAUSE and SOLUTION:

No voltage at BATT+ and/or REM terminals, or

bad or no ground connection. Check voltages

at amplifier terminals with VOM.

•

PROBLEM:

No audio (PROTECT LED flashes every

4 seconds).

CAUSE and SOLUTION:

DC voltage on amplifier output. Amplifier may

need service; see enclosed warranty card for

service information.

•

PROBLEM:

No audio (PROTECT LED is on).

CAUSE and SOLUTION:

Amplifier is overheated. Make sure amplifier

cooling is not blocked at mounting location;

verify that speaker-system impedance is within

specified limits.

•

PROBLEM:

No audio (PROTECT and POWER LEDs flash).

CAUSE and SOLUTION:

Voltage less than 9V on BATT+ connection.

Check vehicle charging system.

•

PROBLEM:

No audio (PROTECT LED is on).

CAUSE and SOLUTION:

Voltage greater than 16V or less than 8.5V on

BATT+ connection. Check vehicle charging

system.

•

PROBLEM:

Distorted audio.

CAUSE and SOLUTION:

Input sensitivity is not set properly, or amplifier

or source unit is defective. Check INPUT LEVEL

setting, or check speaker wires for shorts or

grounds.

•

PROBLEM:

Distorted audio (PROTECT LED flashes).

CAUSE and SOLUTION:

Short circuit in speaker or wire. Remove

speaker leads one at a time to locate shorted

speaker or wire, then repair.

•

PROBLEM:

Music lacks “punch.”

CAUSE and SOLUTION:

Speakers are not connected properly. Check

speaker connections for proper polarity.

TROUBLESHOOTING

Power Amplifier Reference 5760a/5761a

Reference 5760a/5761a

71 2 3 4 5 6 8

Reference 5760a/5761a

Autres manuels pour 5760a

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Infinity Amplificateur

Infinity

Infinity KAPPA K2 Manuel de programmation

Infinity

Infinity Kappa 54a 4-Ch Manuel utilisateur

Infinity

Infinity Kappa 202a Manuel utilisateur

Infinity

Infinity Kappa 255A Manuel utilisateur

Infinity

Infinity Basslink 4SC Manuel utilisateur

Infinity

Infinity 310a Manuel utilisateur

Infinity

Infinity 475a Manuel utilisateur

Infinity

Infinity RS KAPPA PS-8 Manuel utilisateur

Infinity

Infinity Reference 1300A Manuel utilisateur

Infinity

Infinity 310a Manuel utilisateur

Infinity

Infinity Reference 5350A Manuel utilisateur

Infinity

Infinity Basslink 4SC Manuel utilisateur

Infinity

Infinity kappa series Manuel utilisateur

Infinity

Infinity 7520a Manuel utilisateur

Infinity

Infinity K600 Manuel utilisateur

Infinity

Infinity 1211a Manuel utilisateur

Infinity

Infinity Kappa 102a Manuel utilisateur

Infinity

Infinity 7540a Manuel utilisateur

Infinity

Infinity REF-704a Manuel utilisateur

Infinity

Infinity 5760a Manuel utilisateur

Infinity

Infinity Beta Powersource Digital 300 Manuel de programmation

Infinity

Infinity reference series Manuel utilisateur

Infinity

Infinity DPA 275 Manuel de programmation

Infinity

Infinity 311a Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur