IN2CORE ScreenPort SDI+ Manuel utilisateur

ScreenPort SDI+ User Guide version 1.6

Table of Contents

SCREENPORT SDI+ USER GUIDE ............................................................ 2

INTRODUCTION ....................................................................................... 2

FEATURES ................................................................................................ 3

BOX CONTENTS ...................................................................................... 3

CONNECTORS AND CONTROLS ........................................................... 3

POWER OPTIONS .................................................................................... 4

USB-C POWER ADAPTER (INCLUDED) .......................................... 4

BATTERY SLOTS ................................................................................. 4

USB-C POWER BANK ........................................................................ 4

COMPUTER USB ................................................................................. 4

MOUNTING ............................................................................................... 4

GETTING STARTED .................................................................................. 5

CONNECTIONS ........................................................................................ 5

USB ....................................................................................................... 5

ETHERNET ........................................................................................... 5

WI-FI .................................................................................................... 5

ACCESS POINT MODE ....................................................................... 5

SCREENPORT APP ................................................................................. 6

MONITOR ............................................................................................. 6

AUDIO METERS .............................................................................. 6

METADATA ....................................................................................... 6

RECORD ............................................................................................... 6

AUTO-RECORD ............................................................................... 7

BROWSE .............................................................................................. 7

LOAD ................................................................................................ 7

SELECT ............................................................................................ 7

DELETE ............................................................................................ 7

PLAYBACK ........................................................................................... 7

SLIDER ............................................................................................ 7

JOG .................................................................................................. 7

FUNCTIONS ......................................................................................... 7

SDI SOURCE ................................................................................... 8

SETUP .................................................................................................. 8

DEVICE CONTROL .......................................................................... 8

MUTE ............................................................................................... 8

NETWORK ....................................................................................... 8

ADVANCED NETWORK SETTINGS ............................................... 8

AUDIO SETTINGS ........................................................................... 8

QTAKE MONITOR APP ............................................................................ 9

CREATE PROJECT .............................................................................. 9

SELECT SDI INPUT ............................................................................ 9

RECORD SDI INPUT ........................................................................... 9

SET IN/OUT RANGE ........................................................................... 9

PLAYBACK ........................................................................................... 9

FIRMWARE UPDATE ............................................................................... 9

TROUBLESHOOTING ........................................................................... 10

IMPORTANT SAFETY INSTRUCTIONS .............................................. 10

DISPOSAL INFORMATION .................................................................. 11

COMPLIANCE ........................................................................................ 11

July 30, 2021 TABLE OF CONTENTS 1

ScreenPort SDI+ USER GUIDE

INTRODUCTION

Apple devices feature amazing displays that often exceed the quality of dedicated portable and on-

board SDI monitors. In addition to color accuracy, wide gamut, and slim form factor, they oﬀer

responsive touchscreen interface and incredible computing power. But they lack video input.

ScreenPort SDI+ adds video input to iPad, iPhone or Mac and turns it into professional 3G-SDI

monitor capable of capturing up to 1080p60 video feed with your personal portable device.

ScreenPort app provides monitoring, recording, playback and image processing tools unmatched

by most professional monitors.

July 30, 2021 SCREENPORT SDI+ USER GUIDE 2

FEATURES

•Video, audio, metadata monitoring & recording

•SDI embedded or analog audio capture

•Auto-recording using camera SDI ﬂags

•Streaming to remote monitors over internet

•Compatible with QTAKE applications

•Battery powered operation

•Bus-powered operation when using Mac

•Wired and wireless connection to host device

•Predeﬁned and custom frame-lines (coming soon)

•Custom 3D LUT import and processing

•Waveform, vectorscope and histogram analysis (coming soon)

•Focus peaking and customizable false color (coming soon)

•Future-proof design upgradable by ﬁrmware

BOX CONTENTS

ScreenPort SDI+ package includes:

•ScreenPort SDI+ device

•Two WiFi antennas

•Power adapter with international plugs

•USB-C to USB-C power & data cable

•USB-C to Lightning power & data cable

•Cardboard box with protective foam insert

CONNECTORS AND CONTROLS

VIDEO INPUT:

•3G-SDI

AUDIO INPUT:

•3.5mm unbalanced stereo / balanced mono

VIDEO OUTPUT:

•3G-SDI loop-through

DATA PORTS:

•Ethernet

•WiFi (2.4/5.0 GHz, 802.11 a/b/g/n/ac, 2 x 2 MIMO)

•USB-C

July 30, 2021 SCREENPORT SDI+ USER GUIDE 3

POWER:

•5V DC 15W USB-C port

•Dual Sony NP-F style battery mount

CONTROL:

•Software control over USB-C or network

OPERATING FREQUENCY:

•2400 - 2483.5 MHz

•5150 - 5850 MHz

MAX RF OUTPUT POWER:

•< 20dBm EIRP

POWER OPTIONS

ScreenPort SDI+ oﬀers multiple power options for its operation:

USB-C POWER ADAPTER (INCLUDED)

When portability is not an issue, ScreenPort SDI+ can be powered using included AC/DC power

adapter. Moreover, power will be passed to iOS device allowing users to charge it. Power adapter

accepts input of 100-240V, 50/60Hz, 0.55A max and produces output of 5V 3A.

BATTERY SLOTS

The most portable powering option is to use on-board batteries. ScreenPort SDI+ has two battery

slots for Sony NP-F style batteries. Users can opt for original Sony NP-F970 (7.2V, 7800mAh), or

compatible batteries from other brands. Some vendors oﬀer NP-F batteries with lower capacity

and smaller size, which may be more suitable in some cases. Please note that ScreenPort SDI+

cannot charge batteries.

USB-C POWER BANK

More portable powering option is to use external battery or power bank. Compatibility requirement

for power bank is 5V 3A USB-C power output.

COMPUTER USB

When used with computer, USB connection can be used to transfer both data and power, so no

additional power source is needed for ScreenPort SDI+ operation.

MOUNTING

ScreenPort SDI+ contains 3 holes at the bottom side of the device for custom mounting

accessories. Holes will ﬁt 2.2mm self-tapping screws.

July 30, 2021 SCREENPORT SDI+ USER GUIDE 4

GETTING STARTED

Follow these steps to use ScreenPort SDI+ connected via USB cable to iOS device or Mac:

1. Install ScreenPort or QTAKE Monitor application on your iOS device.

2. Connect power source to ScreenPort SDI+ device using USB-C power connector or insert

charged battery into designated slot.

3. Power on ScreenPort SDI+ device using the power switch (status LED will turn white).

Power up sequence takes around 20 seconds.

4. Connect SDI output of the camera to SDI input of the ScreenPort SDI+ using SDI cable

(status LED will turn green if the valid signal is detected).

5. Connect USB-C data port of the ScreenPort SDI+ to your iOS device using data cable.

6. “Trust This Computer?” dialog will appear on your iOS device. Click the “Trust” button.

CONNECTIONS

ScreenPort SDI+ oﬀers multiple ways to connect to a host device.

USB

Connecting ScreenPort USB data port to your host device provides the connection with the highest

bandwidth. This means you can use the best visual quality without worrying your data connection

will drop frames. Downside of the USB interface is the limitation to a single device.

ETHERNET

If you need to connect multiple ScreenPort devices to multiple host devices, ethernet interface is

the solution. When connected to your network with an ethernet cable, signal from each ScreenPort

SDI+ will be available to any device connected to the same network.

WI-FI

Similar to ethernet, Wi-Fi interface is used to connect to your network, but this time wirelessly.

This is the most practical way to stream from ScreenPort SDI+ to monitoring devices. However, it is

also the most fragile way to connect, because data packets can be easily dropped due to lower

signal quality or interference.

ACCESS POINT MODE

Access Point Mode transforms how you can use your ScreenPort device. Instead of relying on

existing Wi-Fi infrastructure, ScreenPort can create its own Wi-Fi network with support for up to 8

wireless clients. This mode requires ﬁrmware 2.54 or higher and ScreenPort app 1.6 or higher.

New devices ship with Access Point Mode enabled by default. To enable Access Point Mode on your

existing ScreenPort device, open the ScreenPort app and tap SETUP, then tap Network and set

Access Point to ON.

When you need to connect to an on-set Wi-Fi network, set Wi-Fi to ON instead. This will

automatically turn Access Point oﬀ, but your settings will be retained for future use.

July 30, 2021 SCREENPORT SDI+ USER GUIDE 5

SCREENPORT APP

ScreenPort SDI+ device can be operated using the ScreenPort application. When connected to iOS

device, ScreenPort SDI+ will be automatically detected. Basic functionality for monitoring,

recording and playback is described below.

MONITOR

Make sure that the LIVE/DISK button located in the top left corner is set to live mode. Viewer will

display the image of the incoming SDI feed. FORMAT label located in the top bar will show the

format of the SDI signal.

AUDIO METERS

If SDI signal contains audio, meters above the image viewer will show the audio level of the live

signal. During playback, meters will show the audio levels of the playback.

METADATA

If the SDI signal contains camera metadata, ScreenPort will extract them and display them in UI

toolbars. Timecode and clip name is located in the bottom part of the screen. Camera and lens

metadata is located in the top part of the screen.

RECORD

When the view is in the LIVE mode, you can tap the white circle icon to initiate recording session.

Incoming video and audio signal will be recorded into a media ﬁle. Tap the record icon again to

July 30, 2021 SCREENPORT SDI+ USER GUIDE 6

ﬁnish recording. If the SDI signal contains timecode, it will be recorded too. In case of missing

timecode, current time of day will be used instead.

AUTO-RECORD

In addition to manual recording, some cameras provide SDI record ﬂags that can be used to

initiate automatic recording. To set the ScreenPort SDI+ to auto-record mode, tap the AUTO REC

button (ARRI and SONY cameras are currently supported).

BROWSE

Tap the VIEW/CLIPS button in the bottom left corner to show the clip browser. Use the DAYS/CLIPS

button in the top left corner to switch between days and clips mode. Each day item represent

folder that contain all clips shot during that day. Tap the day thumbnail to show corresponding

clips.

LOAD

Tap the LOAD/SELECT button to switch between load and selection modes. When the load mode is

active, you can tap the clip thumbnail to load the clip into the viewer.

SELECT

When selection mode is active you can tap or drag your ﬁnger through browser items to select

them. Selected items are marked with blue color.

DELETE

Tap the DELETE button to remove items from the browser and delete corresponding media ﬁles

from the device.

PLAYBACK

Once the clip is loaded into viewer, it can be played back. In addition to realtime playback, there are

two buttons to the right of the PLAY button that allow you to navigate clip frame by frame. Two

buttons to the left of the PLAY button are used to jump to the start or the end of the clip.

SLIDER

Time slider is placed above playback icons and it is used to scrub through the clip. Slider

represents the whole duration of the clip.

JOG

For more precise navigation through the clip, you can drag your ﬁnger horizontally over the viewer.

FUNCTIONS

Switching the INFO/FUNC button to function mode provides access to various functions of the

ScreenPort app.

July 30, 2021 SCREENPORT SDI+ USER GUIDE 7

SDI SOURCE

This ﬁeld is used to identify connected camera. Currently, only ARRI cameras are supported. More

camera vendors will be available via ﬁrmware update.

SETUP

Bottom right corner of the ScreenPort user interface contains TOOLS/SETUP button. Switching this

button to setup mode reveals additional controls.

DEVICE CONTROL

Tap the BITRATE ﬁeld to select the quality of the encoder output. Lower bitrate is useful for wireless

streaming, but if you intend to use wired connection, higher bitrates are available to provide better

image quality. You can further control encoder by setting it to constant (CBR) or variable (VBR)

bitrate. NETWORK ﬁeld is used to connect to existing Wi-Fi network.

MUTE

Live audio can be turned oﬀ using MUTE LIVE button. Use MUTE DISK to mute playback audio.

Muting live audio will not aﬀect audio recording.

NETWORK

Tap the NETWORK ﬁeld to access Wi-Fi and Access Point controls. Enable Wi-Fi to connect to

existing Wi-Fi infrastructure. To create a new Wi-Fi network for client devices to connect to, enable

Access Point instead.

When enabled through the ON/OFF switch, the Wi-Fi section expands to show available Wi-Fi

networks. Allow a few seconds for scanning to complete after enabling. Tap a network to connect

and enter the Wi-Fi password if prompted. The connected Wi-Fi network is shown with a

checkmark on the right side.

When Access Point is enabled, Wi-Fi will automatically turn oﬀ. The Access Point section will

expand to show additional settings. To edit a setting, tap the corresponding row.

To change the access point password, tap the SSID ﬁeld. This will open a dialog where you can set

both SSID and password. To change the SSID only while keeping your current password, leave the

password ﬁeld blank.

ADVANCED NETWORK SETTINGS

To set a manual IP address for your ScreenPort device’s Ethernet or Wi-Fi interface, tap the MORE

button to reveal Advanced Network Settings. Tap the corresponding Conﬁgure IP row and set the

mode to Manual. When set to Manual, you can edit the IP address, subnet, router, and DNS ﬁelds by

tapping any of them.

AUDIO SETTINGS

Tap MORE button to open Audio Settings popover. If your SDI source is using audible timecode, you

can set TC Channel to Left or Right to mute it.

July 30, 2021 SCREENPORT SDI+ USER GUIDE 8

QTAKE MONITOR APP

ScreenPort SDI+ device can be operated using the QTAKE Monitor application. When connected to

iOS device, ScreenPort SDI+ will be automatically detected by the application. Basic functionality

for monitoring, recording and playback is described below.

CREATE PROJECT

QTAKE Monitor is a client application that connects to QTAKE Server. After existing QTAKE project is

downloaded into QTAKE Monitor, the app can be used as a standalone monitor/recorder without

connection to server. Once QTAKE Monitor is re-connected, it will sync media and metadata back

into QTAKE ecosystem.

SELECT SDI INPUT

QTAKE Monitor can display up to 4 views and each view can display diﬀerent content. In order to set

the active view to SDI input, tap the button in the top right corner and select ScreenPort SDI+. If

the device is not listed, refer to troubleshooting page.

RECORD SDI INPUT

When the view is in the LIVE mode, you can tap the bottom middle part of the SDI view to initiate

recording session. Incoming video and audio signal will be recorded into a media ﬁle. Tap the

bottom middle part of the view again to ﬁnish recording. In addition to manual recording, some

cameras support SDI record ﬂags that can be used to initiate automatic recording. To set the

ScreenPort SDI+ to auto-record mode, please refer to Device Settings section.

SET IN/OUT RANGE

Each clip in QTAKE Monitor can have multiple ranges to allow only selected parts of the media ﬁle

to be played back. Use IN and OUT buttons to set the desired range during recording or playback.

PLAYBACK

Tap the REPLAY button in the top bar to play the last recorded clip. Tap the BROWSE button to open

the clip browser and select the clip to be loaded into active view. View mode will change from LIVE

to DISK. Tap the bottom middle part of the active view in the DISK mode to initiate playback. Tap

the top middle part of the view to switch between two playback modes: using ranges or ignoring

ranges. Tap the top left or right view corner to skip to previous or next range. To move the playhead

frame-by-frame, tap the bottom left or right corner.

For more details about advanced functionality please refer to QTAKE Monitor User Guide.

FIRMWARE UPDATE

Firmware update of the ScreenPort SDI+ is a simple procedure. To update your ScreenPort

ﬁrmware, launch the ScreenPort app on an iPhone or iPad connected to the internet, then connect

your ScreenPort device via USB. ScreenPort application will notify you if there is a newer version of

the ﬁrmware available. If you proceed with the update process, new ﬁrmware will be downloaded

July 30, 2021 SCREENPORT SDI+ USER GUIDE 9

Ce manuel convient aux modèles suivants

Table des matières

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur