Impex PREMIER Manuel utilisateur

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Resistance Chart

Warranty

Ordering Parts

Model

PREMIER

Retain This

Manual for

Reference

09-23-02

OWNER'S

MANUAL

MARCY PREMIER

HOME GYM

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: (800) 999-8899 Fax: (626) 961-9966

www.impex-fitness.com

[email protected]

TABLE OF CONTENTS

BEFORE YOU BEGIN....................................................................................……….. 1

IMPORTANT SAFETY NOTICES...................................................................……….. 2

HARDWARE IDENTIFIER.....….....................................................................……….. 3

ASSEMBLY INSTRUCTIONS.........................................................................……….. 4

PARTS LIST…………………………………………………………………………………..16

RESISTANCE CHART………….......................................................................……….17

WARRANTY.................................................................................................………….18

ORDERING PARTS.......................................................................................…………18

BEFORE YOU BEGIN

Thank you for selecting the MARCY PREMIER HOME GYM by IMPEX FITNESS

PRODUCTS. For your safety and benefit, read this manual carefully before using

the machine. As a manufacturer, we are committed to provide you complete

customer satisfaction. If you have any questions, or find there are missing or

damaged parts, we guarantee you complete satisfaction through direct

assistance from our factory. To avoid unnecessary delays, please call our TOO-

FREE customer service number. Our Customer Service Agents will provide

immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST

www.impex-fitness.com

[email protected]m

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply

whenever you operate a piece of exercise equipment. Be sure to read the entire manual

before you assemble or operate your machine. In particular, note the following safety

precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal

symptoms, STOP the workout at once. CONSULT A PHYSICIAN

IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine

near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear

robes or other clothing that could become caught in the machine. Running

or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO

NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or

physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to

properly warm up.

11. Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR

PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF

35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL

INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO

RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY

OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches.

NOTE: It is strongly recommended this machine to be assembled by two or more people to

avoid possible injury.

STEP 1 (See Diagram 1)

A.) Slide two Round Rubber Bumpers (#55) onto the Guide Rods (#14). Align the holes and push

two Guide Rods (#14) into the Rear Stabilizer (#2). Secure each Guide Rod with one M10 x ¾”

Allen Bolt (#72) and ∅¾” Washer (#81) on the bottom.

B.) Install fourteen Weight Plates (#33). To install the plate, hold the plate at an angle and place it

in between the two Guide Rods then drop it down. NOTE: Make sure the groves on the plastic

covers all face up. Insert the Selector Rod (#42) into the center hole on the Plates. Slide the

Selector Stem (#32) onto the Guide Rods from the top. Align the holes and secure the

Selector Stem (#32) to the Selector Rod (#42) with a M10 x 1 ¾” Socket Bolt (#70). Use the

Weight Select Pin (#66) to secure the Plates. Make sure the magnet on the Pin faces up.

C.)It is strongly recommended to spray lubricant such as WD-40 on the two Guide Rods to

minimize friction. Please note this machine comes with 14 plates. You can purchase another 5

more plates (Model No. WK51) in the future to increase the weights.

D.)Attach the Top Socket Assembly (#5) to the top of the Guide Rods. Secure the Assembly to

the Guide Rods with two M10 x ¾” Allen Bolts (#72) and ∅¾” Washers (#81).

DIAGRAM 1

STEP 2 (See Diagram 2)

A.) Attach the Main Base Frame (#1) to the Rear Stabilizer (#2). Secure it with one Bracket

(#41), two M10 x 2 ¾” Carriage Bolts (#79), ∅¾” Washers (#81), and M10 Aircraft Nuts

(#84). Do not tighten the Nuts and Bolts yet.

B.) Attach the bottom of the Vertical Beam (#3) to the Main Base Frame (#1). Secure it with two

M10 x 3 ½” Carriage Bolts (#77), ∅¾” Washers (#81), and M10 Aircraft Nuts (#84). Do not

tighten the Nuts and Bolts yet.

C.)Attach the Butterfly Support Frame (#13) to the front of Vertical Beam (#3). Attach the front

end of Upper Frame (#4) to the back of Vertical Beam. Align the holes and secure them

together with three M10 x 3 ½” Carriage Bolts (#77), ∅¾” Washers (#81), and M10 Aircraft

Nuts (#84).

D.)Attach the rear end of Upper Frame (#4) to the Top Socket Assembly (#5). Secure it with

one Bracket (#41), two M10 x 2 ¾” Carriage Bolts (#79), ∅¾” Washers (#81), and M10

Aircraft Nuts (#84). Securely tighten all the Nuts and Bolts previously installed.

DIAGRAM 2

STEP 3 (See Diagram 3)

A.) Attach the Left and Right Front Presses (#6 & 7) to the pivot on the Main Base Frame (#1).

Secure them together with a M10 x 8 1/8” Axle (#38), two ∅¾” Washers (#81), and two M10

Aircraft Nuts (#84).

B.) Attach the Front Press Bracket (#15) to the Front Presses. Secure it with two M10 x 3 1/8”

Carriage Bolts (#78), ∅¾” Washers (#81), and M10 Aircraft Nuts (#84).

C.) Attach the Seat Pad (#30) to the Seat Incline Adjustment (#12). Secure it with two M8 x 1

5/8” Allen Bolts (#75), and ∅5/8” Washers (#82). Insert the Seat Incline Adjustment into the

opening on the Main Base Frame. Lock the desired incline position with a Lock Knob (#65).

D.) Attach two Foot Plates (#25) to the Main Base Frame (#1). Secure it with two M10 x 2 ¾”

Carriage Bolts (#79), ∅¾” Washers (#81), and M10 Aircraft Nuts (#84). DIAGRAM 3

STEP 4 (See Diagram 4)

A.) Slide one Butterfly Support Bracket (#10) onto the Right Butterfly (#9). Insert the Right

Butterfly into the pivot on the Butterfly Support Frame (#13) from the bottom. Secure it with

one ∅1 ½” Washer (#21), ∅1 3/8” Lock Ring (#57), M6 x 1 5/8” Hex Bolt (#76), and M6

Aircraft Nut (#85).

B.) Attach the Butterfly Arm Pad (#34) to the Right Butterfly. Secure it with two M8 x 2 ¾” Allen

Bolts (#74) and ∅5/8” Washers (#82).

C.)Repeat steps A & B above to install the Left Butterfly (#8).

D.)Attach the Backrest Board (#31) to the Vertical Beam (#3). Secure it with two M8 x 3 ½”

Allen Bolts (#73) and ∅5/8” Washers (#82). DIAGRAM 4

STEP 5 (See Diagram 5)

A.) Attach two ∅1” x ¼” Bushings (#60) to the pivot on the Leg Developer (#11). Attach the

Leg Developer (#11) to the Bracket in front of the Seat. Secure it with one M12 x 3 1/8”

Allen Bolt (#67), two ∅1” Washers (#80) and one M12 Aircraft Nut (#83).

B.) Insert two Foam Roll Tubes (#24) halfway through the holes on the Seat Incline Adjustment

(#12) and Leg Developer (#11). Push four Foam Rolls (#62) onto the Tubes from both

ends. Plug four ∅2 5/8” Foam Roll End Caps (#53) to the ends.

DIAGRAM 5

CABLE LOOP DIAGRAM

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Impex Salle de sport à domicile

Impex

Impex MARCY PRO SM-7362 Manuel utilisateur

Impex

Impex MARCY MXM-5 Manuel utilisateur

Impex

Impex MARCY DIAMOND MD-8870 Manuel utilisateur

Impex

Impex ADBE-10235 Manuel utilisateur

Impex

Impex Marcy MWM-4965SC Manuel utilisateur

Impex

Impex MARCY MWM 800 Manuel utilisateur

Impex

Impex Marcy MCB-999 Manuel utilisateur

Impex

Impex IRON GRIP STRENGTH TSA-410 Manuel utilisateur

Impex

Impex MWB-715N Manuel utilisateur

Impex

Impex MWB-36780B Manuel utilisateur

Impex

Impex MARCY MWB 716 Manuel utilisateur

Impex

Impex IRON GRIP STRENGTH TSA-5682 Manuel utilisateur

Impex

Impex 120727 Manuel utilisateur

Impex

Impex MARCY DIAMOND MD-844 Manuel utilisateur

Impex

Impex MD-4100 Manuel utilisateur

Impex

Impex MARCY CLUB MKM-81010 Manuel utilisateur

Impex

Impex MARCY MWM-990 Manuel utilisateur

Impex

Impex MARCY DIAMOND ELITE MD-3401 Manuel utilisateur

Impex

Impex Marcy SM-8117 Manuel utilisateur

Impex

Impex MARCY DIAMOND ELITE MD-857 Manuel utilisateur

Impex

Impex MARCY MWB-544 Manuel utilisateur

Impex

Impex APEX TSA-499 Manuel utilisateur

Impex

Impex Competitor WM-205 Manuel utilisateur

Impex

Impex MARCY MWB-479 Manuel utilisateur

Manuels Salle de sport à domicile populaires d'autres marques

Horizon Fitness

Horizon Fitness OXFORD 6 Manuel utilisateur

Energetics

Energetics Multi Trainer 5.1 Manuel utilisateur

Matrix

Matrix MG-PL Series Manuel utilisateur

Reebok

Reebok Tbr2i Manuel d'utilisation et d'entretien

Weider

Weider 8300 Hard Drive Manuel utilisateur

Pure Fitness

Pure Fitness 8526HE Manuel utilisateur

Weider

Weider 8700 I Guide de démarrage rapide

Bowflex

Bowflex Sport 001-6961 Manuel utilisateur

NordicTrack

NordicTrack E8200 Competition Bench Guide de démarrage rapide

Weider

Weider WEMC10161 Manuel utilisateur

Body Solid

Body Solid GHYP-345 Manuel utilisateur

Evo

Evo TAHOE 5105 Manuel utilisateur

cardiobull

cardiobull RA17 Manuel utilisateur

ParaBody

ParaBody 40 Manuel utilisateur

JLL

JLL Ventus Pro Air Power Manuel utilisateur

Trojan

Trojan Colorado 370 Manuel utilisateur

Octane Fitness

Octane Fitness xRide xR650 Manuel utilisateur

Precor

Precor Discovery Series Manuel utilisateur