Imperial Kitchen Ventilation C2000 Series Guide d'installation

LNR/5.26.20

Powered Liner—C2000

Installation Instructions

Warranty Information

425 Apollo Street

Brea, CA 92821

www.imperialhoods.com

(800) 851-4192

DO NOT THROW AWAY,

PROPERTY OF THE HOME OWNER!

Unit is to be hardwired.

Adding a Power Cord will void the warranty.

Imperial Cal Products, Inc.

Read Before Starting Installation! Inspect your range hood prior to installing! Any cosmetic

defects must be reported to us prior to installation. Once this hood is installed, ICP will

NOT accept any responsibility for any cosmetic blemishes, scratches or dents in the

Canopy. Save all original packaging if you wish to return for any reason!

FIRST:

Check your local building and electrical codes.

WARNING:

To reduce the risk of fire or electrical shock, Do Not use any two speed motor units with a Solid

State control devise.

CAUTION:

To reduce the risk of fire or personal injury and to properly exhaust air, be sure to duct air to the

outside. DO NOT vent exhaust air into spaces within wall, attics, ceilings, crawl spaces or garages.

For general ventilation use only. Do not use to Exhaust Hazardous or Explosive Materials and

Vapors. When venting to the outside make duct run as short and straight as possible. Avoid

using elbows if at all possible as this will reduce your performance. If elbows are used, we

recommend that the first elbow is 24” from vent opening on the hood and at least 24” between it

and the next elbow. We strongly recommend no more then two 90 degree elbows in any duct run.

Every elbow will decrease the performance and we will not guarantee the effectiveness of the

range hood.

No Performance Warranty when used above BBQ Style Grills.

DO NOT use duct pipe smaller than the outlet duct opening on the hood, this will reduce

performance and void the warranty. DO NOT use flex ducting. Also, use either a Roof Cap or

Wall Cap to end run. Be sure that all joints are taped securely in place. It is essential to have the

proper distance between the bottom of the range hood and the cooking surface below. In most

cases the cooking appliance manufacturers specifications will establish the fire safe minimum

distance required, although there are other factors to consider:

 Local Building Codes

 Cross directional air movements ie: open windows, air conditioning/heating outlets, cooling

fans, etc.

 Overall size of the cooking appliance and surrounding countertop surfaces.

 Range hood model selected.

For best performance distance between cooking surface and the bottom of the hood is 30” and

36”. Check local codes and appliance specifications. Keep in mind, increasing the distance will

decrease the performance.

THERMOSTAT: PS or BP Units ONLY. When cooking surface reaches 130 degrees, the unit will

automatically turn ON to the highest setting and won’t be able to be turned off until the area has

cooled down. For safety, it’s best to have unit on while cooking. (This thermostat will NOT prevent

fires. Fires are most often cause by excessive grease build up.)

TWIN UNITS ONLY - Transitioning two pipes into one is NOT recommended. CFMs are reduced

by 25% and the Performance Warranty will be void.

DISCLAIMER

Imperial assumes no liability regarding the improper installation or misapplication of its products. It

is the installer’s responsibility to check for proper installation. Under no circumstances will Imperial

be liable for any labor charged or travel time incurred for installation of its products. Damage

caused by improper installation is the installers responsibility and Imperial assumes no liability.

WARNING: This product can expose you to certain chemicals, which are known to the State of California to cause

cancer or birth defects or other reproductive harm. For more information to go: www.P65WARNINGS.ca.gov.

Powered Liners Installation Detail:

MODEL MESH FILTERS MODEL BAFFLE FILTERS

C2000SD2 (SD2-NV) C2000BPB

C2000SD4 (SD4-12) C2000PSB

C2000BP (BP1-duct is offset to the left) C2000BP1-TW / TWB (requires 2 duct pipes)

C2000PS C2000PS1-TW / TWB (requires 2 duct pipes)

C2000PS-IS22 (Island Application)

C2000PS-IS28 (Island Application)

1. Line up powered liner to underside

of cabinet or canopy. If unable to

drill directly into cabinet or canopy,

use 4” x 11-1/4” x 3/4” wood blocks

(Figure 1) on the inside of canopy, left

and right side and secure with

screws.

2. Remove Filters of powered liner.

Remove the BLACK tape that holds

the damper blades closed. (Figure 2) (It

is NOT recommended to use two (2)

dampers during installation. You have the option to use an external damper or use the

existing damper already on our unit.)

3. Raise and position powered liner so that the bottom is level with

cabinet and screw through holes on either side of liner. DO NOT

use Motor Mounts as Gripping Points. The duct pipe or pipes

should slip into the Automatic Seal Vent Collar. Additional Duct

Tape can be use if needed.

4. If required, additional mounting at the rear of the unit: Locate wall

studs, drill holes through back of insert to hit studs and attach the

liner to the wall with screws.

5. Island and Peninsula liners should be mounted in the same way

except there will be no rear wall mount.

6. Bring conduit down 4” past the bottom of the liner. NOTE: Top box

for the C2000BP1 shows vent opening Off-Set to the left (facing the hood). The lower

box will be the same size as the other models.

7. Remove junction box cover from C2000. (Be sure to comply with all local electrical and

safety codes.) Units are to be hard wired. It is not recommended to add a

power-cord. Adding a power cord can loosen existing wires inside junction box

causing electrical failure.

8. Hook up electrical wires and secure inside junction box. Replace junction box cover.

Install lights and replace filters. For Baffle filters installation, see baffle installation

page enclosed.

TWIN UNITS ONLY—Transitioning two pipes into one is NOT recommended. CFMs are

reduced by 25% and will VOID the Performance Warranty.

DUCT SIZE INDICATOR - Our standard units have a 7” Round which can be transitioned to

8” Round or 10” Round to increase CFM. To add transition, simply attach transition to the

automatic vent seal color to hold transition in place. Duct tape can be added for extra

security.

See example below:

C2000PS-8 = 8” Round Transition

C2000PS-K = 10” Round Transition

(FIGURE 1)

(FIGURE 2)

Powered Liners Installation Detail Continued:

Figure 1:

Figure one shows the included elbow

transition from 7” diameter round to 3

1/4” x 10” rectangular. This transition is

used to return the filtered air back to

inside the kitchen either through the

canopy face of if applicable the soffit

above. The customer must provide

the appropriate length of straight

7” round ducting that connects the

hood exhaust to the elbow

transition.

Figure 2

Figure two shows a typical air exit

terminating through the canopy face. A

customer supplied, decorative 4” x 10”

used to finish off the cut out opening.

Figure 3

Figure three shows a typical air exit

terminating through the soffit face

directly above the hood canopy.

Again the customer must provide a

4” x 10” register face plate.

Re-Circulating, (Non-Vented) Series: C2000SD2-NV

For use when unable to terminate exhaust ducting to outside the structure.

NOTE: The C2000 NV Unit comes supplied with charcoal filters that will accumulate

the cooking grease and over time decrease the hoods performance. The amount and

style of cooking will dictate how often the filters should be replaced. This type of filter

is designed for replacement only. Contact Imperial to purchase proper replacement

filters.

View from rear of the canopy.

Canopy Exit

Soffit Exit

Included

Not Included

Figure 1

Figure 2

4” x 10” Cover

Face Plate

4” x 10” Cover

Face Plate

Figure 3

Imperial Cal Products, Inc.

To order replace parts or schedule service please call our office at (800) 851-4192

or use our website… www.imperialhoods.com.

PARTS:

When ordering Parts we need the following information:

 Model Number (not serial number) found on UL label inside hood.

 Exact dimensions (in the case of filters)

You can find the model number on the inside of your hood on our UL label. There will be a

several model numbers listed, your model number should have a colored dot or mark next to

it to indicate the exact model you have.

In the case of Filters, we will need the exact dimensions of the filter needed.

Indicate which side has the pull tabs on it. Filters are not a warranty replacement part. With

care your filters should last many years.

Payment on Parts is handled one of three ways: PrePaid (you send a check prior to our

Shipping), call with credit card information, VISA or MasterCard, COD or Cash if you decide

to “Will Call”. Our Will Call hours are 8:30 to 3:30, Monday through Friday.

SERVICE:

When calling in for Service we need the following information:

 Model Number (not serial number)

 Proof of Purchase

 Name of company you purchased the hood through.

 Name & Phone number of the person to contact to set up the service call.

 Full address of the location where service is to be done.

Warranty is Seven Years, Parts and Labor.

Maintenance & Warranty Information

RANGE HOOD CLEANING—When cleaning a painted hood, wash it with mild, soapy

water ONLY! Wipe the hood thoroughly with clean water and dry with soft cloth. When

cleaning Stainless Steel use a cleaner specifically for Stainless Steel. Always rub with the

grain using non-abrasive cleaning materials. AVOID detergents, drying agents,

disinfectants or cleaning products in aerosol cans. NEVER use abrasive scouring powders

on your hood! Some cleaning chemicals may damage the hood finish!

BAFFLE FILTER CLEANING—To remove Baffle Filters, remove center panel by pulling

panel toward the front of the hood, lift up to remove. Move filters to the center of the hood,

pull baffle towards the front of the hood and lift out. To remove grease tray, slide tray to the

top of the hood and lift out. Grease will accumulate in grease tray. Clean with hot water and

polish with stainless steel cleaner.

SLIM BAFFLE & ALUMINUM MESH FILTER CLEANING

Clean filters often for the best performance. How often depends on cooking style. Use hot

water and a degreaser to clean. May be used in the dishwasher through the RINSE

cycle ONLY. Some detergents may discolor filters. For Slim Baffles polish baffle side

with stainless steel cleaner.

‘Clean Fan, Filter and Grease Laden

Surfaces FREQUENTLY

LIGHTING

 LED BULB—PAR 20 FLOOD LAMP—DIMMABLE.

Warning: Do not use any bulbs that are not instructed by manufacturer.

Your Imperial Warranty: KEEP your receipt. Proof of original purchase date

is needed to obtain service under warranty.

Deluxe Units: Seven Year Limited Warranty, Parts and Labor in the Continental

USA. Parts only outside the United States.

For seven years from date of original purchase, we will provide parts and service labor in

your home to repair or replace any part of the hood that fails due to a manufacturing defect.

Call for service at (800) 851-4192

NOTE: Service companies will perform Warranty Service, Monday through Friday from

7 a.m.—4: p.m. The service company will call and schedule a date and time with a 4 hour

window. If the service company arrives at your location, during the scheduled date and

time, and no one is home, you will be charged a trip charge by the service company for a

return service call.

ITEMS IMPERIAL WILL NOT PAY FOR

1. Service calls to correct the installation of your appliance, to instruct you how to use your

appliance, to replace or repair house fuses or the correct housing wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs or filters.

3. Repairs when your appliance is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper

installation, installation not in accordance with electrical or plumbing codes.

5. Replacement parts or repair costs for units operated outside the United States.

6. Pickup and delivery. This appliance is designed to be repaired in the home.

7. Repairs to parts or systems resulting from unauthorized modification made to the appliance.

8. Expenses for travel and transportation for product service in remote locations.

9. The removal and reinstallation of your appliance if it is installed in an inaccessible location or

is not installed in accordance the published installation instructions.

10. Replacement parts or repair labor costs when the appliance is used in a country other than

the country in which it was purchased.

SAFETY INSTRUCTIONS

Read and Save These Instructions

Warning: To reduce the risk of fire, electrical shock or injury to persons, observe the

following:

A. Use this unit only in the manner intended by the manufacturer. If you have any questions,

contact the manufacturer. Before servicing or cleaning unit, switch power off at service

panel and lock Service Disconnecting Means to prevent power from being switched on

accidentally. When the Service Disconnecting Means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Warning: To reduce the risk of a range top grease fire:

A. Never leave surface units unattended at high settings. Boil-overs cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

B. Always turn hood ON when cooking at high heat or when Flambéing foods (i.e. Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fans or

filters.

D. Use proper pan size. Always use cookware appropriate for the size of the surface

element.

Warning: To reduce the risk of injury to persons in the event of a range top

grease fire, observe the following:

A. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, then turn off the

burner. BE CAREFUL TO PREVENT BURNS. If flames do not go out immediately,

EVACUATE AND CALL THE FIRE DEPARTMENT.

B. NEVER PICK UP A FLAMING PAN - you may be badly burned.

C. DO NOT USE WATER, including wet dishcloths or towels, violent steam explosion will

result.

D. Use an extinguisher ONLY if:

 You know you have a Class ABC extinguisher and you already Know how to use it.

 The fire is small and contained in the area where it started.

 The fire department is being called.

 You can fight the fire with your back to an exit.

Warning: To reduce the risk of fire, electrical shock or injury to persons, observe the

following:

A. Installation work and electrical wiring must be done by a qualified person or persons in

accordance with all applicable codes and standards, including fire-rated construction.

B. Sufficient air is needed for proper combustion and exhausting of gases through the flue of

fuel burning equipment to prevent back drafting. Follow the heating equipment manu-

facturer’s guideline and safety standards such as those published by the National Fire

Protection Association (NFPA), and the American society for Heating, Refrigeration & Air

conditioning Engineers (ASHRAE), and the local code authorities.

C. When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other

hidden

utilities.

D. Ducted fans must always be vented to the outdoors.

Warning: To reduce risk of fire, use only Smooth Metal Ducting!

Liner alimenté—C2000

Instructions d'installation

Informations sur la garantie

425 Rue Apollo

Brea CA 92821

www.imperialhoods.com

(800) 851-4192

PROPRIÉTÉ DU PROPRIÉTAIRE DE LA MAISON,

NE PAS JETER !

Impériale Cal Products, Inc.

Lire avant de commencer l'Installation ! Inspecter avant d'installer votre hotte de

cuisinière ! Les défauts cosmétiques doivent nous être signalés avant l'installation.

Une fois cette hotte est installée, ICP n'acceptera aucune responsabilité pour toute

les imperfections cosmétiques, rayures ou bosses dans la canopée. Enregistrer

tous les emballages d'origine si vous voulez retourner pour n'importe

quelle raison !

TOUT D'ABORD :

Vérifiez vos locales de construction et les codes de l'électricité.

AVERTISSEMENT :

Pour réduire le risque d'incendie ou d'électrocution, ne pas utiliser n'importe quelle unité

de moteur à deux vitesses avec un Solid State devise de contrôle.

MISE EN GARDE :

Pour réduire le risque d'incendie ou de lésions corporelles et pour bien évacuer l'air,

n'oubliez pas d'évacuer l'air vers l'extérieur. N'évacuez pas l'air dans des espaces dans le

mur, les greniers, les plafonds, les espaces confinés ou les garages. Pour une utilisation

de ventilation générale seulement. N’utilisez pas pour épuiser dangereux ou des matières

explosives et les vapeurs. Lorsque la décharge à l'extérieur faire conduit tourner aussi

court et aussi droit que possible. Évitez d'utiliser des coudes si possible. Si les coudes

sont utilisés, nous recommandons que le premier coude est 24 "d'ouverture sur le capot

(minimum de 12 po) et au moins 24" entre elle et le coude du prochain. Nous ne recom-

mandons vivement aucuns plus puis exécutez deux coudes de 90 degrés dans n'importe

quel canal. Aucune garantie de Performance lors de l'utilisation au-dessus des

grilles de Style BBQ.

N'utilisez pas conduit plus petite que la sortie du conduit d'ouverture sur le capot, cela

réduira les performances et annuler la garantie. N'utilisez pas de conduits flexibles. Aussi,

utilisez soit un capuchon de toit ou de mur à la course de fin. N'oubliez pas que tous les

joints sont scellés

solidement en place. Il est essentiel d'avoir la bonne distance entre le bas de la hotte et la

table de cuisson ci-dessous. Dans la plupart des cas, les spécifications de fabricant

appareil cuisson établira la distance minimale sécuritaire de feu requise, bien qu'il existe

d'autres facteurs à considérer : LocalBâtimentCodes Traverser c'est à dire les

mouvements d'air directionnel : ouvrir les fenêtres, prises d'air conditionné/chauffage,

refroidissement, ventilateurs, etc.. Taille globale de l'appareil de cuisson et les surfaces

environnantes de comptoir. Hotte d'aspiration modèle sélectionné.

Pour la meilleure distance de performance entre la surface et le fond de la hotte de

cuisine est 30 "et 36". Consulter les codes locaux et spécifications de l'appareil. Gardez à

l'esprit, augmente la distance diminue les performances.

TWIN unités seulement- Phase de transition de deux tuyaux en un seul n'est pas

recommandé. SSFC est réduits de 25 % et la garantie de Performance seront annulée.

WARNING: This product can expose you to certain chemicals, which are known to the State of California to cause

cancer or birth defects or other reproductive harm. For more information to go: www.P65WARNINGS.ca.gov.

Détail d'Installation Liners alimenté :

MODEL MESH FILTERS MODEL BAFFLE FILTERS

C2000SD2 (SD2-NV) C2000BPB

C2000SD4 (SD4-12) C2000PSB

C2000BP (BP1-duct is offset to the left) C2000BP1-TW / TWB (requires 2 duct pipes)

C2000PS C2000PS1-TW / TWB (requires 2 duct pipes)

C2000PS-IS22 (Island Application)

C2000PS-IS28 (Island Application)

1 Line up doublure alimenté pour dessous d’armoire ou de la verrière. Si incapable de

percer directement dans l’armoire ou

verrière, utilisez les blocs de bois 4 "x

11-1/4" x 3/4" (Figure 1) à l’intérieur de

la verrière, gauche et droite côté

et fixer avec les vis.

2 Supprimer des filtres de doublure

sous tension. Supprimer le Noir

ruban adhésif qui maintient les

lames clapet fermé. (Figure 2) (Il n’est

pas recommandé d’utiliser deux 2

amortisseurs lors de l’installation.

Vous avez la possibilité d’utiliser un clapet externe ou utiliser le clapet existant déjà sur

notre unité.)

3 Relance et position propulsé doublure afin que le fond est à niveau avec armoire et vis

dans les trous de chaque côté de la membrane. Ne pas utiliser

des supports moteur comme Points de préhension. Le

conduit ou les tuyaux doit glisser dans le collet de l’évent

automatique joint. Supplémentaires du ruban adhésif peut

être utilisé si nécessaire.

4 Si nécessaire, supplémentaires de montage à l’arrière de

l’appareil : localiser les montants du mur, percez les trous arrière

de puissance suffisante pour frapper les goujons et fixez la toile

au mur avec des vis.

5 Doublures de l’île et la péninsule doivent être montés de la même

manière, sauf qu’il n’y aura pas de montage paroi arrière.

6 Conduit Bring down 4" passé le fond de la cocotte. Remarque : Top box pour le

C2000BP1 montre ouverture décalée vers la gauche (en face de la hotte). La

zone inférieure sera la même taille que les autres modèles.

7 Supprimer la boîte de jonction couvercle de C2000. (Veillez à respecter tous les codes

de sécurité et les locaux d’électricité). Unités doivent être câblés dur. Il n’est

pas recommandé d’ajouter un cordon d’alimentation. Ajout d’un cordon

d’alimentation peut se dégager des fils existants à l’intérieur de la boîte

de jonction, causant des pannes électriques.

8 Boîte de jonction crochet vers le haut de fils électriques et sécurisé à l’intérieur.

Replacer le couvercle de la boîte de jonction. Installer des lumières et remplacer les

filtres. Pour déflecteur installation des filtres, voir page installation d’un

déflecteur.

Deux unités seulement — Transition deux tuyaux en une seule est pas recommandé.

SSFC sont réduits de 25 % et sera vide la garantie Performance.

Indicateur de taille de conduit -Nos unités standards ont un 7" rond qui peuvent être

passés à 8" rond ou 10" rond pour augmenter pi3/min.

(FIGURE 1)

(FIGURE 2)

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Imperial Kitchen Ventilation hotte de ventilation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WHN2042PSSB-8-SS Guide d'installation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation 3000 Series Guide d'installation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation G3000SD2 Guide d'installation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WH1900B-8 Guide d'installation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation 30NV Manuel utilisateur

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WHP1900 Series Guide d'installation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WH1900-10 Guide d'installation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WH1900 Series Guide d'installation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WHP1930BP1-BL Manuel utilisateur

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WH1948PSR-SS Guide d'installation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WHN2000 Guide d'installation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation Slim Line Series Guide d'installation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation 2000PS-IS-8-SS Guide d'installation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WH2000 Guide d'installation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation C2000B-8 Guide d'installation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation 1942E Guide d'installation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation C2060PS1TWBSS Guide d'installation

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation Powered Liner-C2000 Guide d'installation

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Zephyr

Zephyr Spruce AK9834BS Guide d'installation

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Smeg

Smeg KSEV97X Manuel utilisateur