IMC 4 Series Manuel utilisateur

VR60 GLASS FROSTERS

INSTALLATION AND OPERATING MANUAL

PLEASE LEAVE WITH OPERATOR

VR60 Glass Froster

Series 4

Imperial Machine Company Limited

Unit 1, Abbey Road

Wrexham Industrial Estate

Wrexham LL13 9RF

Tel: +44 (0)1978 661155

Fax: +44 (0)1978 729990

Service Fax: +44 (0)1978 667766

Spares Fax: +44 (0)1978 667759

E-mail: info@imco.co.uk

Website: www.imco.co.uk

A34/055 R5 ECN 8917 January 2020

VR60 –GLASS FROSTER 2

EC DECLARATION OF CONFORMITY

(Guarantee of Production Quality)

We, Imperial Machine Company Limited of:

Unit 1, Abbey Road, Wrexham Industrial Estate, Wrexham, LL13 9RF

Declare under our sole responsibility that the following products

VR60

as described in the attached technical documentation, are in conformity with the protection

requirements of the Electromagnetic Compatibility Directive 2014/30/EU and manufactured in

accordance with harmonised standards EN 61000-6-1: 2001 Immunity and EN 61000-6-3: 2007

Emissions (plus product specific standards).

They also satisfy the essential health and safety requirements of the Low Voltage Directive

2014/95/EC and are manufactured in accordance with standards BS EN 60335-1 and BS EN

60335-24, and the relevant requirements of the Pressure Equipment Directive 2014/68/EU.

Approved by : E.Plumb, Engineering Manager -

Date: January 2020

VR60 –GLASS FROSTER 3

INDEX

INDEX ................................................................................................................... 3

WARRANTY ......................................................................................................... 4

DELIVERY ............................................................................................................ 4

SAMPLE RATING LABEL.................................................................................... 5

INTRODUCTION................................................................................................... 5

INSTALLATION .................................................................................................... 7

CHANGING AN LED LIGHT FITTING.................................................................. 8

CHANGING OPTION DOOR HANDLES .............................................................. 9

ELECTRICITY SUPPLY CONNECTION............................................................. 10

COMMISSIONING .............................................................................................. 10

CHANGING THE CONTROLLER SET POINT ................................................... 11

USING YOUR GLASS FROSTER ...................................................................... 11

ECO BUTTON FUNCTION ................................................................................. 12

CLEANING.......................................................................................................... 13

CHANGING SHELF POSITION .......................................................................... 13

MAINTENANCE.................................................................................................. 14

DO’S AND DON’TS ............................................................................................ 15

ORDERING SPARE PARTS............................................................................... 16

END OF LIFE DISPOSAL................................................................................... 16

MATERIAL CONTENT........................................................................................ 16

WIRING DIAGRAM............................................................................................. 17

SPARES LIST DRAWING 1 ............................................................................... 18

SPARES LIST DRAWING 2 ............................................................................... 19

SPARES LIST ..................................................................................................... 20

NOTES................................................................................................................ 21

VR60

–

GLASS FROSTER

WARRANTY

These Glass Froster’s are guaranteed by IMC for 2 years from the date of

purchase from IMC, or from one of its stockists, dealers or distributors. The

guarantee is limited to the replacement of faulty parts or products and excludes

any consequential loss or expense incurred by the purchaser. Defects which

arise from faulty installation, inadequate maintenance, incorrect use, connection

to the wrong electricity supply, or fair wear and tear, are not covered by the

guarantee.

The guarantee applies in this form to installations within the United Kingdom.

Export units carry 2 years “parts only”warranty.

Please observe these instructions carefully.

DELIVERY

The packaged machine consists of:

VR60 Glass Froster containing:

Shelf (Full size)

Shelf (base ½ size)

Shelf clips

Sets of keys

Instruction Booklet 1

Please notify both the carrier and the supplier within three days of receipt if

anything is missing or damaged.

Check that the correct machine has been supplied and that the voltage, marked

on the rating plate, is suitable for the supply available. The rating plate is

located internally on the right hand side of the unit.

VR60

–

GLASS FROSTER

SAMPLE RATING LABEL

INTRODUCTION

The VR60 range is a back-bar or under-bar glass froster designed for the

frosting and storage of glasses.

The following quantity of standard pint glasses can be held in each unit:

Glass Froster Capacity

(Standard Pint Size Glass)

VR60 (900h x 600w x 500d)

VR60 (800h x 600w x 500d)

VR60

–

GLASS FROSTER

VR60 Dimensions:

MODEL

900mm

500

900

60 8

500

X mm

Y mm

600mm

VR60

–

GLASS FROSTER

INSTALLATION

For the Installer

These Instructions contain important information designed to help the user

obtain the maximum benefit from their investment in an IMC VR60 Glass

Froster.

Please read them carefully before starting work, and consult with the supplier in

the event of any queries.

Be sure to leave this Instruction Manual with the user after installation of the

machine is complete.

Procedure

WARNING

The following table shows the weight and the minimum quantity of

people required to lift each unit:

Glass Froster Net Weight Quantity of

People

VR60 (all variants) 57.5 kg (max) 2

Install the unit on a flat and level floor.

Ensure a minimum 10mm clearance to either side of the unit, there is to be

a 20mm clearance at the top and 60mm clearance at the back.

Do not install the unit close to a heat source such as a radiator or a warm air

outlet.

Ensure that the unit is standing level by adjusting the feet on the base of the

unit.

The unit has an automatic defrost cycle and evaporates all the condensate

water without the need for a drainage system.

NOTE!

It is important to install the Glass Froster on a flat surface. This

ensures that the doors are level. Adjustment is provided via the

feet, to enable the installer to level the cabinet. Engineer Call-

outs in order to level Glass Frosters, will not be covered under

warranty.

VR60

–

GLASS FROSTER

CHANGING AN LED LIGHT FITTING

The cabinet interior is illuminated by a LED light strip fitting located at the front

of the top inner panel.

To change the light assembly:

·Ensure the mains power to the unit has been turned off.

·Open the front cabinet door(s).

·Unscrew the screws holding the LED assembly in place.

·Carefully lower the LED assembly down and disconnect the 2 wires from the

unit.

·The LED light assembly should now be free to fully remove from the unit.

·To fit the replacement unit.

·Place the new LED light assembly inside the unit, re connect the 2 wires

from the unit to the new LED light assembly.

·Re fit the LED light assembly inside the unit by using the screws.

·Re-connect the mains power and ensure the light illuminates by means of

the ECO switch.

Fixing

Screws

Fixing

Screws LED Light

Assembly

crews

LED Light

Assembly

crews

VR60

–

GLASS FROSTER

CHANGING OPTION DOOR HANDLES

The option doors have 2 types of handle which are removed and fitted in the

same way. However, the long handle option has 4 screws and the short handle

option has 2 screws.

To change or move a handle:

·Open the front cabinet door(s)

·Using a phillips screw driver, unscrew all the screws that secure the

handle in place, then remove the handle and retain the screws

·Place new / same handle in desired position (see orientations below)

·Fix the handle back to the door with the same / supplied screws

·New / additional handles are available from IMC

VR60

–

GLASS FROSTER

ELECTRICITY SUPPLY CONNECTION

Position the unit in the chosen site. The electricity supply connection should be

made to a power outlet socket or isolator mounted on the wall close to the

machine. This socket or isolator must be accessible once the machine is

installed. Before connecting, check that the voltage shown on the rating label is

correct for the electricity supply you have available. If the plug does not fit your

sockets or a longer lead is required, changes must be made by an approved

electrician.

NOTE: The plug is fitted with a 10amp fuse.

The plug fuse cover must be refitted when changing the fuse. In the event of

losing the fuse cover the plug must NOT be used until a replacement fuse cover

has been obtained and fitted or the plug replaced.

WARNING: This machine must be earthed

Should the supply cord become damaged then a replacement must be fitted by

an approved electrician. The IEE Codes of Practice must be observed.

The wires in the mains lead are coloured in accordance with the following code

Green and yellow Earth

Blue Neutral

Brown Live

COMMISSIONING

Before using a bottle cooler for the first time, the interior should be wiped out

with a clean damp cloth.

Allow the machine to stand for 1 hour to allow the refrigerant to settle. Plug in

and switch on at the wall socket. There is no separate switch to turn on the

machine. The compressor will start running less than one minute after the

supply is switched on.

Check that the “ECO”button is not depressed i.e. the blue logo is illuminated.

(See relevant section for the operation of this “ECO”function)

Check that the light is working. If a fluorescent light is fitted, the switch is

located inside the cabinet, on the left hand end of the top inner panel.

Run the unit empty, and check that cold air is being circulated within the

cabinet.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels IMC Congélateur

IMC

IMC MISTRAL M60 Manuel utilisateur

IMC

IMC MR60 Manuel utilisateur

IMC

IMC MISTRAL TC60 Guide de l'utilisateur

IMC

IMC Frostar FR60 Guide d'installation

Manuels Congélateur populaires d'autres marques

Siemens

Siemens GU..D SERIES Manuel utilisateur

Omcan

Omcan FR-CN-0155 Manuel utilisateur

Beko

Beko FNE290E24W Manuel utilisateur

Electrolux

Electrolux ARCTIS G 8 60 50-6I Manuel utilisateur

Electrolux

Electrolux EUF2042AOX Manuel utilisateur

Dometic

Dometic CoolFreeze CFX95DZ Manuel utilisateur

Electrolux

Electrolux EUF7000W1 Manuel utilisateur

Polar Electro

Polar Electro CT330 Manuel utilisateur

MPM

MPM MPM-145-SK Series Manuel utilisateur

SAF

SAF PRESTOTIG 200AC/DC Guide rapide

Zanussi

Zanussi ZFT11407WA Manuel utilisateur

AEG

AEG A63190GT Manuel utilisateur

AEG

AEG A81000TNW0 Manuel utilisateur

Matsui

Matsui MUC50S15E Manuel utilisateur

NEFF

NEFF G4344X8 Manuel utilisateur

Frigidaire

Frigidaire FV 1246 H Manuel utilisateur

Frigidaire

Frigidaire FFC13K1AW Manuel utilisateur

Electrolux

Electrolux EU 2400C Manuel utilisateur