IKarus Mach 3 Mode d’emploi

Mach 3

#160760

Norbert Grüntjens

Ikarus Modellflugsport, Inh. Norbert Grüntjens

Im Webertal 22, 78713 Schramberg-Waldm./Germany

Tel. 0(049)7402 929190 Fax. 0(049)7402 929150

5/2000

Mach 3 kit contents

Mach 3 building instruction

The MACH 3 is a Slow and Park flyer that shows fantastic

flightcharacteristicsduetoitslightweight.Itcanbeflownat

extremespeedseitherverysloworreallyfast.

Funisguaranteedsinceit`sfeature make aerobatics are no

problemsevenwhenthereislittlespace.

Additional items (not

included in the set)

Motor-/Gear set

No. 160611

Battery pack No. 160607

CA glue , Epoxid glue Knife, scissors, tongs

Micro controller (No. 160533)

Mini receiver (No. 160565)

Micro servos (No. 720367)

Buildingthefuselage

Mark the aluminium boom (acc. to the picture) in distances

of 90 mm and 275 mm from the tip of the boom for adhering

thechassisatthisplaceslateron.

Roughen the boom where the chassis is going to be affixed

totheboomandfixthechassis-wirewithCAGlue.

Nowwindthecarbon fibre firmly around thechassisandthe

boom.Afterwardsmoisten the material with CAGlue and let

itbecomehard.

Assembly

Please read the following instructions carefully before you

starttobuilttheMach3.

Attention:Takeyourtimetoreadtheinstructionsfortheglue

usedfortheconstructionofyournewflightobject:

Cyanoacrylateglue

This glue needs to be kept away from children. No contact

should be allowed for children. It works in seconds and

gluesskinandeyes.Aftereye-contactpleaserinsecarefully

and see a doctor immediately. Do not use with Styrofoam

parts.

UHU-Por

Thisisacontacttypeglue.Coverbothsurfacesmeanttobe

glued together as thinly as possible with the glue and leave

to try 10-60 minutes before carefully joining the surfaces

together.

9m0 m

2 5mm7

Tip

Wingassembly

Glue the halves of the wing together using contact glue.

Reinforcewithself-adhesivetape.

Bevel the rudder about 30°.Attach the rudder as shown on

thewingusingtape.

Glue the rudder reinforcement onto the interior of the

rudder.

Markthepositionoftherudder horns and drill a 3 mm whole

at this point. Glue the rudder horns in connection with the

rudderhorn–disk. Now the completedwingcanbeglued to

the fuselage stick. Check the balance by keeping an eye on

theedgesofbothwings.

Slide the wheel onto the

nave and both on the

chassiswire.

Then bend the wire as

close to the nave as

possible.

Tape

Glue

Tape

Wing halves

Use a sharp knife to work on the downward side of the

wings in the area of the chassis reinforcement, so that the

wingscanlaysmoothlyonthefuselage.

Rudder

Wing Tape

Tape

30°

bevel

Reinforcements

Fixpoint

Reinforcements

Approx.

5mm

If the Pico Servos (No. 720367) are used, there should be a

cutting in the body of 19 x 22 mm in a distance of 145 mm

from the end-ledge. In this cutting the servos need to be

integrated using glue. Use CA Glue to fix a fork-head each

onthecarbonfibresticks.Roughentheplacewheretheglue

hastobeused.

Screw the two remaining fork-heads on the solder sleeves

until the middle of the thread. Attach the fork-heads to the

horns of the rudder and adjust the rudder that the rudder

deflection points upwards 4 mm at the deepest point. If

necessary shorten the carbon-fibre sticks that they reach

into the solder-sleeves 1 cm. Use CA-Glue to attach the

stickstothesleeves.

Forkhead (1)

Forkhead (2)

Solder sleeve

Carbon fibre sticks

145 mm

Cutting

19*22mm

Approx

4mm

Work on

Drill an opening for the fixation stick of the fuselage with a 3

mm borer. Attach this at a 90 degree angle by using glue.

Dependingonwhatkindofbatteryisintendedtobeused,cut

an opening for the cable-binder that is thought to affix the

battery.

Insertingtheengine

Slide the engine-socle onto the fuselage stick that was

roughened and glue it with CA-glue. The axis of the engine

should be in a 2° angle downwards which is predetermined

by using the Ikarus Engine Set (No. 160611). Please

connecttheEngineMicroSpeedControler2000.

Cut the body and the cabin cover with scissors and a knife

along the marked lines. Smooth the edges afterwards for

using fine sandpaper. Please leave some room for this

whencuttingalongthelines.

230mm from the stern, make a 5 mm boring. Insert the

rubber cover here, fix the fuselage here. Glue the side

rudder on the fuselage as marked on the body of the plane.

At the end glue the cabin cover and decorate the model

accordingtothe pictureonthecardboard.Therivets andtin

decorationaremadebyusinganinkpen.

230 m

Rubber cover

2°

Mark the centre of gravity and hold the model at this point

on a fingertip. It should be horizontal now. If this is not the

case,usethebatteriestobalanceuntilthecorrecthorizontal

positionisachieved.

175mm

Pre-flightchecks

Now switch on the transmitter, and switch the gear stick to

lowthrottleposition.Switchtheflightbatteryon.

Now test the rudder and the mixture, a delta mixer is

necessary.(checkthemanualofyourtransmitter)

Now pose yourself behind the model and test the altitude

rudder. Both rudders should move upwards. If you test the

direction and give right, the right rudder should move

upwardswhereastheleftruddershouldpointdownwards.

Control the angle of the rudder movement. 15mm deflection

areagoodresult.

All RC-components need to be fully tested before trying the

firstpracticeflight.Especially thereachofthecomponentsis

of importance. Test this by switching on the transmitter, then

the batteries and then move 30 m away from the model with

inserted transmitter antenna. There should be no

malfunction.If this is not the case, check forthecause of the

irritation.Are the batteries recharged?Are the right quartz in

thereceiverandtransmitter?

The first start can be tried from hand or an even ground. Do

not use the steering extensively since the model reacts with

sensitivity.

Autres manuels iKarus Jouet

iKarus

iKarus SHOCK FLYER Sukhoi SU 27 Mode d’emploi

iKarus

iKarus LAMA Manuel utilisateur

iKarus

iKarus WIZARD Mode d’emploi

iKarus

iKarus Dragstair Manuel utilisateur

iKarus

iKarus Rumpler Taube Manuel utilisateur

iKarus

iKarus ECO 7 Sport Manuel utilisateur

iKarus

iKarus LAMA Guide de démarrage rapide

iKarus

iKarus ECO 8 Manuel utilisateur

iKarus

iKarus Storm-III Manuel utilisateur

iKarus

iKarus Mini Copter Manuel utilisateur

iKarus

iKarus SHOCK FLYER Mode d’emploi

iKarus

iKarus ECO 7 Sport Manuel utilisateur

iKarus

iKarus EXTRemA 330S Mode d’emploi

iKarus

iKarus PRO Piccolo Mode d’emploi

iKarus

iKarus Bleriot III Manuel utilisateur

iKarus

iKarus PPS-4D Manuel utilisateur

iKarus

iKarus ECO8 Royal 6081001 Mode d’emploi

iKarus

iKarus ECO Piccolo V2 Manuel utilisateur

iKarus

iKarus Eco16 Manuel utilisateur

iKarus

iKarus Dragstair Manuel d'utilisation

iKarus

iKarus FUN Piccolo Mode d’emploi

iKarus

iKarus LAMA Manuel utilisateur

iKarus

iKarus craftair Manuel utilisateur

iKarus

iKarus AIRWOLF Manuel utilisateur

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur

Mattel

Mattel HOTWHEELS DWL04 Manuel utilisateur

iKarus Mach 3 Mode d’emploi

Manuels Jouet populaires d'autres marques