IgniteNet SunSpot N300 Manuel utilisateur
– 1 –
Quick Start Guide
Indoor Stand-Alone Access Point
SunSpot™ AC1200 and SunSpot™ N300
The SunSpot N300 and the SunSpot AC1200 are single- and dual-band concurrent
access points (AP’s) respectively. The units are designed to be operated either
laying on a desk or mounted on a wall or ceiling. The box includes a mounting plate
for attaching the AP to the ceiling. The access point can be powered either by the
universal power supply included in the box or through an Ethernet cable
connection from an optional PoE switch.
The Indoor Stand-Alone Access Points include these models:
◆SS-AC1200 — dual-band w/integrated 2.4 GHz and 5 GHz antennas
◆SS-N300 — single-band w/integrated 2.4 GHz antenna
Note:
For Safety and Regulatory information, refer to the Safety and Regulatory
Information document included with the AP.
www.ignitenet.com
– 2 –
Quick Start Guide
Follow the steps in this guide to install the AP in your network.
Caution:
The planning and installation of the AP requires professional personnel
that are trained in the installation of radio transmitting equipment. The user is
responsible for compliance with local regulations concerning items such as
antenna power for instance. Therefore, it is recommended to consult a professional
contractor knowledgeable in local radio regulations prior to equipment
installation.
1. Unpack the AP Unpack the AP and check the package contents.
◆Outdoor Stand-Alone Access Point
SunSpot AC1200 or SunSpot N300
◆Ceiling-mounting plate
◆A bag with 4 screw anchors and 4 screws as well as 4 rubber feet.
◆Universal power supply — either US, Continental Europe or UK
◆Documentation —Quick Start Guide and Regulatory and Safety Information
2. Mount the AP Using the AP on a desk
If the AP is not mounted on a wall or on the ceiling, simply place the provided
rubber feet on the AP.
1
1
1
1
Desk operation
Place the provided rubber feet to
cover the four screw holes.
1
– 3 –
Quick Start Guide
Mounting the AP on a wall
Mount the unit on a wall using the provided screws.
Mounting the AP on the ceiling
If the room is equipped with a suspended ceiling, the mounting plate provided in
the box can be used to attach the AP to the metal grid of the ceiling.
Wall Mounting
Drill holes in the wall at an horizontal distance of
116 mm from each other. This distance
corresponds to the distance between the
mounting holes on the back of the AP.
Use the screw plugs and screws provided in the
box of the AP or verify that the size of the head of
the screws is small enough to fit through the
mounting holes (< 7 mm).
Screw the screws in the wall until they stick out
just enough to enter the mounting holes.
Adjust the AP on the screws and then down in its
final position.
2 2
1
1
1
1
2
1
1
2
2
3
Suspended Ceiling Mounting
Press the retention clips of the mounting plate
against the ceiling bar.
Rotate the plate until the bar snaps into place.
Slide the rails on the back of the AP along the
sides of the ceiling mounting plate.
1
2
3
– 4 –
Quick Start Guide
The ceiling mounting plate supports two different kinds of ceiling bars. The
position illustrated above is for 15 mm bars. Use the other position at a 90 degrees
angle for 24.5 mm bars.
3. Connect Cables Connect Ethernet cable to the 1000BASE-T (PoE) port on the unit.
4. Connect Power The AP can be powered either by the power supply provided in the box or by an
optional 802.3af/at PoE switch.
Powering the AP with a power supply
Connect Category 5e or better cable to the
leftmost RJ-45 port.
This 1000BASE-T (PoE) port is named ETH0.
Connect the other end of this cable to a
LAN switch.
(Optional) Connect local LAN devices to
any of the other RJ-45 ports of the
connector panel using Category 5 or better
cable.
These 100BASE-T ports are named ETH1
and ETH2.
1
2
1
2
Connect the cable from the power supply to
the DC connector of the AP.
Connect the power supply to a nearby AC
power source (100-240 VAC, 50/60 Hz).
1
1
– 5 –
Quick Start Guide
Powering the AP with a PoE switch (optional)
Simply connect the Ethernet cable from the ETH0 port of the AP to a PoE port on a
802.3af/at compliant switch. Make sure that this switch is connected to the LAN.
Note
:
Connecting the Ethernet cable from the AP to the injector module powers
on the unit.
5. Verify AP Operation Verify basic AP operation by checking the system LEDs.
the ETH0 port LED on/blinking green, and the 2.4GHz/5GHz wireless LED on/
blinking green (2.4 GHz) or blue (5 GHz).
ETH0 (PoE) port link/activity LED.
2.4GHz/5GHz link/activity LED.
1
2
1
2
– 6 –
Quick Start Guide
6. Connect to the Web
User Interface
The stand-alone APs offer a web-based management interface for the
configuration of all the unit’s features.
You can make initial configuration changes by connecting a PC directly to the AP’s
ETH1 RJ-45 port. The AP has a default management IP address of 192.168.2.1 and a
subnet mask of 255.255.255.0. You must set your PC IP address to be on the same
subnet as the AP (that is, the PC and AP addresses must both start 192.168.2.x).
Log in to the web interface using the default
settings:
◆Login Name — root
◆Password — admin123
For more information on stand-alone AP
configuration using the web interface, refer
to the User Guide.
AC1200 & AC866 Series QSG
JCF140912-R02
– 7 –
Quick Start Guide
Hardware Specifications
Item Specification
Chassis
Size (H x W x D:) 200 x 200 x 39 mm (7.87 x 7.87 x 1.53 inches)
Weight 626 g (1.38 lb)
Temperature Operating: -20 °C to 65 °C (-4 °F to 149 °F)
Storage: -30 °C to 80 °C (-22 °F to 176 °F)
Humidity Operating: 15% to 95% (non-condensing)
Waterproof/Dustproof IP55
Network Interfaces
Ports ETH0 (PoE) RJ-45 Port: 1000BASE-T, passive PoE
ETH1 RJ-45 Port: 100BASE-TX
ETH2 RJ-45 Port: 100BASE-TX
2.4 GHz Radio IEEE 802.11b/g/n
5 GHz Radio IEEE 802.11a/n/ac
Radio Frequencies 2412 ~ 2472 MHz
5745 ~ 5825 MHz (China)
5180 ~ 5320 MHz (ETSI)
5500 ~ 5700 MHz (ETSI)
Power Supply
Power Supply 100-240 VAC, 50-60 Hz, auto-sensing
PoE Input Power 12 VDC, 2 A
Power Consumption 24 W maximum
Regulatory Compliances
Radio EN 300 328 V1.8.1:2012
EN 301 893 V1.7.1:2012
EN 301 489-1 V1.9.2 (2011-09)
EN 301 489-7 V1.3.1:2005
FCC Part 15C 15.247/15.207 (2.4-2.4835GHz, 5.725-5.850GHz)
FCC Part 15E 15.407 (5.150GHz-5.250GHz)
Emissions EN 55022 2010+AC:2011
EN 61000-3-2 2006+A1:2009+A2:2009
FCC Class B Part 15
Immunity EN 55024 : 2010
EN 61000-4-2 : 2009
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels IgniteNet Point d'accès sans fil
IgniteNet
IgniteNet Spark AC Wave2 Mini Manuel utilisateur
IgniteNet
IgniteNet ML-60-35 Manuel utilisateur
IgniteNet
IgniteNet SunSpot AC Wave2 Manuel utilisateur
IgniteNet
IgniteNet Spark AC Wave2 Manuel utilisateur
IgniteNet
IgniteNet Spark AC750 Manuel utilisateur
IgniteNet
IgniteNet MetroLinq2.5 ML2.5-60-35 Manuel utilisateur
IgniteNet
IgniteNet Spark SP-W2M-AC1200 Manuel utilisateur
IgniteNet
IgniteNet SkyFire AC1200 Manuel utilisateur
IgniteNet
IgniteNet SunSpot AC1200 Manuel utilisateur
IgniteNet
IgniteNet Spark IR-AC750 Manuel utilisateur
Manuels Point d'accès sans fil populaires d'autres marques
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur
Ubiquiti
Ubiquiti NanoStation NSM2 Manuel utilisateur
Cisco
Cisco Aironet 1550 Series Manuel utilisateur
Aruba
Aruba IAP-335 Manuel utilisateur
Advantek Networks
Advantek Networks AWN-AP-54MR Manuel utilisateur
IP-COM
IP-COM AP355 Manuel utilisateur
