Instruction Manual G-Baby/ GCG-Baby G-2c/GCG-2c G-6c/ GCG-6c
8 9Innovative DisplayWorks, Inc.
MAINTENANCE
Cleaning
• Before cleaning the appliance, always
remember to unplug it.
• Unplug the cooler at the electrical outlet;
never pull the service cord.
• Do not use sharp or pointed objects for
cleaning.
• Clean the inside cabinet of the cooler with
a clean damp cloth. Avoid damage by
using non-abrasive and non-fl ammable
cleaning products.
• Clean the condenser at least once a
month with a vacuum cleaner or a brush to
eliminate the dust accumulation.
Light Replacement
• Unplug the cooler before removing the
LED light strip.
• Remove the screws.
• Remove the light cover gently.
• Take out the LED light strip.
• Replace the used strip with new equivalent
light strip.
• Install the light cover and tighten the
screws.
• Plug in the cooler.
Power Failure
• Please minimize the frequency of opening
the door during a power failure.
• If your cooler is unused for an extended
period of time, unplug, empty, and clean
your cooler and keep the door open to
avoid condensation, formation of mold, or
odors.
Moving The Cooler
• Empty the unit.
• Secure all loose parts inside the cooler.
• Tape the door shut.
• During transportation, make sure that the
cooler is in an upright position.
Drip Pan
• During normal compressor cycle, water will
drain into the drain pan and evaporate.
• To clean, gently pull the drain pan towards
you and remove. Slowly reinstall it after
cleaning.
LEVELING
• Place the cooler on a dry, level surface.
• Unit must be leveled for proper operation, this will help
prevent condensation.
• The cooler should be leveled front to back and side to side
with a level.
LEVELING LEG CLEANING
• Use a cloth to clean
leveling legs.
UNDER CABINET CLEANING
• Before starting, unplug the
power cord to make sure
the cooler is powered off.
• Once nished, plug the
cooler power cord back in.
Main Leveling Legs
• Tilt the cooler back and
use cloth to clean the
bottom of cabinet.
Front Supporting Leg
• Use the cloth to also clean
the compressor base
board. Then level the
cooler.
SHELVING INSTALLATION
Shelf clips should be level so
shelf lays fl at.
Shelves are secured in place
with zip ties. Cut zip ties to
adjust shelves as desired.
Securely insert shelf clips into
pilasters.
(Maximum load per shelf is lbs/ kg)
Display refrigerators can be loaded within the shelf dimensions from the front
to back side. They can also be loaded in any space from the bottom to the top
interior cabinet. Do not allow product to block the evaporator fan cover because
the evaporator fan helps the cooler to ventilate properly.
Display refrigerators can be loaded within the shelf dimensions from the front
to back side. They can also be loaded in any space from the bottom to the top
interior cabinet. Do not allow product to block the evaporator fan cover because
the evaporator fan helps the cooler to ventilate properly.
Display refrigerators can be loaded within the shelf dimensions from the front
to back side. They can also be loaded in any space from the bottom to the top
interior cabinet. Do not allow product to block the evaporator fan cover because
the evaporator fan helps the cooler to ventilate properly.
Display refrigerators can be loaded within the shelf dimensions from the front
to back side. They can also be loaded in any space from the bottom to the top
interior cabinet. Do not allow product to block the evaporator fan cover because
the evaporator fan helps the cooler to ventilate properly.
Display refrigerators can be loaded within the shelf dimensions from the front
to back side. They can also be loaded in any space from the bottom to the top
interior cabinet. Do not allow product to block the evaporator fan cover because
the evaporator fan helps the cooler to ventilate properly.
[Model(s)] maximum load per shelf is lbs/ kg
[Model(s)] maximum load per shelf is lbs/ kg
[Model(s)] maximum load per shelf is lbs/ kg
[Model(s)] maximum load per shelf is lbs/ kg
[Model(s)] maximum load per shelf is lbs/ kg
[Model(s)] maximum load per shelf is lbs/ kg
[Model(s)] maximum load per shelf is lbs/ kg
[Model(s)] maximum load per shelf is lbs/ kg
[Model(s)] maximum load per shelf is lbs/ kg
[Model(s)] maximum load per shelf is lbs/ kg
[Model(s)] maximum load per shelf is lbs/ kg
[Model(s)] maximum load per shelf is lbs/ kg
[Model(s)] maximum load per shelf is lbs/ kg
[Model(s)] maximum load per shelf is lbs/ kg
Display refrigerators can be loaded within the shelf dimensions from the front
to back side. They can also be loaded in any space from the bottom to the top
interior cabinet. Do not allow product to block the evaporator fan cover because
the evaporator fan helps the cooler to ventilate properly.
G-Baby/GCG-Baby maximum load per shelf is lbs/ kg
G-2c/GCG2c maximum load per shelf is 15.43 lbs/ 7 kg
G-6c/GCG-6c maximum load per shelf is 55 lbs/ 24.94 kg
