IDTECK Star RF10 Manuel utilisateur

User’s Manual

Proximity Card Reader

User’s Manual

Table of Contents

1. Important Safety Instructions.................................................. 4

2. General............................................................................................... 5

3. Features ............................................................................................. 5

4. Specification .................................................................................... 6

5. Identifying Supplied Parts......................................................... 6

6. Installation........................................................................................ 7

7. Wire Color Table of the RF 10 / RF 20................................. 7

8. Wire Connection to Access Controller ................................. 8

9. Operation.......................................................................................... 8

10. FCC Registration Information ................................................ 9

11. Warranty Policy and Limitation of Liability ................... 10

12. How to Make RMA Request (After Sales Service)...... 11

User’s Manual

1. Important Safety Instructions

The description below is to keep user’s safety and prevent any product damage. Please fully

read these instructions and use the product properly.

Danger: This symbol indicates that incorrect handling of the product may result

in serious injury or death.

Warning: This symbol indicates that incorrect handling of the product may

result in injury or property damage.

- Only use the standard voltage (DC +12V / 350mA).

- If the product emits smoke or smells, stop using the product. Unplug the product from DC power

source and contact nearest service center.

- Do not install the product in a place subject to humidity, dust (metallic dust) or splashing water

(raindrops).

- Do not install the product in a place not meeting the operating humidity and temperature specified

in the specification.

- Do not install the product with tools such as driver in hand when power is being supplied.

- Do not drop liquid onto the product such as water and give the product a severe shock.

- Do not place magnetic objects near the product.

- Do not replace the wiring cables installed by experts.

- Do not use the product under direct sunlight or in a heat-producing place such as a place near a

heating apparatuses.

- If you want to relocate the installed product, turn power off and then move and reinstall it.

- Do not use flammable sprays or objects near the product.

- Do not let anyone but the manger touch the product except using it for normal purpose.

- If liquid has been spilled on the product, unplug it first.

- Do not clean the product with water. Clean gently with dry cloth or towel.

- Do not use chemicals such as benzene, thinner or acetone for cleaning.

CAUTIONS ABOUT INSTALLATION

CAUTIONS ABOUT POWER

CAUTIONS ABOUT USAGE

CAUTIONS ABOUT CLEANING

User’s Manual

2. General

The Star RF10/20 is an elegant looking proximity reader. It can be easily mounted on door frame

(mullion) or flat wall surface. The Star RF10/20 is a credible product with epoxy potting that enables

you to install it outside.

3. Features

- 125KHz Proximity Card Reader

- PSK Modulation (IDTECK Format)

- Read Range: Up to 4 inches (10cm) (In case of IDC170)

- User Format Available

- Output Format: 26bit Wiegand (default) / RS232 (Optional, Simultaneous output of 26bit Wiegand

and RS232)

- Easy to Install on Metal Door Frame or Mullion or Wall Mount

- LED Control Port and Buzzer Control Port

- Solid Epoxy Potted

- Waterproof & Dustproof (IP65 / IP66)

- Lifetime warranty

- Reverse Polarity Protection

- Compatible Controller: iCON100, iTDC, iMDC, IDTECK Standalone Controller, Third Party Controller

(Using 26bit Wiegand)

User’s Manual

4. Specification

Model

RF10

RF20

CPU

8bit Microprocessor

Read Range

IDK50 / IMC125: Up to 2 inches (5cm)

IDC80: Up to 2.8 inches (7cm)

IDC170: Up to 4 inches (10cm)

Reading Time (Card)

30ms

Power / Current

DC 12V / Max.150mA

Input Port

2ea (External LED Control, External Buzzer Control)

Output Format

26bit Wiegand (Default), RS232 (Optional)

LED Indicator / Beeper

2 Color LED (Red and Green) / Piezo Buzzer

Operating Temperature

-35to +65C ( -31to +149F )

Operating Humidity

10% to 90% relative humidity non-condensing

Color / Material

Dark Pearl Gray / Polycarbonate

Weight /

Dimension (W x H x T)

133.5g (0.296lbs) /

45.5mm x 124mm x 24mm

(1.79” x 4.76” x 0.91”)

143g (0.32lbs) /

75.5mm x 124mm x 24mm

(2.97”x 4.88” x 0.94”)

Waterproof & Dustproof

IP65 / IP66

Certification

FCC, CE, KCC(MIC)

5. Identifying Supplied Parts

Please unpack and check the contents of the box.

Reader Module RF10 or RF20 Bezel User’s Manual

(1ea) (1ea) (1ea)

3.5*40 Screw 3.5*25 Screw 6.0*30 Anchor Bolt

(2ea) (2ea) (2ea)

User’s Manual

6. Installation

6-1. Mullion/Wall Mount

Drill two 3.5*40 or 3.5*25 screw holes in the designated location of the wall 83.8mm(3.3") apart

vertically and drill one 12mm(0.47”) hole for the controller cable in the center of the two holes.

6-2. Pass the reader cable through the center hole and install the reader module by using two 3.5*40

or 3.5*25 screws.

6-3. Put bezel on the reader module and push bezel

7. Wire Color Table of the RF 10 / RF 20

SIGNAL

COLOR

Main Power (+12V)

Red

Power Ground (GND)

Black

Not Connect

Orange

Wiegand Data 0 Out

Green

Wiegand Data 1 Out

White

Buzzer Control In

Blue

LED Control In

Yellow

RS232 (TX)

Brown

* Please cut out tail connector before installation.

User’s Manual

8. Wire Connection to Controller

9. Operation

9-1. If power is supplied to the RF10/20, red light is turned on and the reader goes into standby.

9-2. Present a RF card close to the product until you hear beep sound. The LED of RF10/20 turns into

green simultaneously and the reader sends card data to the controller. And then, LED turns into

red and the reader goes into standby again for next reading.

9-3. LED Control

You can change LED color setting oppositely by connecting LED Control Input wire (Yellow wire)

to Power GND. In this case, Green light is turned on when the reader is on standby and once you

present RF card, the LED of RF10/20 turns into red simultaneously. And then, it turns into green

again for next reading.

9-4. Buzzer Control

If Buzzer Control Input wire (Blue wire) is connected to Power GND, buzzer generates sound

continuously. Cards cannot be read during the buzzer is operating.

Access Controller

Main Power (+12V)

Power Ground (GND)

Not Connect

Wiegand Data 0 Out

Wiegand Data 1 Out

Buzzer Control In

LED Control In

RS232 (TX)

RED

BLACK

ORANGE

GREEN

WHITE

BLUE

YELLOW

BROWN

User’s Manual

10. FCC Registration Information

FCC REQUIREMENTS PART 15

Caution: Any changes or modifications in construction of this device which are not expressly

approved by the responsible for compliance could void the user's authority to operate the equipment.

NOTE: This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions;

1. This device may not cause harmful interface, and

2. This device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class A Digital Device,

pursuant to Part 15 of the FCC Rules. These limits are designed to this equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined

by turning the radio or television off and on, the user is encouraged to try to correct interference by

one or more of the following measures.

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on another circuit.

4. Consult the dealer or an experienced radio/TV technician for help.

User’s Manual

11. Warranty Policy and Limitation of Liability

IDTECK warrants this product against defects in material and workmanship for the period specified

below from the date of purchase under normal customer use. This Warranty doesn’t apply: 1) to any

product which has been dismantled without authorization of IDTECK or/and has a damaged or detached

QC label on its back side; 2) to any losses, defects, or damages caused by improper testing, operation,

installation, maintenance, modification, alteration, or adjustment; 3) to any product with a damaged or

faded serial number on it; or 4) to any losses, defects, or damages caused by lightning or other

electrical discharge, natural disaster, misuse, accident or neglect.

This Limited Warranty is in lieu of all other warranties, obligations, or liabilities on the part of IDTECK,

and IDTECK DISCLAIMS ANY AND ALL WARRANTY, WHETHER EXPRESS OR IMPLIED, OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.IDTECK does not, and cannot,

know who is present, what property is located, where this product will be used; it would be extremely

difficult to determine the actual damages that may result from a failure of the product to perform as

anticipated; and the low price of this product is based upon the nature of the product provided and the

limited liability that IDTECK assumes. IDTECK IS NOT RESPONSIBLE FOR ANY PERSONAL INJURY,

PROPERTY DAMAGE OR LOSS, DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES,

OR OTHER LOSS, AND IDTECK’S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE

PURCHASE PRICE OF THE PRODUCT.

To obtain repair or replacement under the terms of this warranty, visit IDTECK’s Website

(http://www.idteck.com) and place an online RMA request. After an RMA code is issued, return the

product along with the RMA authorization code.

>> Warranty Period

Product Category

Warranty Period

RF CARDS (ACTIVE TYPE)

1 year

FINGERPRINT MODULE / SENSOR

RF READERS (WITHOUT EPOXY POTTING)

2 years

STANDALONE CONTROLLERS

CONTROL PANELS

FINGERPRINT READERS

RF READERS (WITH EPOXY POTTING)

Lifetime

RF CARDS (PASSIVE TYPE)

User’s Manual

12. How to Make RMA Request (After Sales Service)

To make the RMA request, the product must be initially registered on IDTECK webpage. After

registering the product, send it to IDTECK RMA Center.

Please follow the instructions below:

1. Please register the RMA request via IDTECK webpage.

: www.idteck.com “Support & Download” “Online RMA” “RMA REQUEST”

(Please refer to the IDTECK webpage for more details.)

2. RMA Code will be issued after the RMA Center reviews the RMA request form.

3. Enclose the product along with the RMA Code and send it to IDTECK RMA Center.

(Product without RMA Code is not accepted.)

If you have any questions or problems regarding the RMA services, please contact us using the contact

information below. Friendly representatives at IDTECK are always standing by to provide the best after

sales services.

IDTECK Headquarter

5F, Ace Techno Tower B/D, 684-1, Deungchon-Dong,

Gangseo-Gu, Seoul, 157-030, Korea

Tel: +82 2 2659 0055

Fax: +82 2 2659 0086

E-mail: [email protected]

Website: www.idteck.com

E-Training Center: http://www.idtecktraining.com

IDTECK Production Facility and RMA Center

3F, 10/10-1/10-2, Dodang-Dong,

Weonmi-Gu, Bucheon-Si, Gyeonggi-Do 420-130, Korea

Tel: +82 2 2659 0055

Fax: +82 2 2659 0086

E-mail: [email protected]

Website: www.idteck.com

E-Training Center: http://www.idtecktraining.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels IDTECK Lecteur de cartes

IDTECK

IDTECK Star RFK505 Manuel utilisateur

IDTECK

IDTECK SR10/30V Manuel utilisateur

IDTECK

IDTECK SR30 Manuel utilisateur

IDTECK

IDTECK Star FINGER006 Manuel utilisateur

IDTECK

IDTECK STAR RF70 Manuel utilisateur

IDTECK

IDTECK Star SR10 Manuel utilisateur

IDTECK

IDTECK Star RFK505 Manuel utilisateur

IDTECK

IDTECK Star RFK101 Manuel utilisateur

IDTECK

IDTECK SR10RW Manuel utilisateur

IDTECK

IDTECK Star SR10 Manuel utilisateur

IDTECK

IDTECK SR30 Manuel utilisateur

IDTECK

IDTECK PROX10 Manuel utilisateur

IDTECK

IDTECK Star SR10 Manuel utilisateur

IDTECK

IDTECK Star RF TINY Manuel utilisateur

IDTECK

IDTECK Star RFK101 Manuel utilisateur

IDTECK

IDTECK LX006 Manuel utilisateur

IDTECK

IDTECK SR10S Manuel utilisateur

IDTECK

IDTECK PROX10 Manuel utilisateur

IDTECK

IDTECK RF900I-8 Manuel utilisateur

IDTECK

IDTECK Star RFK101 Manuel utilisateur

IDTECK

IDTECK SRK101 Manuel utilisateur

IDTECK

IDTECK Star RF30 Manuel utilisateur

IDTECK

IDTECK FGR006 Manuel utilisateur

IDTECK

IDTECK NEO RF245 Manuel utilisateur

Manuels Lecteur de cartes populaires d'autres marques

Lindy

Lindy 43185 Manuel utilisateur

Lindy

Lindy 43185 Manuel utilisateur

ViziT

ViziT RD-4F Manuel utilisateur

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manuel utilisateur

AVID ID

AVID ID AVID1043 Manuel utilisateur

Conrad

Conrad PCMCIA Manuel utilisateur

Rosslare

Rosslare DR-6255 Manuel utilisateur

Lindy

Lindy 51541 Manuel utilisateur

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manuel utilisateur

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manuel utilisateur

ACS

ACS ACR122L Manuel utilisateur

Secukey

Secukey S2-MF Manuel utilisateur

Elecom

Elecom MR-SMC07 series Manuel utilisateur

Alien

Alien ALR-9800 Manuel utilisateur

ACS

ACS ACR310 Manuel utilisateur

Datamars

Datamars R-IN1300 MID Manuel utilisateur

Alarm Lock

Alarm Lock AL-PRE2 Manuel utilisateur

xpr

xpr B100PROX-AH Guide de l'utilisateur