IDTECK SR10RW Manuel utilisateur

User’s Manual

13.56MHz [MIFARE]

Contactless Smart Card Reader / Writer

Table of Contents

1. Important Safety Instructions ...................................................... 3

2. General................................................................................... 4

3. Features.................................................................................. 4

4. Specification............................................................................ 5

5. Identifying Supplied Parts........................................................... 5

6. Installation .............................................................................. 6

7. Color Coded & Wiring Table ........................................................ 8

8. Output Format.......................................................................... 9

9. Wire Connection to Access Controller ......................................... 11

10. Operation ............................................................................ 12

11. Troubleshooting .................................................................... 14

12. FCC Registration Information................................................... 15

13. Warranty Policy and Limitation of Liability .................................. 16

14. How to Make RMA Request (After Sales Service).......................... 17

1. Important Safety Instructions

The description below is to keep user’s safety and prevent any product damage. Please full

y read these instructions and use the product properly.

Danger: This symbol indicates that incorrect handling of the product may resu

lt in serious injury or death.

Warning: This symbol indicates that incorrect handling of the product may res

ult in injury or property damage.

- Only use the standard voltage (DC +12V / 350mA).

- If the product emits smoke or smells, stop using the product. Unplug the product from DC power source

and contact nearest service center.

- Do not install the product in a place subject to humidity, dust (metallic dust) or splashing water

(raindrops).

- Do not install the product in a place not meeting the operating humidity and temperature specified in the

specification.

- Do not install the product with tools such as driver in hand when power is being supplied.

- Do not drop liquid onto the product such as water and give the product a severe shock.

- Do not place magnetic objects near the product.

- Do not replace the wiring cables installed by experts.

- Do not use the product under direct sunlight or in a heat-producing place such as a place near a heating

apparatuses.

- If you want to relocate the installed product, turn power off and then move and reinstall it.

- Do not use flammable sprays or objects near the product.

- Do not let anyone but the manger touch the product except using it for normal purpose.

- If liquid has been spilled on the product, unplug it first.

- Do not clean the product with water. Clean gently with dry cloth or towel.

- Do not use chemicals such as benzene, thinner or acetone for cleaning.

CAUTIONS ABOUT INSTALLATION

CAUTIONS ABOUT POWER

CAUTIONS ABOUT USAGE

CAUTIONS ABOUT CLEANING

2. General

The IDTECK SR10RW Smart Card Reader / Writer can be compatible with Philips Mifare™ Card.

The unit provides integrated operation of reader and writer and is designed by which can install easily to

door frame or wall.

The IDTECK SR10RW is elegant looking and built in an attractive 10cm (4") read range smart card reader.

It also reads serial numbers from Philips Mifare™ Cards compatible, and can read and write special data

of memory field internal card when operating of the unit is set by PRG2000RW.

The IDTECK SR10RW can support communication between PRG2000RW, PC and third party controller

using methods of RS232 and RS485.

Three LED indicators of red and green, inside Piezo buzzer sound will guarantee you accurate and reliable

system operations.

3. Features

- 13.56MHz [MIFARE] Contactless smart Card Reader / Writer

- Read Range: Up to 4 inch (10cm)

- Read the Card which is issued by PRG2000RW (Smart Card Read / Write Programmer)

- RS232 / RS485 (default), 26 / 34bit Wiegand (selectable) Output Format

- 3 Array LED Indicators (Red and Green) and Buzzer

- External LED Control

- External Buzzer Control

- Easy to install on Mullion Mounting

- Solid Epoxy Potted

- Waterproof / IP65 / IP66

- Reverse Polarity Protection

- Compatible Software: Smart Card Read / Write Software

- Compatible Controller:

(26bit Wiegand) iCON100, iTDC, iMDC, Third Party Controller

(34bit Wiegand) iCON100SR, iTDC-SR, iMDC, Third Party Controller

4. Specification

Model

SR10RW

CPU

8bit Microprocessor

Frequency

13.56MHz [MIFARE]

Read Range

ISK50 / IHC80 / IMC135: Up to 2 inches (5cm),

ISC80: Up to 4 inches (10cm)

Reading Time

30ms

Power / Current

DC12V / Max.150mA

Read Range

ISK50/IMC135 : 2 inches (5cm)

ISC80 : 4 inches (10cm)

Output Format

RS232 / RS485 (Default), 26 / 34bit Wiegand (Selectable)

LED Indicator

3 Array LED Indicators (Red, Green)

Beeper

Piezo Buzzer

Operating Temperature

-35to +65C ( -31F to +149F )

Operating Humidity

10% to 90% relative humidity non-condensing

Color

Dark Pearl Gray

Material

Polycarbonate

Dimension (W x H x T)

1.8" X 4.5" X 0.88" (47mm X 115mm X 22mm)

Weight

120g (0.26lb)

Certification

FCC, CE, KCC, RoHS

5. Identifying Supplied Parts

Please unpack and check the contents of the box.

Reader Module

SR10RW Bezel

User’s Manual

Anchor Bolt

3.5*40 screw

3.5*25 screw

Magnet

(1ea)

(1copy)

(2ea)

(1ea)

6. Installation

6-1. Mullion/Wall Mount:

Drill 6-32 or M3 screws hole at 3.3" (8.38cm) intervals vertically

And drill one 1/2" hole between previously drilled two holes for the reader cable 1.7" apart from the

top hole.

(If the gang box is already installed on the wall then skip this step.)

6-2. Fixing a Tamper Magnet to the wall

Attach a tamper magnet with tools such as double-sided tape on the left of the bottom hole that you

drilled in 6-1. (Refer to the figure below)

6-3. Fixing Reader Module

Put reader cable into the center hole and fix the reader module using two 6-32 or M3 screws.

6-4. Putting on the Cover

Put on cover into the reader module, and then push it until hearing the locking sound.

6-5. Cautions during Installation

6-5-1. When installing SR10RW on metal Frame

Read range will be reduced if located on metal surfaces or in the vicinity of metal objects. The

amount of reduction will be a factor of the amount of metal and the distance the Reader is from

the metal. Metal near the Reader absorbs energy from the Reader excite field and affects the

signal being received from the card by re-directing excite field transmissions into the receiver

circuitry. Moving the Reader away from the metal objects reduces energy loss.

Try to limit the amount of metallic materials installed near the SR10RW.

Use a plastic electrical box if possible.

When installing the Reader on metal door frame, add Isolation Spacers between the Reader and

metal door frame. If you do so, read range reduction can be improved.

The typical read distance specification (2-4 inches at 12VDC) refers to operation without metal in

the vicinity of the Reader.

The read distance will be reduced if metal is installed nearby. The SR10RW generate a magnetic

field on all sides of the Reader. Any metal that conducts electricity, especially metal that contains

iron, steel or copper will interfere with the field and reduce the effective spacer between the

Reader and the metal object.

6.5.2. When installing two readers side by side or back to back

Read range is not affected if the side by side distance between two readers is equal to

or greater than eight inches (20cm). If the distance between the two readers is less than

eight inches (20cm), field interference between the two readers may result in a double-

badge read.

When installing two readers back-to-back on a wall that will separate the two readers by

Two readers can simultaneously read the same badge or tag if the distance

between the two readers is less than 8 inches (20cm), side by side.

Note

eight inches (20cm) or less, a metal plate (for example: Reader isolation plate, metal wall)

must be placed between the readers. To obtain the maximum read range, mount each

proximity reader onto one or more Isolation Spacers.

7. Color Coded & Wiring Table

Signal

Color

Main Power (+12V)

Red

Power Ground (GND)

Black

ABA Track II CP Out

Orange

Wiegand Data 0 Out / ABA Track II Data Out

Green

Wiegand Data 1 Out / ABA Track II Clock Out

White

Buzzer Control In

Blue

LED Control In

Yellow

Tamper Switch Out

Gray

RS232 (TX)

Purple

RS232 (RX)

Brown

RS485 (A)

Pink

RS485 (B)

Cyan

* Cut out the tail connector before installation.

Two readers can simultaneously read the same badge or tag if the distance

between the two readers is less than 8 inches (20cm), back-to-back.

Note

8. Output Format

8-1. 26/34bit Wiegand output format

1. Data format

26bit Wiegand output format

34bit Wiegand output format

Bit 1

Even parity of bit 2 ~ bit 13

Bit 1

Even parity of bit 2 ~ bit 17

Bit 2∼9

Facility code (000 ~ 255)

Bit 2∼25

4byte ID number

(0000000001 ~ 4,294,967,295)

Bit 10∼25

ID number (00000 ~ 65,535)

Bit 26

Odd parity of bit 14 ~ bit 25

Bit 34

Odd parity of bit 18 ~ bit 33

2. Timing diagram

8-2. ABA Track II Magstripe output format

1. Data format (for Card numbers)

3.5V

0.5V

100uS

1mS

Data 0

100uS

Data 1

3.5V

0.5V

Start Character

(11010 Hex ‘B’)

ID number

(1248P (0000000001~ 4294967295))

low bit first, odd parity last

LRC

Zero bit

Zero bit (10bit)

2. Data format (for PIN)

3. Timing diagram

8-3. RS-232 output format

1. Data format (Baud rate: 9600bps)

+15V

-15V

+3V

-3V

Space (=0)

Mark (=1)

8 Data Bits 2 Stop Bits

Indeterminate

Region

Data packet corresponding to ASCII character 'A'

Start Bit

0 1 0 0 0 0 0 1 0

LSB MSB

Start Character

(11010 Hex ‘B’)

PIN (1char to 8char)

low bit first, odd parity last

LRC

Zero bit

Zero bit (10bit)

CLK

(RD1)

Data

(RD0)

1240us

940us

6000us

1544us

Table des matières

Autres manuels IDTECK Lecteur de cartes

IDTECK

IDTECK Star SR10 Manuel utilisateur

IDTECK

IDTECK Star RF30 Manuel utilisateur

IDTECK

IDTECK Star RF TINY Manuel utilisateur

IDTECK

IDTECK SR30 Manuel utilisateur

IDTECK

IDTECK Star RFK101 Manuel utilisateur

IDTECK

IDTECK ipass IP10 Manuel utilisateur

IDTECK

IDTECK SRK101 Manuel utilisateur

IDTECK

IDTECK Star RFK101 Manuel utilisateur

IDTECK

IDTECK RF900I-8 Manuel utilisateur

IDTECK

IDTECK FGR006 Manuel utilisateur

IDTECK

IDTECK Star FINGER006 Manuel utilisateur

IDTECK

IDTECK Star RFK505 Manuel utilisateur

IDTECK

IDTECK SR10S Manuel utilisateur

IDTECK

IDTECK Star RF10 Manuel utilisateur

IDTECK

IDTECK SR10/30V Manuel utilisateur

IDTECK

IDTECK Star RFK505 Manuel utilisateur

IDTECK

IDTECK SR30 Manuel utilisateur

IDTECK

IDTECK Star SR10 Manuel utilisateur

IDTECK

IDTECK PROX10 Manuel utilisateur

IDTECK

IDTECK NEO RF245 Manuel utilisateur

IDTECK

IDTECK NEO RF245 Manuel utilisateur

IDTECK

IDTECK LX006 Manuel utilisateur

IDTECK

IDTECK Star RFK101 Manuel utilisateur

IDTECK

IDTECK STAR RF70 Manuel utilisateur

Manuels Lecteur de cartes populaires d'autres marques

Lindy

Lindy 43185 Manuel utilisateur

Lindy

Lindy 43185 Manuel utilisateur

ViziT

ViziT RD-4F Manuel utilisateur

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manuel utilisateur

AVID ID

AVID ID AVID1043 Manuel utilisateur

Conrad

Conrad PCMCIA Manuel utilisateur

Rosslare

Rosslare DR-6255 Manuel utilisateur

Lindy

Lindy 51541 Manuel utilisateur

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manuel utilisateur

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manuel utilisateur

ACS

ACS ACR122L Manuel utilisateur

Secukey

Secukey S2-MF Manuel utilisateur

Elecom

Elecom MR-SMC07 series Manuel utilisateur

Alien

Alien ALR-9800 Manuel utilisateur

ACS

ACS ACR310 Manuel utilisateur

Datamars

Datamars R-IN1300 MID Manuel utilisateur

Alarm Lock

Alarm Lock AL-PRE2 Manuel utilisateur

xpr

xpr B100PROX-AH Guide de l'utilisateur