IDS 860-06-0005 Manuel utilisateur

Channe

Remot

Receive

Channe

Remot

Receive

Channe

Remot

Receiver

•The Normally Open (NO), Normally Closed (NC)

Channel

Receiver (Digital)

P/N 860-06-0005

Specifications

Power Supply 12V - 16V

Max. Power Consumption

175mA

Weight 145g

Dimensions (H x W x L) 33 x 66 x 104

Features

•Two channel receiver

•High noise immunity

•238 Users + 64 supervised RF devices may

learned

•Signal Jamming Detection and Ambient

Noise

Level indication

•Advanced RF anti-collision software

•Individual relay pulse periods selectable up to 10

minutes

•Dedicated panic remotes may be learned

•Selectable retrigger protection on any relay

•Panel arming / disarming / stay arming and

panic

through keypad bus

•Expansion of panel zones with RF devices

such

as RF passives.

3. Introduction

The IDS Digital Wireless Receiver is an extremely

versatile

receiver unit that may be used either as a

standalone

product or in conjunction with any DIGITAL IDS alarm

panel

such as the IDS 816, 1224 or 1632. When used with

DIGITAL IDS alarm panel, the receiver connects onto

the

same communication and power bus as the keypad

and

no other connections are needed to make use of any

the advanced receiver functions.

4. Installation and Wiring

•The IDS Digital Wireless receiver may be used

either a standalone mode or connected to an IDS

and

Common

(COM)

outputs

both

relays

are

available to be connected to external devices

such

as gate operators or other alarm panels.

•Relay 4ís NO contact is only available with

jumper

6 in position 2. When Jumper 6 is in position 1

Relay 4ís NO contact is connected to ground

via

the tamper switch on the receiver.

•For ease of programming Jumper 5 may be used

to remove power to the unit after installation.

5. Switches, Jumpers, and Relays

•The IDS Digital Wireless Receiver has 8 DIP

switches, 1 Tamper switch and 2 Jumpers

•The 8 DIP switches are used to program

the

receiver and adjust its available features.

When

connected to an IDS DIGITAL alarm panel

the

programming of users and RF devices such

RF Passives are done through the panel

keypad.

The programming of any of the other features does

however still need to be done using the

DIP

switches.

•Jumper 5 is the power jumper that may be used

remove power from the unit when required to

so during programming.

•Jumper 6 selects between Relay 4ís NO

contact

or the Tamper Switch Contact. The tamper

switch

is internally connected to ground.

•Any of the relay outputs may be used to switch

maximum of 3A at a maximum of 24V DC.

The

relays are not intended for switching high voltage

Colour

White

Channels 2

Users 238

Passives (Supervised) 64

•

DIGITAL

alarm

panel.

When used in standalone mode, the rece

iver

needs a supply of between 12V and 16V DC.

The

Data lines D+ and D- do not need to be

connected.

When connected to a DIGITAL IDS alarm

panel,

the D+ and D- data lines must be connected

the panelís D+ and D- data lines. (Connection

relays to arm and disarm the panel via zones

NOT needed. Arming and disarming of the

panel

is done through the data bus.)

signals

directly

such

lights

motors.

IDS

700

284

200

1.40

IDS

Channe

Remot

Receive

Channe

Remot

Receive

Channe

Remot

Receiver

Programmin

Uni

Stand

Alone

Mode. (Power Up Settings)

N.B. to change any settings on the receiver unit, the

receiver needs to be powered down, the

settings

changed and then powered up again.

Restoring the Factory Default Settings:

1. Remove power from the unit by removing jumper

J5 and switch all DIP switches OFF.

2. Switch DIP switches 1, 5, 6, 7 and 8 ON.

3. Restore Power to the Unit by replacing J5.

4. Switch DIP Switch 8 OFF.

5. Wait for the LEDís to start flashing alternately.

6. Switch ALL Dip switches OFF.

7. When the LEDís stop flashing the unit is in

the

normal operating mode.

The factory default settings with all Dip switches

OFF and all jumpers ON are as follow:

Three Minute Retrigger Protect Off

Remote Learn Off

Panic Remote Learn Off

RF Device Learn Off

Ambient Noise Level Test Off

Device Failure Relay Disabled

Panic Relay Enabled

3 Sec Remote Panic

Enabled

Relays

Pulse

Relay 4 Output

Selected

Power Jumper On

Relay Pulse Period 3 Sec

Relays Safe / Secure

Secure

Panic Relay Relay 4

RF Device Output Relay None

Remote Button Outputs

Button 1 Relay 1

Sec

Hold

for

Panic

Button

Relay 3 Min Retrigger Protect

None

Signal Jamming Detect Period

30s

Device Not Reporting 1hr max

Deleting ALL the User Remotes:

1. Remove power from the unit by removing

jumper

J5 and switch all DIP switches OFF.

2. Switch DIP switches 2, 5, 6, 7 and 8 ON.

3. Restore Power to the Unit by replacing J5.

4. Switch DIP Switch 8 OFF.

5. Wait for the LEDís to start alternating.

6. Switch ALL DIP switches OFF.

7. When the LEDís stop flashing the unit is in

the

normal operating mode.

Deleting ALL Supervised RF Devices

(e.g. RF Passive IR’s):

1. Remove power from the unit by removing

jumper

J5 and switch all DIP switches OFF.

2. Switch DIP switches 3, 5, 6, 7 and 8 ON.

3. Restore Power to the Unit by replacing J5.

4. Switch DIP Switch 8 OFF.

5. Wait for the LEDís to start flashing alternately.

6. Switch ALL DIP switches OFF.

7. When the LEDís stop flashing the unit is in

the

normal operating mode.

Adjusting the Relay Pulse Periods:

1. Remove power from the unit by removing

jumper

J5 and switch all DIP switches OFF.

2. Switch DIP switches 7 and 8 ON.

3. Restore Power to the Unit by replacing J5.

4. To adjust relay 1ís pulse period, switch DIP

switch

1 ON.*

5. Wait for as long as the pulse needs to be (Up to

10 minutes).

6. Switch DIP switch 1 OFF (For relay 1ís

pulse

period).

7. Switch DIP switch 8 OFF.

8. Wait for the LEDís to start flashing alternately.

Switch

ALL

DIP

switches

OFF.

10. When the LEDís stop flashing the unit is in

the

normal operating mode.

Changing Between Relay Safe and Secure

Modes:

1. Remove power from the unit by removing

jumper

J5 and switch all DIP switches OFF.

2. Switch DIP switches 6 and 8 ON.

3. Restore Power to the Unit by replacing J5.

4. To make Relay 1 and 4 Fail Safe, switch

DIP

switches 1 and 4 ON.* (Any relay not selected

will

be Fail Secure.)

5. Switch DIP switch 8 OFF.

6. Wait for the LEDís to start flashing alternately.

7. Switch ALL DIP switches OFF.

8. When the LEDís stop flashing the unit is in

the

normal operating mode.

Selecting the Panic Relay Output:

1. Remove power from the unit by removing

jumper

J5 and switch all DIP switches OFF.

2. Switch DIP switches 6, 7 and 8 ON.

3. Restore Power to the Unit by replacing J5.

4. Select the relay to be the Panic Relay.* (If no

relay

is selected, the panic relay will be disabled.)

5. Switch DIP switch 8 OFF.

6. Wait for the LEDís to start flashing alternately.

7. Switch ALL DIP switches OFF.

8. When the LEDís stop flashing the unit is in

the

normal operating mode.

* * Where indicated DIP switch 1 represents Relay 1,

DIP switch 4 represents Relay 4.

IDS

700

284

200

1.40

IDS

Channe

Remot

Receive

Channe

Remot

Receive

Channe

Remot

Receiver

Selecting

the

Relay

Activate

When

Remote

Button is Pressed:

1. Remove power from the unit by removing jumper

J5 and switch all DIP switches OFF.

2. Switch DIP switches 5 and 8 ON.

3. Restore Power to the Unit by replacing J5.

4. Select the relay to be the new Output Relay.*

(If

no relay is selected, no relay will be activated

when

the remote button is pressed.)

5. Press the button on a learned remote that

must

activate the selected relay output.

6. Switch DIP switch 8 OFF.

7. Wait for the LEDís to start flashing alternately.

8. Switch ALL DIP switches OFF.

9. When the LEDís stop flashing the unit is in

the

normal operating mode.

Protecting Relays from retriggering within 3

minutes after a previous trigger:

1. Remove power from the unit by removing jumper

J5 and switch all DIP switches OFF.

2. Switch DIP switches 5, 7 and 8 ON.

3. Restore Power to the Unit by replacing J5.

4. Select the relay(s) to be retrigger protected.*

5. Switch DIP switch 8 OFF.

6. Wait for the LEDís to start flashing alternately.

7. Switch ALL DIP switches OFF.

8. When the LEDís stop flashing the unit is in

the

normal operating mode.

Assigning a Relay to be Activated when a RF

Device is Triggered:

1. Remove power from the unit by removing jumper

J5 and switch all DIP switches OFF.

2. Switch DIP switches 5, 6 and 8 ON.

3. Restore Power to the Unit by replacing J5

4. Select the relay to be activated.* (If no relay

selected, no relay will be activated when

the

remote button is pressed.)

5. Trigger the device that must activate the selected

Relay Output.

Switch

Dip

switch

OFF.

7. Wait for the LEDís to start flashing alternately.

8. Switch ALL Dip switches OFF.

9. When the LEDís stop flashing the unit is in

the

normal operating mode.

Assigning a Dedicated Panic Button to a

Remote:

N.B. This Function will affect ALL remotes.

1. Remove power from the unit by removing

jumper

J5 and switch all Dip switches OFF.

2. Switch Dip switches 4 and 8 ON.

3. Restore Power to the Unit by replacing J5.

4. Press the button on a known remote that

will

become an instant panic button.

5. Switch Dip switch 8 OFF.

6. Wait for the LEDís to start flashing alternately.

7. Switch ALL Dip switches OFF.

8. When the LEDís stop flashing the unit is in

the

normal operating mode.

Assigning an Arm / Disarm Button on a Remote:

N.B. This Function will affect ALL remotes.

1. Remove power from the unit by removing

jumper

J5 and switch all Dip switches OFF.

2. Switch Dip switches 3 and 8 ON.

3. Restore Power to the Unit by replacing J5.

4. Press the button on a known remote that

will

become the Arm / Disarm button.

5. Switch Dip switch 8 OFF.

6. Wait for the LEDís to start flashing alternately.

7. Switch ALL Dip switches OFF.

8. When the LEDís stop flashing the unit is in

the

normal operating mode.

Assigning a Stay Arm Button on a Remote:

N.B. This Function will affect ALL remotes.

1. Remove power from the unit by removing

jumper

J5 and switch all Dip switches OFF.

2. Switch Dip switches 2 and 8 ON.

3. Restore Power to the Unit by replacing J5.

Pres

butto

know

remot

tha

will

become the Stay Arm button.

5. Switch Dip switch 8 OFF.

6. Wait for the LEDís to start flashing alternately.

7. Switch ALL Dip switches OFF.

8. When the LEDís stop flashing the unit is in

the

normal operating mode.

Assigning the Device Failure Output Relay:

1. Remove power from the unit by removing

jumper

J5 and switch all Dip switches OFF.

2. Switch Dip switches 4, 7 and 8 ON.

3. Restore Power to the Unit by replacing J5.

4. Switch Dip switch 4 OFF.

5. Select the relay to be the Device Failure

Relay.*

(If no relay is selected, the device failure relay

will

be disabled.)

6. Switch Dip switch 8 OFF.

7. Wait for the LEDís to start flashing alternately.

8. Switch ALL Dip switches OFF.

9. When the LEDís stop flashing the unit is in

the

normal operating mode.

Learning a New RF Device such as a RF Passive

IR:

1. Remove power from the unit by removing

jumper

J5 and switch all Dip switches OFF.

2. Switch Dip switches 3, 7 and 8 ON.

3. Restore Power to the Unit by replacing J5.

4. Press the TAMPER switch on the Device to be

Learned.

5. Switch Dip switch 8 OFF.

6. Remove power from the unit and adjust Dip

switch

setting as needed.

7. Restore power to the unit. When the LEDís

stop

flashing the unit will be in normal operating mode.

* * Where indicated DIP switch 1 represents Relay 1,

DIP switch 4 represents Relay 4.

IDS

700

284

200

1.40

IDS

Channe

Rem

Receive

Channe

Remot

Receive

Channe

Remot

Receiver

Programmin

Uni

Stand

Alone

Mode. (Normal Settings)

These settings may be adjusted during

normal

operation and it is not necessary to power the

unit

down for the settings to take effect.

Remote Arm or Disarm 3 Minute Retrigger Protecting:

1. Switch Dip switch 2 ON to enable

retrigger

protecting.

Learning New Remotes:

1. Switch DIP switch 3 ON to enable learning of

new

remotes.

2. Press any button on the remotes to be learned.

3. Switch DIP switch 3 OFF to exit the learn mode.

To indicate the Ambient Noise Level:

N.B. This function must be disabled during

normal

operation

This function allows the testing of ambient noise

Press

any

button

the

remotes

learned.

3. Switch DIP switch 6 OFF to exit the learn mode.

Disable the 3 second Hold for Panic Feature:

1. To disable the 3 second hold for panic feature

ALL remotes switch DIP switch 7 ON.

Changing the Relays from Pulsing to Toggling:

1. Remove power from the unit by removing

jumper

J5 and switch all DIP switches OFF.

2. Switch DIP switches 5, 6, 7 & 8 on.

3. Restore the power to the Unit by replacing J5.

4. To select toggling relays, use DIP switches 1 & 4

for Relays 1 & 4.

5. Switch DIP switch 8 off.

6. Wait for the LEDís to start alternating.

7. Switch all DIP switches off and set DIP switches

Connector

Switc

Jumpe

Positions

10.Program Summary and LED Indications:

environmen

surroundin

receive

during

the

desired

setting.

Fun

installation.

1. Switch DIP switch 4 ON to enable noise

level

testing.

2. ONLY install the receiver in an environment

with

normal or better noise Levels.

During noise testing the LEDís indicate the

following:

Programmin

Uni

Connecte

DIGITAL IDS alarm panel.

When connected to a DIGITAL IDS alarm

panel,

programming of the unit is as for the Stand-

Alone

mode with the following exceptions.

SAB

LEARN

PANIC

ERROR

RELAY

TEST

NOISE

LEARN

RETRIG

PROTECT

PULSE

PERIOD

LED

LEVE

Learning

and

Deleting

Individual

User

Remotes:

1. To learn a new user remote, leave DIP switch 3

PANIC

RELAY

FOR

OFF VERY LOW

nee

switche

normal

operatio

whe

connecte

DIGITAL

RELAY

FOR

DEVICE

alarm

panel).

the

user

manual

the

DIGITAL

IDS

alarm

STAY

BUTTON

panel

for

learning

new

users.

Learning New Supervised RF Devices and

deleting

RECEIVER

Devices by Zone allocation:

1. Follow the user manual of the DIGITAL IDS alarm

TOGGLE

DELETE

DEVICES

Enabling

the

Device

Failure

Relay

Output:

1. Switch DIP switch 5 ON

panel

for

learning

new

devices

and

deleting

RF devices by zone.

FACTORY

RESETS

Learn

New

Panic

Remotes:

1. Switch DIP Switch 6 ON

IDS

IDS 700-284-5 AUG 2005 VER

1.40

IDS

BLINK

FAST

SLO

ALT

GREEN

LED

BUSY

SIGNAL

INVALID

SIGNAL

LOW

BATT

IDS

Autres manuels IDS Récepteur

IDS

IDS 400 Manuel utilisateur

IDS

IDS X-Series Rx2 Guide de l'utilisateur

IDS

IDS 860-06-0003 Manuel utilisateur

IDS

IDS X64 Guide de l'utilisateur

IDS

IDS 860-06-0004 Manuel utilisateur

IDS

IDS Xwave Guide d'installation

IDS

IDS MKII Guide de l'utilisateur

Manuels Récepteur populaires d'autres marques

Garmin

Garmin GA 23 Manuel utilisateur

Aiphone

Aiphone PS-12F Manuel utilisateur

IMES

IMES TCS-01CA-PMI Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuel

AMIMON

AMIMON AMN12310 WHDI Manuel utilisateur

Dual

Dual DMCPA79BT Mode d'emploi

Sound Associates

Sound Associates SA652P Manuel utilisateur

Sherwood

Sherwood NewCastle R-772 Manuel utilisateur

Audio

Audio A10-RX Series Manuel utilisateur

AllSee

AllSee PushShare PSRV1.1 Manuel utilisateur

DEMAG

DEMAG DRC-DR D2 Manuel utilisateur

Teleco

Teleco TVRCL868A02 Manuel utilisateur

Bosch

Bosch RF3222E Manuel utilisateur

Kramer

Kramer 631R Manuel utilisateur

Xpress

Xpress xmc10 Manuel utilisateur

JVC

JVC KD-MR1BTS Manuel utilisateur

Omega Engineering

Omega Engineering UWTC-REC3 Manuel utilisateur

e-survey

e-survey E300 Pro Manuel utilisateur