Ideal-Standard TEMPO IDEALFORM PLUS+ Manuel utilisateur
TEMPO
IDEALFORM PLUS+
SHOWER BATH
Installation Instructions
Please pass on to user
5041 09/13
EE75408967
5041 Tempo Baths:Layout 1 10/09/2013 10:24 Page 1
695
(±5)
845
1695
850
AB
510 560
348
250
695
725
795
1695
398
318
Centres of leg adjusters
Tempo Arc
Tempo Cube
A
400
450
B
450
520
Figure 1
TECHNICAL INFORMATION
BEFORE YOU START
●Before commencing installation, carefully remove packaging/protective film and check for
damage. If damaged, report immediately to supplier.
●Check the packs and make sure that you have all parts listed. If not, contact the supplier.
●Ensure the water feeds and waste connection points are positioned appropriately for the
installation.
●Care should always be taken when drilling into walls and floors to avoid any sunken wires
or pipes.
●The bath should be fully protected during the installation process.
●Please note: Although these instructions are comprehensive, it is always recommended
that a technically competent installer should undertake installation.
Appropriate safety equipment/workwear should be used
All dimensions shown in millimeters.
Dimensions shown may vary within permitted tolerances.
5041 Tempo Baths:Layout 1 10/09/2013 10:24 Page 2
B
A
Ref
Leg Support Beam
Bath
Description
2
1
Qty
CLeg 2
DNut 4
EFoot 140mm Long 2
FFoot 120mm Long 2
GPlastic Leg Adjuster 2
or
BATH COMPONENTS
5041 Tempo Baths:Layout 1 10/09/2013 10:24 Page 3
BATH COMPONENTS - FIXING PACK
H1
H2
H4
H7
L
No.8 X 16 Pan Head 14
No.8 X 16 Pan Head (Pre attached to Ref G) 2
H3 Wall Plugs Small 2
Wall Plug Screw Small 2
H5 Wall Plug Large 4
H6 Wall Plug Screw Large 4
Side Wall Bracket Screw 2
J
Corner Wall Bracket 1
I
Wall Support Bracket 2
KSide Wall Bracket 2
1
Curved Bath Support Leg Pack
Ref Description Qty
5041 Tempo Baths:Layout 1 10/09/2013 10:24 Page 4
R
Q
P
O
N
S
T
M
Screw and Cover Caps
No.8 x 19 Pan Head Self Tapping Screw
Metal Panel Clip
Plastic Panel Clip
End Panel
Front Panel
5
8
4
5
1
2
2
1or
Ref Description Qty
FRONT PANEL (Sold & supplied separately)
END PANEL (Sold & supplied separately)
Panel Clip
No.6 x 12 Pan Head Self Tapping Screw
5041 Tempo Baths:Layout 1 10/09/2013 10:24 Page 5
Ref. O
Ref. P
Ref. A
Encapsulated
baseboard
Ref. L
Ref. H1
Ref. B
Ref. F
Ref. C
Ref. D
Ref. F
Ref. G
Ref. H2
Ref. O
Ref. A
Ref. O
Ref. P
Ref. L
Ref. F
Ref. D
Ref. F
Ref. C
Ref. E
Encapsulated
baseboard
Ref. B
Ref. E
Ref. H2
Ref. H1
Ref. G
Ref. P
Ref. O 3
Ref. E
Ref. E
Figure 2
BATH ASSEMBLY
5041 Tempo Baths:Layout 1 10/09/2013 10:24 Page 6
Cranked leg
(Left hand shown)
Ref. L
Figure 3
Cranked leg
(Left hand shown)
Figure 4
5041 Tempo Baths:Layout 1 10/09/2013 10:24 Page 7
Space 510
Ref. H3 Ref. I
Ref. J
Ref. J
Ref. H4
Figure 5
pre-drilled hole
Ref. H5
Ref. H5
Ref. H6
Ref. J
Ref. K
Ref. K
Ref. H6
Ref. H1
Ref. H7
Ref. H7
bath rim
Figure 6
5041 Tempo Baths:Layout 1 10/09/2013 10:24 Page 8
1. Lay bath face down onto a protective surface so as not to damage the bath. Fix leg
adjusters, (Ref. G) onto bath into predrilled holes using screws (Ref H1). Assemble
legs as shown in Fig 2.
2. Push leg sets in to leg adjusters and position leg beams onto baseboard. Mark the
fixing hole positions on the baseboard. Pilot drill the 8 holes in the baseboard, using a
3mm drill to a depth of 6mm maximum. Fix the leg beams to the baseboard using
screws (Ref H1). DO NOT OVER TIGHTEN
3. Locate the 2 pan head self tapping screws (Ref. H2) into leg adjusters and tighten.
Adjust feet to give floor to top of rim height of 560mm
4. Position metal panel clips on to panel clip blocks, Fig. 2a. Pilot drill holes with a 3mm
drill. Use screws (Ref. P) for securing clips.
5. Fit side wall brackets to bath (Ref. K), using pre-drilled holes as a guide. Secure with
screws (Ref. H1). Assemble wall support bracket (Ref. J) onto bath.
6. Fit end panel spring clips (Ref. S) onto bath with screws (Ref T).
7. Fit the single support leg black end cap in a suitable area on the framework,
Figs. 2 & 3.
8. Flip bath onto feet. NOTE: If the bath is to be installed at a lower height than normal,
then provision for the waste trap to be recessed into the floor may be necessary.
Also the bath panel(s) will need to be cut down in height. If lowering panel heights,
remove the material from the bottom of the panel(s) and use wooden blocks (not sup-
plied) to secure to the floor. Reducing the panel height requires great care and Ideal-
Standard cannot accept responsibility for any damage caused.
9. Fit brassware and waste fittings. If the bath is to be installed with a monoblock mixer
a special hole (or holes) is required to accommodate the mixer and will have to be cut
by the installer in an appropriate position on the rim of a no tap hole bath to suit the
bathroom layout. Full details or a template for cutting the hole (or holes) is supplied
with monoblock fittings. A template for cutting two tap holes is supplied with the bath.
Cut tap holes, and fit supply fittings, waste, overflow and trap.
10. Fasten corner wall bracket (Ref. I) onto wall at the correct height (510mm nominal).
11. Place bath into installation position. Ensure bath is levelled and set at the correct
height (510mm to trimmed edge).
12. Fix bath to wall.
INSTALLATION
5041 Tempo Baths:Layout 1 10/09/2013 10:24 Page 9
13. Fix bath to floor, ensuring that all nuts are tight and that the bath is level. Re-adjust if
necessary. Trail fit the panel(s) to verify height is correct.
Note: Untrimmed panel fitment requires the height of 560mm (510 to trimmed edge of
bath). Remember to allow for floor covering thicknesses.
14. Connect services, test for satisfactory operation of fittings and ensure there are no
leaks.
15. Fit the support leg (Ref. L) to the black cap previously fastened to the framework.
Ensure that the leg is adjusted correctly to support the rim but not force the rim
upwards.
16. Tile down to the height of the bath rim leaving a 3-4mm gap for waterproof sealant.
An extruded sealing strip can be used for the bath to wall joint as an alternative to
waterproof sealant. Protect bath during tiling.
Fixing the bath panel
17. Pre fit front panel ensuring that the ends of the
panel are vertical. Mark a line along the front of
the panel on the floor. Remove panel and fix the
plastic panel clips onto the floor/wall(s) (Figure 7).
The front of the block at the floor should be 3mm
back from the marked line.
Note: The front panel may touch the support
leg foot, (Ref. L), depending on its position.
Remedy this by removing a small amount of
material from the panel return.
18. Fit the end panel by using a wooden batten
along the floor for support and engaging the
top of the panel in front of the spring clips.
19. Fit front bath panel in position and press the
edges into the panel clips until fully engaged.
Note: Fit end panel before front panel. If the front
panel does not easily insert under the panel clips,
then release the screws by a quarter of a turn
and retry.
Note: if the front panel has had the returns trimmed
off, then the plastic panel clips will not grip the
panel base. In this instance, use wooden blocks
(not supplied) to secure
the panel to the floor/wall. Screws with cover caps are supplied for this method of fixing.
Wooden batten
(not supplied)
End panel
Floor
Screw and
cover cap
(not supplied)
Figure 7
Figure 8
5041 Tempo Baths:Layout 1 10/09/2013 10:24 Page 10
Table des matières
Autres manuels Ideal-Standard Baignoire
Manuels Baignoire populaires d'autres marques
Lyons
Lyons Elite ETLxx663219 Series Manuel utilisateur
Woodbridge
Woodbridge BJ500 Instructions de montage
Whirlpool
Whirlpool Ariel ARL-702 Manuel utilisateur
TEIKO
TEIKO EXCELLENT DUO Manuel utilisateur
American Standard
American Standard Colony 5-1/2' x 32" Manuel utilisateur
American Standard
American Standard 3052OD.X0X Guide de démarrage rapide
