ICW MD Manuel utilisateur

If you have any questions, please call 1-800-558-4435

MD ARM INSTALLATION INSTRUCTIONS

MD ARM INSTALLATION INSTRUCTIONS - rev 04/22/14 pjm

Page 1 of 3

ATTACH MD

WALL MOUNT

Locate a stud in a

wall you intend to

mount your arm on.

Mark the top hole,

drill 11/64 pilot hole

and insert an ICW

provided #14 screw

and tighten slightly.

Using a level, mark

the 3 lower holes and

drill pilot holes, insert

the last three #14

screws and with the

mount level, tighten

all screws securely.

Lift the wall

mount up to

the bottom

of the TMD

track, or lower

over the top

of the track if

easier. Slide

the clamp

plates into the

groove in the

TMD track.

Track

clamp

plates

Once the

wall plate is

at the height

that you

want it, use

the 5/32 hex

key to lock it

into place by

turning the

3 clamping

screws in

to place

clockwise.

Clamp

screws

ATTACH WALL PLATE TO TRACK

IF MOUNTING DIRECTLY TO WALL

IF MOUNTING TO WALL TRACK

REMOVE COVERS FROM MD ARM Using a Phillips head

screwdriver, remove the four

screws from the upper cover,

exposing the cable channel.

WARNING - PINCH POINT:

Keep ﬁ ngers away from

the inner arm area where

the gas spring is located.

The lower cover can also

be removed by lowering the

arm into the down position,

removing the screws and

sliding the cover forward off

of the arm.

MD ARM INSTALLATION INSTRUCTIONS - rev 04/22/14 pjm

Page 2 of 3

MD ARM INSTALLATION INSTRUCTIONS

ADJUST BALL VESA

TENSION & HEIGHT

Use the slider knob to

loosen the slider to adjust

the height of the monitor

on the Paralink.

Adjust the pivot tension

of the ball by gently and

evenly tightening or

loosening the four screws

on the back of the ball

VESA.

Slider Knob

Pivot tension

adjustment

screws

ATTACH VESA TO MONITOR

Attach VESA to

monitor using four

4mm screws in the

hardware bag.

ADJUST

PARALINK TILT

Adjust monitor to desired

position with ball VESA.

Tilt your monitor 50°

in any direction. Adjust

your monitor between

portrait and landscape

by rotating ball VESA.

Adjust monitor depth

by moving the paralink

forward or back then

tighting the depth

adjustment knob.

Depth

Adjustment

Knob

ATTACH THE THBV HANDLE

The THBV is attached

to the Paralink and

Quicklink by two

screws on the back of

the VESA plate.

Screw

to attach

handle.

Screw

to attach

handle.

ATTACH

PARALINK

TO MD ARM

Attach the Paralink to

MD arm using 3/8 bolt

assembly and 1” bearing

assembly provided. Insert

bolt assembly up through

ear at end of arm. Place 1”

bearing assembly over bolt

on top of ear. Place Paralink

over bolt and bearing and

turn bolt until Paralink is

secure and smoothly turns

against the bearing. Beauty cap

3/8 bolt

1” bearing

MD ARM INSTALLATION INSTRUCTIONS - rev 04/22/14 pjm

Page 3 of 3

MD ARM INSTALLATION INSTRUCTIONS

ATTACH FLIP UP

1.Remove screws from

drop extension using

5/32” hex key.

2.Align holes in keyboard

tray with screw holes in

drop extension.

3.Attach keyboard tray

using the provided

screws.

IF USING PARALINK KEYBOARD TRAY

IF USING ULTRA

KEYBOARD TRAY

ADJUST MD ARM RESISTANCE

Using the 3/16”

t - h a n d l e h e x

wrench provided,

turn the screw in the

MD arm clockwise

to lighten the arm’s

load resistance, or

counter-clockwise

to increase the load

resistance.

ATTACH COVERS TO MD ARM After lowering the arm to the

down position, slide on the

lower cover. Using a Phillips

head screwdriver (NOT

POWER TOOLS), reattach the

four screws attaching the lower

cover.

Attach the top cover by

reattaching the four top cover

screws using a Phillips head

screwdriver (NOT POWER

TOOLS).

WARNING - PINCH POINT:

Keep ﬁ ngers away from the

inner arm area where the gas

spring is located.

ATTACH QUICK DISCONNECT

1.Remove beauty cap on quick

disconnect block.

2.Remove screw using 3/16”

hex key.

3.Slide keyboard tray into quick

disconnect block.

4.Replace screw and tighten.

5.Replace beauty cap.

Beauty cap

Screw

ATTACH PARALINK KEYBOARD TO MONITOR

Attach the Paralink

Keyboard Mount to the

Monitor Mount by using

the 3/8-16 screw and lock

washer provided.

Autres manuels ICW Support et étagère

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur