Icom IC-7300 Manuel utilisateur

Autres manuels pour IC-7300

12

Table des matières

Autres manuels Icom Émetteur-récepteur

Icom

Icom IC-V3500 Guide de configuration

Icom

Icom IC-A110 Manuel utilisateur

Icom

Icom IC-Delta1A Manuel utilisateur

Icom

Icom IC-F110 Manuel utilisateur

Icom

Icom IC-M304 Manuel utilisateur

Icom

Icom IC-M604A Manuel utilisateur

Icom

Icom IC-M71 Manuel utilisateur

Icom

Icom IC-G86 Guide de configuration

Icom

Icom IC-F51V Manuel utilisateur

Icom

Icom ic-f1000d series Manuel utilisateur

Icom

Icom iF3011 Manuel utilisateur

Icom

Icom IC-M802 Manuel utilisateur

Icom

Icom iC-7850 Manuel utilisateur

Icom

Icom IC-751 Manuel utilisateur

Icom

Icom IC-7410 Manuel utilisateur

Icom

Icom IC-7300 Guide d'installation

Icom

Icom ID-51A Manuel utilisateur

Icom

Icom IC-M10E Manuel utilisateur

Icom

Icom IC-F510 Manuel utilisateur

Icom

Icom IC-T10 Guide d'installation

Icom

Icom IC-25A Manuel utilisateur

Icom

Icom IC-737A Manuel utilisateur

Icom

Icom iF3102D Manuel utilisateur

Icom

Icom IC-M33 Manuel utilisateur

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur

ICOM –IC7300 –QUICK START OPERATING GUIDE

By K7HCP

The ICOM IC-7300 is an HF + 6 meter, multi-mode, self-contained Software

Defined Radio (SDR) transceiver with knobs, buttons and a touch screen. It also

has a real-time spectrum display with pan adapter and water fall displays.

It stands alone and does not require attachment to a computer to function like

most SDR radios in the past.

However to operate this radio using digital mode computer software such as

WSJT-X (FT8) or DigiPan (PSK31) all that is required is a single USB cable with NO

other digital interface hardware required such as sound card interface device.

GETTING STARTED:

Press the POWER button

Turn the AF gain to 9 o-clock

Turn the RF gain/Sql to 12 o-clock

Turn the MAIN DIAL (the big knob) to change frequency

To change Bands:

Touch the MHz frequency display area of the touch screen (touch the “7”of 7.073)

To change Mode:

Touch the Mode area displayed on the touch screen (touch the “LSB”)

To change Filters:

Touch the Filter area displayed on the touch screen (touch the “Fil2”)

To display the Scope:

Press the M.Scope button located below the display to display the small spectrum scope.

Press and Hold the M.Scope button located below the display to display the large spectrum

scope.

NOTE: The “Multi -”Function Control Knob”located just to the right of the display and near the top of

the radio. This knob is used the make selections from various lists of options from time to time.

Press the Multi button, then touch the desired selection. Then turn the knob to choose your setting.

Finally press the button to exit.

To change Frequency:

There are several ways to change the current frequency of the transceiver:

1. Turn the Main Dial (the big knob)

2. While displaying the Spectrum Scope, touch the area of a desired signal spike.

The scope display area touched will be magnified.

Touch the magnified area again and the transceiver will change frequency corresponding to

the frequency of the desired signal.

3. Using pre stored Memories:

Press the MENU button

Then press the MEMORIES button

Then rotate the MULTI knob to select the desired memory channel

Then touch the desired memory channel to choose your selection.

To display the Meters:

Press the MENU button

Then press the METER button