Icom IC-2820H Instructions de montage

Prince William County ARES

IC-2820 Quick Reference Guide v.1.4

Icom IC-2820H Basic Operations

These instructions are not a substitute for reading the manual

NOTE: The IC-2820 is a dual receive radio with a left and right side and set of keys and

knobs. The active side is identified by a MAIN icon in the top “left” corner of the ac-

tive display. When the instructions refer to MAIN key or knob, they refer to the active

transceiver side and do not affect the inactive side until the inactive side is made active.

To select the MAIN band, either press the DIAL knob on the side you wish to set ac-

tive.

The IC-2820 has a magnetic attached face plate. The connector cable may not be attached to the radio initially (use the short one, not

the long extender cable). Note that the six-pin end goes into the main unit and the four-pin end goes into the face plate. The micro-

phone should already be attached and covered by a faceplate.

IC-2820 Front Panel: 1) Power, 2) Function/Lock key 3) Output Power/Priority, 4) Tone/DTMF, 5) Duplex/Monitor, (Button 2-5 are for

the MAIN band only), 6) SQL, 7) VOL, 8) DIAL, 9) MAIN band (push), 10) VFO/Tune/Scan, 11) Memory/Call/Memory write.

IC-2820 LCD Panel: Of note: 1) Operating mode indicator, 2) Duplex indica-

tors, 3) Name indicator if programmed, 4) Tone indicator, 5/6) Not relevant

without D-Star board, 10) Lock function enabled, 17) Weather indicators if

programmed, 19) Power level, 22) MAIN band indicator IC-2820 Main body: 1) Controller connector (6-

pin), 2) & 3) Not used, 4) Packet data jack, 5)

Mic, 6) Antenna (primary), 8) Antenna

(optional), 9) External speaker, 10) External

speaker—see External speakers.

Prince William County ARES

IC-2820 Quick Reference Guide v.1.4

Memory

Channel

Memory Name/Purpose Frequency Tone

1 OVH2M/Operations and Logistics 146.970 - 100 Hz

2 WWI2M/Operations and Logistics 147.240 +

3 NVFM2M/Fairfax ARES 146.790 -

4 NVREGN/Northern Virginia Regional Operations and

Coordination

146.910 -

5 SKYWARN/National Weather Service—Sterling 147.300 +

6 MDREGN/Maryland Regional Operation and Coordination 147.105 +

7 MTVERN/Mount Vernon (Alexandria) 146.655 - 141.3 Hz

8 ALEX2M/Alexandria ARES 147.315 +

9 ARL2M/Arlington ARES 145.470 -

10 FAQ2M/Fauquier ARES 147.470 + 167.9 Hz

11 LOU2M/Loudon ARES 145.310 -

12 DULLES/Dulles Airport 2m machine, max 15w out 147.330 + 203.5 Hz

21 OVH440/Command and Control/Operations and Logistics 442.200 +

22 WWI440/Command and Control/Operations and Logistics 444.900 +

23 FALLSC/Fall Church ARES 442.425 - 91.5 Hz

25 NERA/DC 449.975 - 107.2 Hz

26 KT4ER/Bull Run Mountain 448.325 - 100.0 Hz

33 MEDCOM/InterHospital communications/MedComm back-

146.445

34 ARC-CHP/Red Cross Chapter-to-Chapter communications 146.535

35 ARC-FLD/Red Cross Field Operations 146.420

36 XBAND1/Combine with 147.525—VHF1 (left) 445.950 (right) 100.0 Hz

37 XBAND2/Combine with 146.475—VHF2 (left) 446.050 (right) 100.0 Hz

38 XBAND3/Combine with 146.970—OVH2M (left) 445.975 (right) 100.0 Hz

39 XBAND4/Combine with 147.240—WWI2M (left) 446.025 (right) 100.0 Hz

40 Packet 145.730

41 APRS 144.390

24 NERA/Main Repeater, linked system 442.725 + 107.2 Hz

27 NERA/Bull Run Mountain 447.775 - 67.0 Hz

Preprogrammed Memory Channels and Frequencies

IC-2820

Prince William County ARES

IC-2820 Quick Reference Guide v.1.4

Band Management Selecting the Operating Band (Pg. X)

Transmission is possible on the side where the MAIN icon is lit.

To select the left or right side for transmission:

Mic: Press the BAND button

Face: Briefly press the MAIN-BAND knob on either the left or the right side as

needed.

Selecting the Frequency Band (Pg. XI)

Press and hold the DIAL knob for 1 second, then rotate the DIAL to step through the

bands.

Direct input with Mic (Pg. XI)

Push the VFO/LOCK button, push the T-OFF/ENT C button, push the number

buttons for the frequency.

Power Turning the power on and off (Pg. 15)

To turn the radio on, press and hold the

[PWR]

button

For 1 second (Fig. 1). The LCD will show the

current power supply voltage for 2 seconds before

switching to normal mode.

To turn the radio off, press and hold the

[PWR]

button

for 1 seconds.

Changing the Transmit Power Level (Pg. 23)

Press the [LOW-PRIO] to change the power output levels. Low is 5W, Mid is 15W,

High is 50W on 2M and 35W on 70cm.

Figure 1

Locking the Radio Locking the radio (Pg. 19)

Press the FUNCTION-LOCK key for 1 second to lock or unlock the frequency.

Memory Mode Memory Mode Operations (Pg. 61)

The IC-2820 deployed at the EOC and Potomac Hospital have been preloaded with the

frequencies listed in this guide. To ENTER memory mode:

1. Press M/CALL-MW button once. The MR icon appears on the active frequency.

You will need to do this for each active frequency once.

2. Turn the DIAL until the desired memory bank is displayed.

3. To enable the name function:

A. Push the FUNCTION key

B. Push the LOW-PRIO button once

C. Push the FUNCTION key twice to return to normal operations

Prince William County ARES

IC-2820 Quick Reference Guide v.1.4

CTCSS CTCSS Operations

Enabling CTCSS involves two steps. You have to set the Tone Frequency (Pg. 32) and

enable the Tone mode (Pg. 30).

Setting the Tone Frequency (Pg. 32)

1. Push the FUNCTION key to display the function guide.

2. Push the MENU (V/MHZ-SCAN) key (Far right).

3. Rotate DIAL to select DUP/TONE, then push MAIN-BAND.

4. Rotate DIAL to select REPEATER TONE then push MAIN-BAND.

5. Rotate DIAL to select the tone you want, and then push MAIN-BAND to set.

6. Push BACK (V/MHZ-SCAN) (far right) twice to exit and return to normal op-

erations

Enabling Tone Mode (Pg. 30)

1. Push TONE-DTMF to enable TONE. It rotates through TONE, T.SQL, and dis-

abled.

Repeater Offsets Setting Repeater Offsets (Pg. 30)

The IC-2820 comes preset with the following shifts: On 2m, 600 kHz; on 70cm, 5 MHz

To manually set the positive (+) or negative (-) or disable the offset, push the DUP-

MONI button to change between off, DUP-, and DUP+

This works ONLY for the active frequency.

Cross Band

Repeater

Operations

Enabling the cross band function (Icom KB 743G461664)

1. Configure the band(s) as needed with power levels and TONE as needed.

2. Press and hold both left and right MAIN dials then the FUNCTION key to-

gether. After two beeps, the lock key will flash in the upper right of the display.

3. When in cross band mode, the VHF frequency is on the left and the UHF fre-

quency is on the right.

4. Repeat step 2 to return to normal operations.

Autres manuels pour IC-2820H

Table des matières

Autres manuels Icom Émetteur-récepteur

Icom

Icom IC-F3 Manuel utilisateur

Icom

Icom IC-F30LT Manuel utilisateur

Icom

Icom IC-F3161T Manuel utilisateur

Icom

Icom IC-F3021T/S Manuel utilisateur

Icom

Icom IC-Q7A Manuel utilisateur

Icom

Icom IC-706 Manuel utilisateur

Icom

Icom IC-V86 Guide de configuration

Icom

Icom IC-745 Manuel utilisateur

Icom

Icom IC-A24 Manuel utilisateur

Icom

Icom IC-M56 Manuel utilisateur

Icom

Icom IC-M10E Manuel utilisateur

Icom

Icom IC-F1710 Manuel utilisateur

Icom

Icom ID-880H Manuel utilisateur

Icom

Icom IC-W31A Manuel utilisateur

Icom

Icom IC-V210T Manuel utilisateur

Icom

Icom IC-9700 Instructions d'installation et d'utilisation

Icom

Icom IC-2100H Manuel utilisateur

Icom

Icom IC-2200H Manuel utilisateur

Icom

Icom IC-F33GT Manuel utilisateur

Icom

Icom IC-M71 Manuel utilisateur

Icom

Icom IC-SAT100 Manuel utilisateur

Icom

Icom IC-M85 Manuel utilisateur

Icom

Icom IC-?2A/AT/E Manuel utilisateur

Icom

Icom IC-U16 Manuel utilisateur

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur