Icom Ic-2730A Manuel du propriétaire

©June 2016 Icom America Inc. Page 1

Icom America, Inc.

12421 Willows Road NE

Kirkland, WA 98034

IC-2730A Memory Channel Programming

This programming method uses the front panel keys.

What you will need:

•Operating frequency

•Offset direction (Duplex, for repeater use)

•Subaudible tone frequency for your repeater

Entering a Frequency

1. Press the Main/Band key to select the side of the display you wish to use (MAIN will appear on

the selected side).

2. Press the [V/MHz/Scan] key to place the radio in VFO mode.

3. Rotate the dial (for the side of the radio you selected) to enter your frequency.

4. Press [Menu] to enter the menu selection mode.

Selecting the Repeater Tone

1. Rotate the dial to select R TONE.

2. Press the Enter key (the key below a backwards-facing arrow: [MW]). You will see R TONE to

the left of the display and the value of the subaudible tone on the right side.

3. Rotate the dial to select the repeater tone.

4. Press the Enter key.

Turning on the Tone Encoder

Use the dial to select TONE and press the Enter key. The letter Twill appear on the display above the

frequency to show that the tone encoder is enabled.

Setting the offset (DUPLEX)

1. Press and hold the key labeled [MONI/DUP]. You will see an indication of the Duplex direction

(-, +or OFF).

2. Select the offset direction by rotating the dial.

3. When you have the correct offset direction, press the [MONI/DUP] key again.

©June 2016 Icom America Inc. Page 2

Icom America, Inc.

12421 Willows Road NE

Kirkland, WA 98034

Saving these settings to Memory

Your display should show your frequency, the duplex (DUP+or DUP-), and the Tfor tone encoder. To

save these settings to a Memory Channel, do the following:

1. Press the [MW] key.

2. MW will blink on the display.

3. Rotate your dial to display CH SEL (channel selection).

4. Press the Enter key.

5. Rotate the dial to the memory channel you wish to use.

6. Press the Enter key.

7. Rotate the dial to WRITE.

8. Press the Enter key.

9. The display will show WRITE.

10. Rotate the dial to YES.

11. Press the Enter key.

Verify the Programming

To check the memory channels, momentarily press the [MR/CALL] key and rotate the dial through the

memory channels and confirm that the repeater is programmed into the memory channel that you

selected.

Autres manuels pour ic-2730A

2

Table des matières

Autres manuels Icom Émetteur-récepteur

Icom

Icom IC-718 Manuel d'instructions

Icom

Icom iF110 Manuel utilisateur

Icom

Icom IC-F1010 Manuel utilisateur

Icom

Icom IC-A210E Manuel utilisateur

Icom

Icom IC-2700H Manuel utilisateur

Icom

Icom IC01271A/E Manuel utilisateur

Icom

Icom IC-3FGX Manuel utilisateur

Icom

Icom IC-F9511 Manuel utilisateur

Icom

Icom IC-M1V Manuel utilisateur

Icom

Icom IC-761 Mode d’emploi

Icom

Icom IC-A24E Manuel utilisateur

Icom

Icom IC-M302 Manuel utilisateur

Icom

Icom IC-4088SR Manuel utilisateur

Icom

Icom IC-F5010 series Manuel utilisateur

Icom

Icom IC-F29DR Manuel utilisateur

Icom

Icom IC-A23 Manuel utilisateur

Icom

Icom IC-F3161T Manuel utilisateur

Icom

Icom IC-3SAT Manuel utilisateur

Icom

Icom IC-E7 Manuel utilisateur

Icom

Icom IC-4088E Manuel utilisateur

Icom

Icom IC-7100 Manuel utilisateur

Icom

Icom IC-V80 Manuel utilisateur

Icom

Icom IC-F1100D Series Manuel utilisateur

Icom

Icom IC-F1700 Manuel utilisateur

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur