Icom rs-ba1 Manuel utilisateur
A-1
RS-BA1
Installation guide A
RS-BA1
Installation guide A
Form2001
This guide explains the minimum required settings to congure a remote control system, taking the following
illustration as an example. In this example, a radio is connected to the Base station’s PC with the supplied USB
cable, and a remote station remotely controls the radio through the network.
• We recommend that you place the Remote station’s PC near to the Base station's PC and a radio, to check that
the settings are correct, and that you can correctly control the radio.
• You need to register the ID and password to the Base station to enable the Remote station to access the Base
station and the radio. BE CAREFUL in managing IDs and passwords.
• See the Instruction Manual, for detailed instructions on the RS-BA1.
You can also refer to each software’s help le, for assistance with the functions and settings.
While the software is open, push the [F1] key of the PC’s keyboard to open the help le.
Example of the remote control system
* In this illustration, routers or other devices are not described.
RC-28
(Optional)
InternetInternet
Icom radio Base station Remote station
CI-V address : 94
Baud rate : Auto
PC Name : Base PC
IP address : 192.168.0.10
Computer name: BasePC
PC Name : User PC
User ID : USER1
Password : USER0001
USB cable
(Supplied to the
RS-BA1 or a radio)
Router
IC-7300
NOTE:
The password, and other settings in this illustration
are only an example. Please congure the system
using your own settings.
For your convenience:
If you connect an RC-28 remote encoder to the
Remote station, you can use the RS-BA1 and feel
like you are operating the actual transceiver’s main
dial, [TRANSMIT] key and so on.
This guide contains instructions on how to congure the remote control system, and how to remotely control a
radio.
If you are using one of the following radios and connecting to the network directly, see the Installation guide B
(For radios with the Network function). (As of August 2017)
• IC-7851
• IC-7850
• IC-7800 (Firmware version 3.00 or later)
• IC-7700 (Firmware version 2.00 or later)
• IC-7610
Before reading this guide, please nish the installation, using the RS-BA1 Preparations.
See the RS-BA1 Instruction Manual for detailed instructions.
Installtion guide A
A-2
Step1. Connect the radio to the Base station's PC
Before connecting the radio to the PC, please nish the installation for the Base station's PC and the Remote
station's PC, using the RS-BA1 Preparations.
Step1. 2. 3. 4. 5. 6.
The Network function enables the radio to directly connect to the network. With this function, the base station PC is not
necessary. See the Installation guide B (For radios with the Network function).
Radios with the Network function (As of August 2017)
• IC-7851
• IC-7850
• IC-7800 (Firmware version 3.00 or later)
• IC-7700 (Firmware version 2.00 or later)
• IC-7610
Check the connector type on your radio and see the following chart to connect your radio to the Base station’s
PC.
To connect an Icom CI-V command capable radio to the Base station’s PC, you have to make connections for
control command and audio communication.
RS-BA1 operation with the Base station’s PC connected to the radio’s ACC socket, MIC connector, or S/P DIF
jack for audio communication cannot be guaranteed.
• This guide explains the USB connection as example. See the RS-BA1 Instruction Manual (“2. WHEN
CONNECTING TO THE NETWORK THROUGH A PC” section) when connecting to the radio's [REMOTE] jack
or [RS-232C] port.
Radio's connector
Outline
Model Ref.
Control command Audio
When connecting to the
radio's [USB] port Through a USB cable
IC-7100/IC-7200/
IC-7300/IC-7410/
IC-7600*1/IC-7610/
IC-7850/IC-7851/
IC-9100
p. A-3
When connecting to the
radio's [REMOTE] jack
Through the CT-17 ci-v
level converter
Through an audio cable connected between
the PC’s audio terminal and the radio’s [ACC]
socket or [MIC] connector
All
RS-BA1
Instruction
Manual
When connecting to the
radio's [RS-232C] port
Through an RS-232C
cable
Through an audio cable connected between
the PC’s audio terminal and the radio’s [ACC]
socket, [MIC] connector or [S/P DIF] jack
IC-7700/IC-7800*2
RS-BA1
Instruction
Manual
Select the connection pattern
*1 When you turn your radio ON or OFF from the Remote Controller, connect to the radio's [Remote] jack.
*2 When you turn your radio ON or OFF from the Remote Controller, connect to the radio's [Remote] jack or to the network
directly.
RC-28
(Optional)
Remote station
Base station
Connect to
the LAN port
A radio with the ser
ver function
Router
InternetInternet
Installtion guide A
A-3
Step1. Connect the radio to the Base station's PC (Continued)
DWhen connecting to the radio’s [USB] port
For IC-7600 users
When you turn your radio ON or OFF from the Remote Controller, connect to the radio's [Remote] jack.
1. System requirements
• A PC that has a USB 1.1, 2.0 or 3.0 port
• Icom CI-V command capable radio that has a [USB]
port (Type B/Mini-B)
• The USB cable (supplied to the RS-BA1 or a radio)
2. Install a USB driver
CAUTION:
• NEVER connect the radio to the PC with the USB
cable until the USB driver installation has been
completed.
• The driver is not supported by the Windows®
automatic recognition system.
To use the USB cable between the radio and the PC,
you must rst install a USB driver.
• The USB driver comes with the RS-BA1. Or
download from the Icom website.
NOTE: When a PC with USB 3.0 port is used for
operating the radio, conrm the driver name. If
the name “Silicon Laboratories CP210x USB to
UART Bridge (Driver Removal)” is displayed on the
Control Panel screen, uninstall it and then install
the latest driver.
The latest driver and installation guide can be
downloaded from here:
http://www.icom.co.jp/world/index.html
Read the installation guide before installing the driver.
3. Connect the radio to the Base station’s PC
Connect the radio to the Base station’s PC using the
USB cable.
• This guide is based on using a Type B USB cable.
USB cable
Radio
(Rear panel)
PC
To
the USB port
To a USB port
ACC
KEY
12
METER
REMOTE
Step1. 2. 3. 4. 5. 6.
NOTE: If you connect a new USB audio device
to your PC, the device selected as the default on
your PC can be changed. Moreover, never connect
another radio using a USB cable while the Remote
Utility is open.
Installtion guide A
A-4
Step2. Radio’s presettings
The RS-BA1 remotely controls Icom radios using CI-V (Icom Communication Interface) commands. See the CI-V
command table in the radio’s instruction manual for details of the functions that can be controlled.
1. The following manual settings are required when operating the RS-BA1
Properly preset the items in below table for functions that cannot be controlled by CI-V commands or the item
may cause unwanted actions. See the radio’s instruction manual for details of the settings or operation.
NOTE:
• Remove the transverter from the radio, if it is connected.
• To prevent an accidental transmission, we recommend you remove any keyer, keypad or other external
equipment connected to the radio.
• Set the radio to a normal operating mode. The radio cannot receive CI-V commands while in special modes,
such as the rmware update mode or cloning mode.
• If the radio has a Time-Out Timer function, we recommend you enable it to prevent the radio from continuously
transmitting.
1. Step2. 3. 4. 5. 6.
If you are using the IC-PW1 with the transceiver, be sure to set the CI-V baud rate to 19200 bps. After changing
the transceiver’s CI-V settings, be sure to reset the CPU of the IC-PW1 and set the transceiver’s CI-V settings
on the IC-PW1. See the IC-PW1 instruction manual for details.
Genre Item Model Setting
Function RIT function All Set to OFF.
∂TX function All Set to OFF.
Simple band scope IC-746PRO*/IC-7000*/IC-7100/IC-7400*/IC-9100 Set to OFF.
SWR Measurement function IC-746PRO*/IC-7000*/IC-7100/IC-7400*/IC-9100 Set to OFF.
Timer/Sleep Timer function Radios with the timer function Set the timer to OFF or to your schedule.
Weather Alert function IC-7100 Set to OFF.
Display RTTY decode screen IC-746PRO*/IC-756PROIII*/IC-7400* Exit the screen.
Volume Volume for the RX audio All Set the volume to a suitable level.
CI-V CI-V address All Set an appropriate CI-V address.
CI-V baud rate All Set to 19200 bps (or Auto).
CI-V USB Port IC-7300/IC-7610/
IC-7850 (Firmware version 1.10 or later)/
IC-7851 (Firmware version 1.10 or later)
To use the Scope function when
connecting to the USB port, set to Unlink
from [REMOTE].
CI-V USB Baud Rate IC-7300/IC-7610/
IC-7850 (Firmware version 1.10 or later)/
IC-7851 (Firmware version 1.10 or later)
To use the Scope function when
connecting to the USB port, set to
115200 (or Auto).
Set mode USB Serial Function Radios with a USB (B type) port Set to “CI-V” for the selected connection
type.
RS-232C Function Radios with an RS-232C port Set to “CI-V” for the selected connection
type.
* Operation on models without a USB connection cannot be guaranteed.
Installtion guide A
A-5
Step2. Radio’s presettings (Continued)
2. The following settings are automatically set to the radio
When the RS-BA1’s Remote Controller connects to the radio, and you select the model name on the Connect
Setting screen, the following may be automatically set, depending on the model. When you manually operate the
radio, set these items as desired.
Genre Item Model Action
Function MAIN/SUB Tranking function IC-7610/IC-7850 (Firmware version 1.10 or
later)/
IC-7851 (Firmware version 1.10 or later)
Automatically set to OFF.
RIT function Radios with the Network function/
IC-7100 (Firmware version 1.10 or later)/
IC-7600 (Firmware version 2.00 or later)
Automatically set to OFF.
∂TX function Radios with the Network function/
IC-7600 (Firmware version 2.00 or later)
Automatically set to OFF.
SSB/CW Synchronous Tuning All Automatically set to OFF.
Calibration Marker Radios with Calibration Marker function Automatically set to OFF.
VOX function All Automatically set to OFF.
Scan function All Automatically cancel the scan.
RTTY lter IC-746PRO*/IC-756PROIII*/IC-7400* Automatically set to OFF.
Twin Peak Filter IC-746PRO*/IC-756PROIII*/IC-7400* Automatically set to OFF.
Display Dualwatch function Radios with the Dualwatch function Automatically set to OFF.
SUB band IC-9100 Automatically set to OFF.
Memory channel/Call channel All Automatically set to the VFO mode.
Operating
mode
DR (D-STAR® REPEATER)
mode
Radios with the DV mode Automatically set to OFF.
Satellite mode Radios with the Satellite mode Automatically set to OFF.
CI-V CI-V transceive All Automatically set to ON.
CI-V 731 Mode IC-746PRO*/IC-756PROIII*/IC-7400* Automatically set to OFF.
*
Operation on models without a USB connection cannot be guaranteed.
1. Step2. 3. 4. 5. 6.
Installtion guide A
A-6
Step3. Before conguration
To congure the remote control system, the following settings are required.
DFirewall setting (RS-BA1 Instruction Manual p. 1)
To let the Remote Utility work properly, it must be added as an exception in the Firewall. See the RS-BA1
Instruction Manual for details.
DVolume adjustment for your audio devices (RS-BA1 Instruction Manual p. 6)
Before you start communicating using the RS-BA1, the PC’s audio volume must be set to a proper level.
When your PC is used as a Base station, adjust the audio level of the device that is connected to your radio.
When your PC is used as a Remote station, adjust the audio level of the device that your microphone, speaker,
or headset is connected to.
DTo allow access from the Internet (RS-BA1 Instruction Manual p. 12)
If you congure the remote control system through the Internet, you need to congure your Base station and
Remote station routers to allow access from the Internet.
Congure the port forwarding settings, and IP lter settings on your router, for port numbers 50001, 50002, and
50003 which are used for the Remote Utility.
See your router’s manual for details of how to congure the settings.
See the RS-BA1 Instruction Manual (“1. BEFORE USING REMOTE CONTROL SYSTEM” section) for details.
1. 2. Step3. 4. 5. 6.
Installtion guide A
A-7
Step4. Settings on the Base station’s PC
This section describes how to setup the Base station (Server) PC. Before conguring the settings, turn on the
radio.
See the RS-BA1 Instruction Manual (“2. WHEN CONNECTING TO THE NETWORK THROUGH A PC” section)
for details.
1. 2. 3. Step4. 5. 6.
1Open the Remote Utility.
1. Double-click the “Remote Utility” icon on
your desktop to open the Remote Utility.
2. “Please set your own PC information” is
displayed, then click <OK>.
LWhen you rst open the Remote Utility, this
screen is displayed.
2Congure the settings.
LWhen you rst open the Remote Utility, this screen
is displayed.
Click <OK>, and then restart the Remote Utility.
3
Click
1Enter
2Conrm
3Select
4Select
5Click
6Click
Click the Setup that you want to do.
LIf no Servers and no radios are registered, this
screen is displayed.
Click
4Start the Setup Wizard.
Click
5Select a Radio for the Remote operation.
1Select
2Click
Installtion guide A
A-8
Step4. Settings on the Base station’s PC (Continued)
1. 2. 3. Step4. 5. 6.
6Select a Radio.
7Set the CI-V/COM port settings.
Click
1Select
2Click
LIf the radio is not listed, click the <Search>
button.
LIf the radio is connected to the PC using other
than a USB cable, select from the Manual
drop-down list.
If the radio is connected to the PC using other
than a USB cable, the Audio Settings screen is
displayed.
Select the devices that input a received audio from
the radio and output a modulation to the radio, and
then click <Next>>.
8Register a User to accept connection.
1Click
2Enter
3Enter
4Click To set the user as
an administrator,
click to make a
check mark.
5Click 6Click
7Click
To prevent unauthorized access:
Set a long and strong password so that no one can
possibly guess it.
Mix upper and lower case letters, numbers or
characters.
(Example:
USER0001)
Installtion guide A
A-9
Step4. Settings on the Base station’s PC (Continued)
1. 2. 3. Step4. 5. 6.
9Enter the radio name.
Click
LThe radio’s model name and the last 5 gures
of the serial number is entered by default.
10 The registration of the Radio is completed.
Click
By connecting the Radio to a USB port, the
default settings on the REC/PLAY device
window may change to the Radio’s Speaker
and Microphone. To conrm the settings, click
<Sound Settings>.
Installtion guide A
A-10
Step5. Settings on the Remote station’s PC
This section describes how to setup the Remote station (Client) PC.
Before conguring the settings, connect a speaker and microphone, or headset to the Remote station’s PC.
See the RS-BA1 Instruction Manual (“4. SETTINGS FOR A REMOTE STATION PC” section) for details.
1. 2. 3. 4. Step5. 6.
1Open the Remote Utility.
1. Double-click the “Remote Utility” icon on
your desktop to open the Remote Utility.
2. “Please set your own PC information” is
displayed, then click <OK>.
LWhen you rst open the Remote Utility, this
screen is displayed.
2Congure the settings.
LWhen you rst open the Remote Utility, this screen
is displayed.
Click <OK>, and then restart the Remote Utility.
3
Click
1Enter
2Conrm
3Select
4Select
5Click
6Click
Click the Setup that you want to do.
LIf no Servers and no radios are registered, this
screen is displayed.
Click
4Start the Setup Wizard.
Click
5Enter the Server Information.
1Enter
2Click
Autres manuels pour rs-ba1
3
Table des matières
