ICM Controls ICM2805A Instructions générales

 Thisboardshouldbeinstalledbyaqualiedtechnician

only.Failuretofollowtheseinstructionscouldleadto

propertydamage,personalinjuryordeath.

 Disconnectthepowersupplybyturningoffacircuit

breakerorremovingafusebeforeattemptingtoinstall

thisboard.

1.Turnoffthepowersupplytothefurnacebyremovingthefuseor

turningoffthecircuitbreaker.

2.Removethewiresandconnectorsfromtheoldboardoneat

atime.CarefullyconnectthemtotheICM2805Atopreventa

miswire.Removethemountingscrewsandthenremovetheold

controlboard.

3.Placethetemplate(onthebackofthissheet)inthecontrolbox

andsecurewithtape.Moveallwiresoutofthewayandcarefully

drillfour3/16”diameterholesasshownonthetemplate.

Removeanddiscardthetemplate.

4.MounttheICM2805Awiththefuseatthetopbyinsertingthe

standoffsintothemountingholes.

NOTE:Do not ex the ICM2805A circuit board. Apply pressure

only at the standoffs.

5.Disconnectthe6-pinconnectorplug.UsinganAMPextractor

tool#458994-2removethebluewirefromsocketposition#4

andinstallitinposition#1.(seediagramatright).Ifthetoolis

notavailableproceedasfollows:

 Cutoffthebluewireatsocketposition#4intheconnector(see

diagramatright),andstriptheinsulationback3/8”.Insertthe

lengthofbluewireprovidedinsocketposition#1,nexttothecut

offbluewire.Reconnectthe6-pinconnectorplug.Connectthe

looseendsofthebluewiresusingthewirenutprovided.Tape

thewirenutconnectionwithelectricaltapesoitcannotloosen.

6.ApplythenewwiringdiagramforG4furnacessuppliedwiththe

ICM2805Atotheinsideofthecabinet.

7.Turnonthepowersupplyandcheckthefurnaceforproper

operation.

G3RC and G4 Furnace Models

ICM2805A 1.Turnoffthepowersupplytothefurnacebyremovingthefuseor

turningoffthecircuitbreaker.

2.Removethewiresandconnectorsfromtheoldboardoneat

atime.CarefullyconnectthemtotheICM2805Atopreventa

miswire.Removethecontrolbracketmountingscrewsfrom

theoutsideofthecabinet(exceptG5RLmodels).Installthe

newcontrolbracketandthenproceedtostep4.Ifthescrews

arenotaccessible,newmountingholesmustbedrilledinthe

existingmountingbracketusingthetemplateonthebackofthis

instructionsheet.

3.Removethescrewsecuringtheoldcontrolboardandthen

removetheoldcontrolboard.Placethetemplate(onthebackof

thissheet)overthemountingbracketandsecurewithtape.Move

allwiresoutofthewayandcarefullydrillfour3/16”diameterholes

asshownonthetemplate.Removeanddiscardthetemplate.

4.MounttheICM2805Awiththefuseatthetopbyinsertingthe

standoffsintothemountingholes.

NOTE:Do not ex the ICM2805A circuit board. Apply pressure

only at the standoffs.

5.ApplythenewwiringdiagramforG5furnacessuppliedwiththe

ICM2805Atotheinsideofthecabinet.

6.Turnonthepowersupplyandcheckthefurnaceforproper

operation.

G5 Furnace Models

1.Turnoffthepowersupplytothefurnacebyremovingthefuseor

turningoffthecircuitbreaker.

2.Removethewiresandconnectorsfromtheoldboardoneat

atime.CarefullyconnectthemtotheICM2805Atopreventa

miswire.

3.Removetheoldboardbycuttingoffthestandoffs.Installthe

ICM2805Ainthesamepositionbysnappingthestandoffsintothe

mountingholes.

 NOTE:Do not ex the ICM2805A circuit board. Apply pressure

only at the standoffs.

4.Turnonthepowersupplyandcheckthefurnaceforproper

operation.

G6, M2 & M3 Furnace Models

6-pinwireconnector

Whitewire

Blackwire

Bluewirecut

InsertedBluewire

(provided)

ExistingBluewire

(Previouslycutfromslot4)

Whitewire

Blackwire

ExistingBluewire

(Tobecut&connected

towireprovided)

Cutexistingblue

wirehere

InsertBluewire

(provided)

6-pinwireconnector

7313WilliamBarryBlvd.,NorthSyracuse,NY13212

(TollFree)800-365-5525(Phone)315-233-5266(Fax)315-233-5276

www.icmcontrols.com

ONE-YEAR LIMITED WARRANTY

TheSellerwarrantsitsproductsagainstdefectsinmaterialorworkmanshipforaperiodofone(1)

yearfromthedateofmanufacture.TheliabilityoftheSellerislimited,atitsoption,torepair,replace

orissueanon-casecreditforthepurchasepricesofthegoodswhichareprovidedtobedefective.

Thewarrantyandremediessetforthhereindonotapplytoanygoodsorpartsthereofwhichhave

beensubjectedtomisuseincludinganyuseorapplicationinviolationoftheSeller’sinstructions,

neglect,tampering,improperstorage,incorrectinstallationorservicingnotperformedbytheSeller.

InordertopermittheSellertoproperlyadministerthewarranty,theBuyershall:1)NotifytheSeller

promptlyofanyclaim,submittingdatecodeinformationoranyotherpertinentdataasrequestedby

theSeller.2)PermittheSellertoinspectandtesttheproductclaimedtobedefective.Itemsclaimed

tobedefectiveandaredeterminedbySellertobenon-defectivearesubjecttoa$30.00perhour

inspectionfee.ThiswarrantyconstitutestheSeller’ssoleliabilityhereunderandisinlieuofanyother

warrantyexpressed,impliedorstatutory.Unlessotherwisestatedinwriting,Sellermakesnowarranty

thatthegoodsdepictedordescribedhereinaretforanyparticularpurpose. LIAF117-1

G5RLModels:Foldbackonline

G5RLModelsonly:Foldpaperbackalongdashedlineandplacethis

corneronlower-leftcornerofmontingpanel.

AllG4andG5furnaces,exceptG5RLModels:

Placethiscornerofthetemplateinthecornerofthecontrolbox,nexttocutout(G4),

oronlower-rightcornerofmountingpanel(G5)

Unsethistemplateto

carefullydrill(4)3/16”holes.

ICM2805A Fault Codes

LED’S Flashes FaultCondition

Red ON Normaloperation

1Flash Limitswitchesopen

2Flashes Pressureswitchstuckopen

3Flashes Pressureswitchstuckclosed

4Flashes Ignitionfailure(5trials)

5Flashes HotandNeutralreversedornoground

6Flashes Brownoutvoltage

Continuous FaultameorGasvalverelayshort

Yellow Continuous LowameorNoame

ON Flamepresent

Thiscontrolhasbuilt-inself-diagnosticcapability.Ifasystemproblemoccurs,ablinkingLEDshowsafaultcode.

Autres manuels ICM Controls Système de contrôle

ICM Controls

ICM Controls ICM2813 Instructions générales

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur