Icle bubba Moon Manuel utilisateur
Moon
Contents
Page 03
Components
Page 04
Warnings
Page 05
Assembly: Parts & Opening
the Frame
Page 06
Assembly: Installing the Rear
Wheels
Page 07
Assembly: Installing the Front
Wheels & Using the Bumper Bar
Page 09
Assembly: Installing the Pram
Hood & Preparing the Seat Unit
Page 08
Assembly: Using the Harness &
Adjusting the Harness Height
Page 10
Assembly: Attaching Seat Unit to
Pram& Converting Pram Mode to
Seat Unit
Page 12
Operating the Seat Recline &
Folding the Frame
Page 13
Operating the Tether Strap &
Care and Maintenance
IMPORTANT! READ THE INSTRUCTIONS CAREFULLY BEFORE USE AND
KEEP THEM FOR FUTURE REFERENCE.
Page 11
Operating the Brakes &
the Front Wheel Lock
Page 14
Warranty Information
V.02.21
2
5
Components
1
2
3
5
6
7
8
1
23
7
6
4
* Not Pictured
8
4
10
11
13
12
Folding Button
Hood
Seat Recline
Seat Unit Toggle
Bumper Bar
Bumper Bar Release
5 Point Safety Harness
Seat/Pram Body
9
9 Convertible Pram Body
& Seat Unit
10 Shopping Basket
11
Built in Supension
12 Rear Wheels
13 Brake
14 Seat/Pram Body Apron*
15 Raincover*
16 Wrist Strap
16
*
Removal Button
V.02.21
3
WARNINGS!
IMPORTANT: Read these instructions carefully before
use and keep them for future reference.
The Moon pushchair in pram mode is suitable for children from birth up to a
maximum weight of 9kgs.
The Moon pushchair in seat mode is suitable for children from 6months up
to a maximum weight of 20kgs.
V.02.21
WARNING: TO AVOID INJURY OR DEATH: ALWAYS APPLY THE BRAKES
WHENEVER THE PRAM/STROLLER IS STATIONARY.
• DO NOT LEAVE CHILDREN UNATTENDED.
• SECURE THE CHILD IN THE HARNESS AT ALL TIMES.
• DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS PRAM/STROLLER.
• MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU ADJUST
THE PRAM/STROLLER.
WARNING: USE THIS HARNESS AT ALL TIMES.
WARNING: USE THIS STRAP TO STOP THE PRAM/STROLLER ROLLING AWAY.
This stroller has been designed for use on flat or gently slopped surfaces. Using
this stroller on uneven or higher sloped surface may cause the stroller to become
unstable and tip over.
WARNING Ensure that all locking devices are engaged before use.
WARNING Use the tether strap to prevent the stroller rolling away.
WARNING Never leave safety harness connected when not fitted to a child in the
stroller, as this may create loops that cause a strangulation hazard.
WARNING Fingers or parts of the body could be injured when the stroller is being
folded or unfolded. Please use caution when folding or unfolding the stroller.
WARNING To avoid injury ensure that your child is kept away when folding and
unfolding the stroller.
WARNING Never leave a child in the pram/stroller when ascending or descending
stairs or escalators. Use great care when using the stroller on other moving
surfaces.
WARNING Do not allow children to stand on the seat or footrest.
WARNING Do not attempt to lift the stroller by the bumper bar.
WARNING Engage front wheel swivel locks when travelling on rough or uneven
surfaces.
WARNING Regularly inspect all parts and locking devices, promptly replace worn
out or broken parts.
WARNING Use only those accessories which are supplied by Ickle Bubba and
approved for use with this stroller.
WARNING To prevent the risk of the stroller catching fire, do not park it near an
open fire, heater or barbecue.
WARNING Do not run or jog with this stroller.
WARNING Shopping basket capacity should not be more than 3kg.
THE MOON PRAM HAS BEEN APPROVED IN ACCORDANE TO
AS/NZS 2088 : 2013
4
Assembly - Parts
1. Chassis Frame 2. Seat Unit/Pram Body
3. Bumper Bar
4. Front Wheels
5. Rear Wheels
6. Rear Wheel Axle
& Break
9. Footmu
7. Rear Wheel
Hub Caps
8. Rear Wheel
Locking Caps
Assembly - Opening the Frame
1. Unhook the latch, located on
the right hand side of the frame
2. Lift the handlebar in the
direction of the arrow until the
frame locks into place.
V.02.21
5
Assembly - Installing the Rear Wheels
1. Insert the axle through each
rear wheel, with the axle going
through the break cluster on
the wheel first.
2. Fix the smallest locking cap
at the end of the axle to lock
the wheel on, then repeat with
the hub cap. Repeat this for
both wheels, ensuring both
sides are securely locked in
place.
3. Once the wheels are fixed
onto the axle, place the axle
onto the frame of the chassis.
Push it upwards until you hear a
‘click’ on both sides
4. To remove the rear wheel
axle, push both the metal push
pin clips inward, and slide
downwards until the axle is
clear of the chassis.
V.02.21
6
Assembly - Installing the Front Wheels
1. Push each front wheel onto
the front wheel bayonet until
you hear a ‘click’. Ensure it is
securely attached to the stroller
before use.
2. To remove the front wheels,
locate the release button which
can be found at the top of the
wheel bayonet, on the inner
side. Push the button in firmly
and the wheel will disengage.
Release
Button
Assembly - Using the Bumper Bar
1. Align the bumper bar with the
fitting on the frame and push
inwards until you hear a ‘click’
on each side and see the safety
release buttons are in the raised
position.
2. To remove, press each of the
safety release buttons (indicat-
ed above) and pull the bumper
bar outwards.
V.02.21
7
Assembly - Using the Harness
1. Insert both
shoulder strap
fasteners securely
into the loops
located on the side
straps
2. Press the two
side straps into the
centre clasp until
both sides are clicked
in securely. Adjust
each strap length as
required.
3. To undo the
harness, press the
buckles in the centre
of the harness and
pull apart.
1. The harness
can be set at three
heights
3. Secure the
harness.
Adjusting Harness Height
2. To use the slot, and
slots to undo the buckle
and feed the shoulder
straps in through the
chosen loop.
V.02.21
8
1. Insert the
metal frame of the
hood into the
corresponding re-
ceptors located on
the pram frame.
3. To remove the
hood, unfasten the
zip, then press
both of the
hood connector
but-tons and pull the
metal hood frame
upwards.
Assembly - Installing the Pram Hood
2. Align the zip located
on the rear side of the
hood to the zip found
on the pram/seat
unit fabric and fasten.
Assembly - Preparing the Seat Unit
1. Firstly, locate the seat
unit support.
2. Align either side of the
support with the two holes
situatied on both sides of
the inner seat frame.
Ensure that the support
is facing downwards and
towards the lower end of
the seat frame.
3. Push the support into
the holes and secure in
place with the two push
press clips located on
the seat unit fabric.
V.02.21
9
1. Align the seat unit
adapters with the cor-
responding holders on
the pram frame
3. To remove the seat
unit, press the release
buttons on both sides
of the seat frame and
lift the seat upwards.
Assembly - Attaching Seat Unit to Pram
2. Push the seat unit
downwards until both
sides ‘Click’. Ensure that
the seat is securely fas-
tened before use.
1. To use the seat unit in
pram mode, discon-
nect the two clips locat-
ed at the bottom of the
seat unit, and loosen the
toggle at the top. Push
the fabric downwards
from the inside to en-
sure it lies flat.
2. To convert pram
body to seat unit,
connect the two clips
located at the bottom
of the pram body/seat
unit
3. Tighten the tog-
gle located on the
top of the pram
body/seat unit. Ensure
that all fabrics and
buckles are secure
before use.
Assembly - Converting Pram to Seat
V.02.21
10
Table des matières
Autres manuels Icle bubba Poussette
