IBM Flex System EN2092 Manuel utilisateur

Configuring the IBM Flex System EN2092 1Gb Ethernet Sc l ble Switch

Prerequisites:

One IBM Flex System Enterprise Chassis, one IBM Flex System EN2092 1Gb Ethernet S alable

Swit h installed in I/O module bay 1 or 2.

An Ethernet network is already onfigured.

Steps:

Note: This pro ess illustrates how to enable the swit h ports through the Chassis Management Module

(CMM) ommand-line interfa e. For information about using the CMM interfa e, you an use the

“Configuring IBM Flex System Enterprise Chassis omponents” qui k start guide. You an find that qui k

start guide at this lo ation:

In the information enter (Internet):

http://pi .dhe.ibm. om/info enter/flexsys/information/topi / om.ibm.a . ommontasks.do / ommonta

sks_ hassis_ onfig.html

The IBM Flex System produ t do umentation is also available on the IBM Flex System Manager management node. To a ess

the installed do umentation, li k Information Center from the IBM Flex System Manager Home page and then navigate to:

IBM Flex System information -> Qui k start guides -> Installing and onfiguring the IBM Flex System Enterprise Chassis

1. Log on to the Chassis Management Module (CMM) CLI with an SSH appli ation. The default IP

address is 192.168.70.100 and the default login/password is USERID/PASSW0RD. If ne essary, obtain

the IP address and login of the CMM from your system administrator.

2. Set the environment to the bay where you installed the swit h. The following example is for bay 2:

env -T system:swit h[2]

3. Run the following ommand to enable external data ports:

if onfig -ep enabled

External ports 1 – 10 are now enabled for data throughput.

Page 1 of 2

Activating additional keys:

If you have pur hased additional keys, they need to be installed on the swit h. Complete the following

steps to install additional keys using the ISCLI interfa e.

1. To retrieve the key, navigate a browser to https://www.ibm. om/systems/x/fod/index.wss and sign in

with your ID and password

2. Cli k Request activation key.

3. Enter the authorization ode. The authorization ode was supplied to you by email or on paper as

part of the ordering pro ess.

4. Cli k Continue and follow the instru tions and download the key file.

5. Log on to the EN2092 swit h with an SSH appli ation. The default IP addresses for the swit h

through the CMM are as follows: 192.168.70.120 (bay 1), 192.168.70.121 (bay 2), 192.168.70.122

(bay 3), and 192.168.70.123 (bay 4). If ne essary, obtain the IP address and login of the swit h from

your system administrator.

6. Enter ena.

7. Enter software-key.

8. Enter enakey address <hostname or IP address> keyfile <file name>

protocol tftp mgt-port

Note: you must reset the swit h to apply the key.

9. Reset the swit h. Enter reload..

Repeat the step for additional keys if needed. The sequen e of steps is shown here:

Router#ena

Router(config)#software-key

Router(Software-Key)#enakey address 9.44.143.206 keyfile

ibm_fod_0007_ 010CM28N001_anyos_noarch.key protocol tftp mgt-port

Starting download key file...

Key file download complete (494 bytes)

Software feature Upgrade1 will be Active upon next reboot.

Aug 5 11:47:39 1080:0:0:0:0:0:0:82 NOTICE mgmt: Software feature Upgrade1

will be Active upon next reboot.

A Reboot is required for the new settings to take effect.

Router(Software-Key)#reload

...

Resetting at 11:47:59 Tue Aug 5, 2014...

Page 2 of 2

Autres manuels pour Flex System EN2092

Table des matières

Autres manuels IBM Changer

IBM

IBM Rack-Based Local Console Switches Manuel utilisateur

IBM

IBM System Storage SAN80B-4 Manuel utilisateur

IBM

IBM Nways 8260 Manuel utilisateur

IBM

IBM SAN40B-4 - System Storage Switch Manuel utilisateur

IBM

IBM BNT Manuel utilisateur

IBM

IBM F16 Manuel utilisateur

IBM

IBM BNT RackSwitch G8124 Manuel utilisateur

IBM

IBM 3454-CAC Manuel utilisateur

IBM

IBM Nways 8271 F12 Manuel utilisateur

IBM

IBM SAN32M1 Manuel

IBM

IBM Global console manager Manuel utilisateur

IBM

IBM 8271 Nways Ethernet LAN Switch Manuel utilisateur

IBM

IBM N Series Manuel utilisateur

IBM

IBM BNT RackSwitch G8124R Manuel utilisateur

IBM

IBM 8270 Instructions d'installation et d'entretien

IBM

IBM TotalStorage L10 Manuel utilisateur

IBM

IBM 8270 600 Manuel utilisateur

IBM

IBM RackSwitch G8264CS Manuel utilisateur

IBM

IBM CN4093 Manuel utilisateur

IBM

IBM J48E Manuel utilisateur

IBM

IBM 8285 Nways Manuel utilisateur

IBM

IBM 8265 Mode d'emploi

IBM

IBM SAN48C-6 Manuel

IBM

IBM BNT G8124 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur