IBM N6270 Manuel utilisateur

IBM System Storage

N6200SeriesHardwareandServiceGuide

CoveringtheN6210,N6220,N6240,N6250,andN6270models

GA32-0838-04



Note:

Before using this information and the product it supports, be sure to read the general information in “Notices” on page 109.

The following paragraph does not apply to any country (or region) where such provisions are inconsistent with

local law.

INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION “AS IS” WITHOUT

WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states (or

regions) do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement

may not apply to you.

Order publications through your IBM representative or the IBM branch office serving your locality.

US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract

with IBM Corp.

Safety notices

This section contains information about:

v“Safety notices and labels”

v“Laser safety” on page vii

v“Rack safety” on page viii

v“Fire suppression systems” on page xi

For information about environmental notices, see the IBM®Environmental Notices

and User Guide, Z125-5823.

Safety notices and labels

When using this product, observe the danger, caution, and attention notices

contained in this guide. The notices are accompanied by symbols that represent the

severity of the safety condition.

The following sections define each type of safety notice and provide examples.

The following notices and statements are used in IBM documents. They are listed

below in order of increasing severity of potential hazards. Follow the links for

more detailed descriptions and examples of the danger, caution, and attention

notices in the sections that follow.

“Danger notices”

These statements indicate situations that can be potentially lethal or

extremely hazardous to you. Safety labels are also attached directly to

products to warn of these situations.

“Caution notices” on page vi

These statements indicate situations that can be potentially hazardous to

you.

“Attention notices” on page vi

These notices indicate potential damage to programs, devices, or data.

Notes These notices provide important tips, guidance, or advice.

In addition to these notices, “Labels” on page v may be attached to the product to

warn of potential hazards.

Danger notices

A danger notice calls attention to a situation that is potentially lethal or extremely

hazardous to people. A lightning bolt symbol accompanies a danger notice to

represent a dangerous electrical condition. A sample danger notice follows.

DANGER

An electrical outlet that is not correctly wired could place hazardous

voltage on metal parts of the system or the devices that attach to the

system. It is the responsibility of the customer to ensure that the

outlet is correctly wired and grounded to prevent an electrical shock.

(D004)

A general danger notice provides instructions on how to avoid shock hazards

when servicing equipment. Unless instructed otherwise, follow the procedures in

the following danger notice.

iv IBM System Storage: N6200 Series Hardware and Service Guide

DANGER

When working on or around the system, observe the following precautions:

Electrical voltage and current from power, telephone, and communication

cables are hazardous. To avoid a shock hazard:

vConnect power to this unit only with the IBM provided power cord. Do

not use the IBM provided power cord for any other product.

vDo not open or service any power supply assembly.

vDo not connect or disconnect any cables or perform installation,

maintenance, or reconfiguration of this product during an electrical storm.

vThe product might be equipped with multiple power cords. To remove all

hazardous voltages, disconnect all power cords.

vConnect all power cords to a properly wired and grounded electrical

outlet. Ensure outlet supplies proper voltage and phase rotation according

to the system rating plate.

vConnect any equipment that will be attached to this product to properly

wired outlets.

vWhen possible, use one hand only to connect or disconnect signal cables.

vNever turn on any equipment when there is evidence of fire, water, or

structural damage.

vDisconnect the attached power cords, telecommunications systems,

networks, and modems before you open the device covers, unless

instructed otherwise in the installation and configuration procedures.

vConnect and disconnect cables as described below when installing,

moving, or opening covers on this product or attached devices.

To Disconnect:

1. Turn off everything (unless instructed otherwise).

2. Remove power cords from the outlet.

3. Remove signal cables from connectors.

4. Remove all cables from devices.

To Connect:

1. Turn off everything (unless instructed otherwise).

2. Attach all cables to devices.

3. Attach signal cables to the connectors.

4. Attach power cords to the outlets.

5. Turn on the devices.

(D005)

Labels

As an added precaution, safety labels are often installed directly on products or

product components to warn of potential hazards.

The actual product safety labels may differ from these sample safety labels:

Safety notices v

(L001)

DANGER

Hazardous voltage, current, or energy levels are present inside any

component that has this label attached. Do not open any cover or barrier

that contains this label.

(L003)

DANGER

Multiple power cords. The product might be equipped with multiple

power cords. To remove all hazardous voltages, disconnect all power

cords.

Caution notices

A caution notice calls attention to a situation that is potentially hazardous to

people because of some existing condition. A caution notice can be accompanied

by different symbols, as in the examples below:

If the symbol is... It means....

A hazardous electrical condition with less severity than electrical

danger.

A generally hazardous condition not represented by other safety

symbols.

A hazardous condition due to the use of a laser in the product.

Laser symbols are always accompanied by the classification of the

laser as defined by the U. S. Department of Health and Human

Services (for example, Class I, Class II, and so forth).

Attention notices

An attention notice indicates the possibility of damage to a program, device, or

system, or to data. An exclamation point symbol may accompany an attention

notice, but is not required. A sample attention notice follows:

Attention: Do not bend a fiber cable to a radius less than 5 cm (2 in.);

you can damage the cable. Tie wraps are not recommended for optical

cables because they can be easily overtightened, causing damage to the

cable.

vi IBM System Storage: N6200 Series Hardware and Service Guide

Laser safety

CAUTION:

This product contains a Class 1M laser. Do not view directly with optical

instruments. (C028)

This equipment contains Class 1 laser products, and complies with FDA radiation

Performance Standards, 21 CFR Subchapter J and the international laser safety

standard IEC 825-2.

CAUTION:

Data processing environments can contain equipment transmitting on

system links with laser modules that operate at greater than Class 1 power

levels. For this reason, never look into the end of an optical fiber cable or

open receptacle. (C027)

Attention: In the United States, use only SFP or GBIC optical transceivers that

comply with the FDA radiation performance standards, 21 CFR Subchapter J.

Internationally, use only SFP or GBIC optical transceivers that comply with IEC

standard 825–1. Optical products that do not comply with these standards may

produce light that is hazardous to the eyes.

Usage restrictions

The optical ports of the modules must be terminated with an optical connector or

with a dust plug.

Safety notices vii

Rack safety

Rack installation

DANGER

Observe the following precautions when working on or around

your IT rack system:

vHeavy equipment - personal injury or equipment damage might

result if mishandled.

vAlways lower the leveling pads on the rack cabinet.

vAlways install stabilizer brackets on the rack cabinet.

vTo avoid hazardous conditions due to uneven mechanical

loading, always install the heaviest devices in the bottom of the

rack cabinet. Always install servers and optional devices starting

from the bottom of the rack cabinet.

vRack-mounted devices are not to be used as shelves or work

spaces. Do not place objects on top of rack-mounted devices.

vEach rack cabinet might have more than one power cord. Be

sure to disconnect all power cords in the rack cabinet when

directed to disconnect power during servicing.

vConnect all devices installed in a rack cabinet to power devices

installed in the same rack cabinet. Do not plug a power cord

from a device installed in one rack cabinet into a power device

installed in a different rack cabinet.

vAn electrical outlet that is not correctly wired could place

hazardous voltage on the metal parts of the system or the

devices that attach to the system. It is the responsibility of the

customer to ensure that the outlet is correctly wired and

grounded to prevent an electrical shock.

(R001 part 1 of 2)

viii IBM System Storage: N6200 Series Hardware and Service Guide

CAUTION:

vDo not install a unit in a rack where the internal rack ambient temperatures

will exceed the manufacturer's recommended ambient temperature for all your

rack-mounted devices.

vDo not install a unit in a rack where the air flow is compromised. Ensure that

air flow is not blocked or reduced on any side, front, or back of a unit used

for air flow through the unit.

vConsideration should be given to the connection of the equipment to the

supply circuit so that overloading of the circuits does not compromise the

supply wiring or overcurrent protection. To provide the correct power

connection to a rack, refer to the rating labels located on the equipment in the

rack to determine the total power requirement of the supply circuit.

v(For sliding drawers.) Do not pull out or install any drawer or feature if the rack

stabilizer brackets are not attached to the rack. Do not pull out more than one

drawer at a time. The rack might become unstable if you pull out more than

one drawer at a time.

v(For fixed drawers) This drawer is a fixed drawer and should not be moved for

servicing unless specified by manufacturer. Attempting to move the drawer

partially or completely out of the rack may cause the rack to become unstable

or cause the drawer to fall out of the rack.

(R001 part 2 of 2)

Safety notices ix

Rack relocation (19" rack)

CAUTION:

Removing components from the upper positions in the rack cabinet improves

rack stability during relocation. Follow these general guidelines whenever you

relocate a populated rack cabinet within a room or building:

vReduce the weight of the rack cabinet by removing equipment starting at the

top of the rack cabinet. When possible, restore the rack cabinet to the

configuration of the rack cabinet as you received it. If this configuration is not

known, you must do the following:

– Remove all devices in the 32U position and above.

– Ensure that the heaviest devices are installed in the bottom of the rack

cabinet.

– Ensure that there are no empty U-levels between devices installed in the

rack cabinet below the 32U level.

– If the rack cabinet you are relocating is part of a suite of rack cabinets,

detach the rack cabinet from the suite.

– Inspect the route that you plan to take when moving the rack to eliminate

potential hazards.

– Verify that the route that you choose can support the weight of the loaded

rack cabinet. Refer to the documentation that came with your rack cabinet

for the weight of a loaded rack cabinet.

– Verify that all door openings are at least 760 x 2030 mm (30 x 80 in.).

– Ensure that all devices, shelves, drawers, doors, and cables are secure.

– Ensure that the four leveling pads are raised to their highest position.

– Ensure that there is no stabilizer bracket installed on the rack cabinet

during movement.

– Do not use a ramp inclined at more than ten degrees.

– Once the rack cabinet is in the new location, do the following:

- Lower the four leveling pads.

- Install stabilizer brackets on the rack cabinet.

- If you removed any devices from the rack cabinet, repopulate the rack

cabinet from the lowest position to the highest position.

– If a long distance relocation is required, restore the rack cabinet to the

configuration of the rack cabinet as you received it. Pack the rack cabinet in

the original packaging material, or equivalent. Also, lower the leveling

pads to raise the casters off of the pallet and bolt the rack cabinet to the

pallet.

(R002)

xIBM System Storage: N6200 Series Hardware and Service Guide

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels IBM Stockage

IBM

IBM Deskstar 16GP Manuel utilisateur

IBM

IBM Ultrastar 36Z15 Manuel utilisateur

IBM

IBM TotalStorage DS300 Manuel utilisateur

IBM

IBM ATA-100 Manuel utilisateur

IBM

IBM System Storage TS2900 Manuel utilisateur

IBM

IBM Storwize V5100 Series Manuel utilisateur

IBM

IBM Slicestor 2212A Manuel utilisateur

IBM

IBM OPTIONS TR-7 Manuel utilisateur

IBM

IBM TS4500 Manuel utilisateur

IBM

IBM N3400 Manuel

IBM

IBM SAN42B-R Manuel

IBM

IBM TS1140 Manuel utilisateur

IBM

IBM VXA-2 - Tape Drive - VXAtape Manuel utilisateur

IBM

IBM TotalStorage DS300 Instructions d'utilisation

IBM

IBM Elastic Storage System 3200 Manuel technique

IBM

IBM LTO Manuel utilisateur

IBM

IBM System Storage DS4000 Manuel technique

IBM

IBM Ultrastar 36LZX Manuel utilisateur

IBM

IBM Ultrastar 36XP Manuel utilisateur

IBM

IBM Ultrastar 36LZX Manuel utilisateur

IBM

IBM DDS Gen 5 Manuel utilisateur

IBM

IBM TotalStorage Ultrium 3580 L23 Manuel

IBM

IBM LC921 Manuel utilisateur

IBM

IBM Deskstar Deskstar 5 Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur