IBM GX7000 Series Mode d’emploi

IBM Security Network Intrusion Prevention System

GX7000 Series Power Supply Unit

Replacement Instructions



About this document

This document helps you do the following tasks:

vIdentify a failed power supply unit

vRemove the failed power supply unit and replace it with a new power supply unit

vVerify that the replacement power supply unit is working correctly

Best Practice: Replace a failed power supply unit as soon as possible.

Important: Before you proceed with these instructions, please review the IBM Systems Safety Notices

provided in the IBM Media Terms and Conditions CD that is shipped with the GX7000 Series appliance.

Identifying a failed power supply unit

There are two power supply units in the back of the GX7000 Series appliance. The power supply units

can be hot-swapped, so you can replace a single power supply unit without powering down the GX7000

Series appliance.

Understanding the power supply unit LED status

Each power supply unit contains an LED that indicates whether the unit is working as expected,

generally:

vAn LED that is lit green (solid or blinking) indicates that the unit is working as expected.

vAn LED that is lit amber or is not lit (off) indicates that the unit is not working as expected.

Understanding the fault LED status

There are also fault LEDs on the front panel of the appliance that illuminate in amber when there is a

problem with one of the power supply units:

v: The fault LED for the power supply unit that is located in the top slot of the chassis in the back

of the appliance.

v: The fault LED for the power supply unit that is located in the bottom slot of the chassis in the

back of the appliance.

Note: The fault LEDs on the front panel might vary in appearance depending on which GX7000 Series

appliance you are using.

Determining when to replace a power supply unit

Use the following table to determine the status of the power supply units and whether you must replace

one of the units.

Power supply unit LEDs

(back of appliance)

Fault LEDs

(front panel of appliance) Power supply unit status What to do next?

Solid green

A solid green LED indicates

the appliance is powered

on.

and are not lit

amber on the front panel of

the appliance.

The power supply units are

working as expected.

N/A

Blinking green

A blinking green LED

indicates the appliance is in

standby mode.

and are not lit

amber on the front panel of

the appliance.

The power supply units are

working as expected.

N/A

Amber Either or are lit

amber on the front panel of

the appliance.

The power supply unit

whose fault LED is lit

amber on the front panel of

the appliance has an error.

You must replace the failed

power supply unit.

See the next topic

“Replacing a failed power

supply unit” on page 3 for

replacement instructions.

Not lit amber or off and are not lit

amber on the front panel of

the appliance.

Does the appliance have

power?

Check to make sure the

power cord is connected

correctly to the appliance

and that the appliance is

connected to a working AC

power source.

Not lit amber or off Either or are lit

amber on the front panel of

the appliance.

Does the power supply unit

whose fault LED is lit

amber on the front panel of

the appliance have power?

Check the following to

make sure.

vThe power cord is

connected correctly to the

power supply unit and

to a working AC power

outlet.

vThe power supply unit is

seated correctly in the

appliance and locked in

place.

2Network IPS GX7000 Series: PSU Replacement Instructions

Replacing a failed power supply unit

Before you begin

When you are replacing a failed power supply unit, make sure that you do not unplug the power supply

unit that is working as this will disrupt service to the GX7000 Series appliance.

Procedure

Do the following steps to replace a failed power supply unit.

1. Unplug the power cord of the failed power supply unit.

2. Remove the power supply unit.

a. Firmly grip handle A of the failed power supply unit while pressing the orange release latch B

toward handle A, and hold the release latch in this position, as shown in Figure 1.

b. Pull the failed power supply unit from the back of the appliance.

3. When fully removed from the back of the appliance, set aside the failed power supply unit.

Attention: Make sure that the gold connectors at the rear of the power supply unit do not come into

contact with your hands or with the packing material as you unpack the replacement power supply

unit. Avoid damaging the gold connectors against the chassis as you insert the replacement power

supply unit.

4. Unpack the replacement power supply unit.

5. Carefully align the replacement power supply unit, and fully insert the power supply unit into the

chassis until you hear the release latch click in place.

6. Plug in the power cord to the replaced power supply unit.

Figure 1. Removing a power supply unit on a GX7000 Series appliance

Network IPS GX7000 Series: PSU Replacement Instructions 3

What to do next

After replacing the power supply unit, you can verify that the new power supply unit is working

correctly.

vThe power supply unit LED on the back of the appliance is green (solid or blinking).

vThe fault LED (for the power supply unit that you just replaced) on the front of the appliance is not lit.

4Network IPS GX7000 Series: PSU Replacement Instructions

U.S. Government Users Restricted Rights — Use, duplication or disclosure restricted by GSA ADP

Schedule Contract with IBM Corp.

(P) PN: 97Y0551 (2P) EC: L68316

*2PL68316*

(4L) Origin: SG

Printed in Singapore

*4LSG**P97Y0551*

Table des matières

Autres manuels IBM Alimentation

IBM

IBM Power 720 Express 8202-E4B Manuel utilisateur

IBM

IBM Power System AC922 Manuel utilisateur

IBM

IBM Power System IC922 Guide de l'utilisateur

IBM

IBM S824L Mode d’emploi

IBM

IBM CS821 Manuel utilisateur

IBM

IBM 9117-MMB Manuel utilisateur

IBM

IBM S822LC Guide de l'utilisateur

IBM

IBM Power System IC922 Manuel utilisateur

IBM

IBM 9006-12C Manuel utilisateur

IBM

IBM Power System 5105-22E Manuel utilisateur

IBM

IBM E850 Mode d’emploi

IBM

IBM 7199-92X Manuel utilisateur

IBM

IBM 5786 Manuel d'utilisation et d'entretien

IBM

IBM 9006-22C Mode d’emploi

IBM

IBM Power System 9009-41A Manuel utilisateur

IBM

IBM 9008-22L Manuel utilisateur

IBM

IBM Power System L922 Manuel utilisateur

IBM

IBM PurePower System Mode d’emploi

IBM

IBM 11000 VA LCD 5U Manuel utilisateur

IBM

IBM S822L Manuel utilisateur

IBM

IBM 8203-E4A Manuel utilisateur

IBM

IBM 9223-22H Manuel utilisateur

IBM

IBM POWER 730 Manuel utilisateur

IBM

IBM Power Systems 8005-12N Mode d’emploi

Manuels Alimentation populaires d'autres marques

Monacor

Monacor PS-12CCD Manuel utilisateur

VOLTIMA

VOLTIMA MagicBox 15 Manuel utilisateur

Agilent Technologies

Agilent Technologies 6032A Manuel utilisateur

Miller

Miller Auto Deltaweld 452 Manuel utilisateur

BCP

BCP PUOUBK Feuille d'instructions

HC 2210 Manuel utilisateur

Puls

Puls CT5.241 Manuel utilisateur

OCZ

OCZ ZX1250W Manuel utilisateur

iseg

iseg ECH 238 Manuel utilisateur

Power

Power XXL A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 6631B Manuel utilisateur

Renogy

Renogy PHOENIX 300 Manuel utilisateur

HP 6200B Manuel de service

Epson

Epson Stylus Scan 2500 Manuel d'utilisation

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuel utilisateur

Puls

Puls MiniLine ML50.100 Manuel utilisateur

Puls

Puls AS-Interface SLA4.100 Manuel utilisateur

Kenwood

Kenwood PS-60 Manuel utilisateur