IBM 37L1415 Manuel utilisateur
Serial I/O SST16P DB and RJ Adapter
37L1415 and 37L1423
Installation Guide
37L1477
560155/A
October1998
OPTIONS
by IBM
560155_A.p65 11/25/98, 6:56 PM1
IBM Serial I/O SST-16P Installation Guide 2
Figure 1. Serial I/O SST16P Adapter
Overview
IBM Serial I/O Adapters are intelligent, high-speed (up to 230.4
kbps on each port) Multiport Boards providing high performance
serial I/O solutions for PCI bus systems. All port interfaces are
standard RS-232 with full modem control and voltage surge
protection on every pin.
IBM Serial I/O Adapters appear to the system host processor as
memory. That is, they are memory mapped devices. Each Adapter is
automatically mapped into system memory at the time of device
driver installation. The device driver soft-configures all adapters
each time the system is initialized (booted). See the Software
Reference Manuals located on the CD ROM for detailed Device Driver
information.`
The IBM Serial I/O Adapter (see Figure 1 below) occupies a single
PCI slot in the host computer and provides the intelligent functions
to "off-load" the CPU serial communications processing tasks.
560155_A.p65 11/25/98, 6:56 PM2
IBM Serial I/O SST-16P Installation Guide 3
Installation
Note: Please refer to the user manual that came with your
personal computer for detailed installation instructions.
Use the following procedure to install your Serial I/O Adapter Card:
1. Set the host computer system power switch to OFF and
disconnect the power cord.
2. Locate a free PCI expansion slot.
3. Insert and secure the board firmly into the expansion slot.
4. Connect the Host SSP-16 (37L1476) cable between the SST-
16P board and the Connector Panel (see Figure 1).
5. Replace the power cord and turn the host computer system ON.
Plug and Play
Peripheral Component Interconnect (PCI) system architecture has a
design feature termed Plug and Play. This feature automatically
detects, identifies and configures the currently installed devices
each time the system is booted. Therefore, whenever an adapter
card is installed (or removed) in a PCI system, the card is recog-
nized and configured immediately upon restart.
Software Installation
Refer to the Quick Start Card that came with the CD ROM for
detailed instructions on loading the Software Driver
Connector Panels
IBM Serial I/O Connector Panels (CP) provide sixteen RS-232
interfaces. There are two types of CPs available from IBM as shown in
Figure 2. The CP-16 DB has sixteen male DTE connectors (Figure 3).
The CP-16 RJ has sixteen 10-wire female RJ-45 connectors (Figure 4).
560155_A.p65 11/25/98, 6:56 PM3
IBM Serial I/O SST-16P Installation Guide 4
Figure 4. SST-16P RJ Connector Panel Pin-outs
Connector Panels (continued)
Figure 2. SST-16P (37L1423) and SST-16P (37L1415)
Connector Panels
Figure 3. SST-16P Connector Panel Pin-outs
560155_A.p65 11/25/98, 6:56 PM4
IBM Serial I/O SST-16P Installation Guide 5
Port to Device Cabling
The following six figures show how to pin-out your own cables to go
between CP-16 Connector Panel (CP) ports and your Terminals,
Printers, Modems, etc.
DB Connector Panel to Device Cabling
Figures 5 through 7 show the pin-outs required to make a cable to go
between DB-25 ports and your Terminals, Printers, Modems, etc.
Figure 6. Cable Pin-Outs CP DB-25 to PC DB-9
Figure 5. Cable Pin-Outs for CP DB-25 to Terminal/Printer DB-25
560155_A.p65 11/25/98, 6:56 PM5
IBM Serial I/O SST-16P Installation Guide 6
DB-25 Connector Panel to Device Cabling (continued)
RJ-45 Connector Panel to Device Cabling
Figures 8 through 10 show the pin-outs required to make a cable to go
between CP16 RJ-45 CP ports and your terminals, printers, modems, etc.
Figure 7. Cable Pin-Outs for CP DB-25 to Modem DB-25
Figure 8. Cable Pin-Outs for CP-16 RJ-45 to Terminal/ Printer DB-25
560155_A.p65 11/25/98, 6:56 PM6
IBM Serial I/O SST-16P Installation Guide 7
RJ-45 Connector Panel to Device Cabling (continued)
Figure 9. Cable Pin-Outs for CP-16 RJ-45 to PC (DB-9)
Figure 10. Cable Pin-Outs for CP-16 RJ-45 to Modem DB-25
560155_A.p65 11/25/98, 6:56 PM7
IBM Serial I/O SST-16P Installation Guide 8
Help and Service Information
Before calling, please prepare for your call by following these steps:
Preparing for the Call
To assist the technical support representative, have available as much
of the following information as possible:
• Computer manufacturer and computer model.
• Options part number (Table 1).
• Options part name (Table 1).
• Serial number (if available).
• Proof of purchase (including date and place).
• Exact wording of the error message (if any)
• Description of the problem
• Hardware and software configuration information for your system
If possible, be at your computer. Your technical support representative
might want to walk you through the problem during the call.
Placing the Call to IBM
Technical support is available during the warranty period to answer
any questions about your new IBM option. Support response time will
vary depending on the number and nature of calls received.
Marketing, installation, and configuration support will be withdrawn
from the PC Company HelpCenter 90 days after the option has been
withdrawn from marketing.
If you call 90 days after the date of withdrawal or after your warranty
has expired, you might be charged a fee. Additional support is
available through the IBM PC Company automated Fax system, the
PC Company Web Page, the PC Company Electronic Bulletin Board
System and HelpWare offerings.
• The IBM web site at “http://www.pc.ibm.com
• The IBM Fax system at (800) 426-3395 or (919) 517-0011
• The IBM BBS system at (919) 517-0001
For the support telephone and support hours by country, refer to the
following table or to an optional enclosed technical support insert. If the
number is not provided in the table or insert, contact your IBM reseller
or IBM marketing representative.
keewasyad7,yadasruoh42troppuS
adanaC8737-624-008-1
ociRotreuP/setatSdetinU8737-624-008-1
560155_A.p65 11/25/98, 6:56 PM8
IBM Serial I/O SST-16P Installation Guide 9
SNOITPOMBI
traPMBI rebmuN
sretpadAO/IlaireSICP
4141L73retpadABDP8TSSO/IlaireS
5141L73retpadAJRP61TSSO/IlaireS
3241L73retpadABDP61TSSO/IlaireS
6141L73retpadAelbadnapxE821TSSO/IlaireS
7141L73eludoMtroPJR61MPO/IlaireS
8141L73eludoMtroPBD61MPO/IlaireS
1241L73ylppuSrewoP4SPO/IlaireS
2241L73ylppuSrewoPTW4SPO/IlaireS
9141L73teSrexelpitluMJR61O/IlaireS
0241L73teSrexelpitluMBD61O/IlaireS
4241L73teSrexelpitluMTWJR61O/IlaireS
5241L73teSrexelpitluMTWBD61O/IlaireS
Table 1 Options Parts Names and Numbers
Cable Options
Please refer to www.equinox.com for cabling alternatives.
560155_A.p65 11/25/98, 6:56 PM9
IBM Serial I/O SST-16P Installation Guide 10
Product Warranty
The following warranty information applies to products purchased in
the United States, Canada, and Puerto Rico. For warranty terms and
conditions for products purchased in other countries, see the enclosed
Warranty insert, or contact your IBM reseller or IBM marketing
representative. International Business Machines Corporation
Armonk, New York, 10504
Statement of Limited Warranty
The warranties provided by IBM in this Statement of Limited War-
ranty apply only to Machines you originally purchase for your use,
and not for resale, from IBM or your reseller. The term “Machine”
means an IBM machine, its features, conversions, upgrades, elements,
or accessories, or any combination of them.
Unless IBM specifies otherwise, the following warranties apply only
in the country where you acquire the Machine. If you have any
questions, contact IBM or your reseller.
Production Status
Each Machine is manufactured from new parts, or new and used parts.
In some cases, the Machine may not be new and may have been
previously installed. Regardless of the Machine’s production status,
IBM’s warranty terms apply.
The IBM Warranty for Machines
IBM warrants that each Machine
1) is free from defects in materials and workmanship and
2) conforms to IBM’s Official Published Specifications.
The warranty period for a Machine is a specified, fixed period
commencing on its Date of Installation. The date on your receipt is the
Date of Installation, unless IBM or your reseller informs you other-
wise. During the warranty period IBM or your reseller, if authorized
by IBM, will provide warranty service under the type of service
designated for the Machine and will manage and install engineering
changes that apply to the Machine.
For IBM or your reseller to provide warranty service for a feature,
conversion, or upgrade, IBM or your reseller may require that the
Machine on which it is installed be:
560155_A.p65 11/25/98, 6:56 PM10
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels IBM Matériel réseau
IBM
IBM 32R1860 - Nortel Layer 2/3 Copper GbE Switch... Manuel utilisateur
IBM
IBM J58S Manuel utilisateur
IBM
IBM 8271 F12 Manuel utilisateur
IBM
IBM 10G Network Active Bypass Manuel utilisateur
IBM
IBM 8677 - BladeCenter Rack-mountable - Power... Manuel technique
IBM
IBM 7036-P16 Manuel utilisateur
IBM
IBM Storwize V3500 Manuel utilisateur
IBM
IBM GX5008C-ROHS Mode d’emploi
IBM
IBM Ethernet Appliance J34S Manuel utilisateur
IBM
IBM 8852 - BladeCenter H Rack-mountable Manuel utilisateur
IBM
IBM Proventia Management SiteProtector SP1001 Manuel utilisateur
IBM
IBM 16/4 Token Ring PCI Special NIC Instructions d'utilisation
IBM
IBM NEXUS 5000 - OVERVIEW 19-10-2010 Manuel utilisateur
IBM
IBM DU3 2104 Manuel
IBM
IBM MDS 9124 - INTEROPERABILITY MATRIX 12-1-2010 Manuel utilisateur
IBM
IBM 8687-3RY Manuel utilisateur
IBM
IBM 8677 - BladeCenter Rack-mountable - Power... Manuel utilisateur
IBM
IBM J56S Manuel utilisateur
IBM
IBM 360 Manuel utilisateur
IBM
IBM TotalStorage 201 Fiche d'information produit
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
