i3 International Ax45RM series Manuel utilisateur
Ax45RM/65RM-series
User Manual
Before attempting to connect or operate this product, read these instructions carefully.
Save this manual for future use.
CONTENTS
1. Warnings and operation notes..................................3
2. Unpacking................................................................5
3. Dimensions & Parts Identification...........................6
4. Installation...............................................................7
5. Connecting to the SRX-Pro Server.........................16
6. Advanced Camera Setup.........................................21
7. Specifications.....................................................54
2
i3-TRNG-CAMS-Ax45RM_65RM-UM.indd Rev. 161107
Ax45RM/65RM-series User Manual
COPYRIGHT © 2016 by i3 International, Inc. All rights reserved.
No part of this manual may be reproduced or transmitted in any form or by any means,
electronic or mechanical, including but not limited to, photocopying, recording, or by
any information storage or retrieval system, without the prior written permission of the
copyright owner and the publisher.
Annexxus is a registered trademark of i3 International Inc.
Disclaimer
This quick start guide is provided as is, without warranty of any kind, expressed or
implied, including but not limited to performance, merchantability, or fitness for any
particular purpose. Neither i3 International Inc. nor its dealers or distributors shall be
liable to any person or entity with respect to any liability, loss, or damage, caused or
alleged to have been caused directly or indirectly by this information.
Furthermore, i3 International Inc. reserves the right to revise this publication, and to
make changes to the content at any time, without notice.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Address:
i3 International Inc.
780 Birchmount Road, Unit 16
Scarborough, ON M1K 5H4
Canada
Contact us:
Tech Support: 1.877.877.7241
Web Site: www.i3international.com
3Rev. 161107
i3-TRNG-CAMS-Ax45RM_65RM-UM.indd
1. Warnings and operation notes
Please read this guide carefully before you install the camera.
Keep this guide for future reference.
Thank you for purchasing an i3 Ax45RM/65RM-series IR Outdoor Dome Camera w/
Motorized Lens. If the system needs to be modified or repaired, contact a certified i3
International Dealer/Installer. When serviced by unauthorized technician, the system
warranty will be voided. Should you have any problems or questions regarding our
products, contact your local i3 International Dealer/Installer.
WARNING! To reduce the risk of fire or electric shock, do not
expose the product to rain or moisture.
Camera’s default IP address is 192.0.0.16
Camera’s default Subnet mask address is 255.255.255.0.
Default camera User Name: i3admin and default Password: i3admin
1.1 Precautions
Installation and servicing should be performed only by qualified and
experienced technicians to conform to all local codes and to maintain your
warranty.
When installing your Ax45RM/65RM camera, be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• contaminants such as dust and smoke
• strong magnetic fields
• sources of powerful electromagnetic radiation such as radios or TV transmitters
• moisture and humidity
• areas with mechanical vibrations
• fluorescent lamps or objects that reflect light
• unstable light sources as this may cause flickering
• temperatures below -40°C (-40°F) and above 50°C (122°F)
4
i3-TRNG-CAMS-Ax45RM_65RM-UM.indd Rev. 161107
1.2 Power
This camera supports AC 24V and PoE (IEEE 802.3af Class 3). Max. load of 26W on AC
24V, 20W on PoE+ and 11W on PoE.
Incorrect voltage may cause irreparable damage to the video camera and will
effectively void the camera warranty. For PoE power, insert the RJ45 cable into
the RJ45 jack on the camera’s cable. Connect the other end of the RJ45 cable to
a compatible PoE switch/hub/router. Use RJ45 waterproof connector for outdoor
installations (not included).
1.3 Cleaning
• For maximum optical clarity, the camera or lens must remain clean. Use a soft, dry
cloth to remove finger prints and dust from the dome cover.
• Use a blower to remove dust from the lens.
• Clean the body with a soft, dry cloth. If it is very dirty, use a cloth dampened with a
small quantity of neutral detergent, then wipe dry.
• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may
damage the surface finish.
1.4 Servicing
To avoid electrical shock and to preserve the product warranty, DO NOT disassemble
the camera. Refer servicing to qualified personnel only.
1.5 Routine Maintenance
• The dome bubble is an optical part. Use a soft and dry cloth to remove any
fingerprints and dust.
• Clean the camera housing with a soft and dry cloth. For more stubborn marks, use
a cloth dampened with a small quantity of neutral detergent, then wipe dry.
• CAUTION: Do not use volatile solvents such as alcohol, benzene or
thinners, as they may damage the surface finish.
Please Note: Scan the QR code below or visit www.i3international.com to view and download the full User
Manual for this camera. Also available for download is the AnnexxusConfigurationTool or ACT program
used to locate and configure your cameras with your SRX-Pro software. This program is already installed
in SRX-Pro v3.3.3.69 and higher. Please contact our Technical Support team if you have any questions or
concerns regarding camera installation or you require software services or support. Technical support can
be reached by email at:
QR Code to Complete
User Manual / ACT
5Rev. 161107
i3-TRNG-CAMS-Ax45RM_65RM-UM.indd
2. Unpacking
Ensure that the items received match those listed on the order form and the packing
slip. In addition to this manual and a fully assembled camera, the dome camera
packing box includes:
1. Surface Mount template x1.
2. Rubber gasket x1. Use in all outdoor surface installations in combination with
surface Mount Template.
3. Security torx bit x1.
4. Flush Mount template x1.
5. Round Head Screw (Tapping Type) with O-ring x4.
6. Plastic Anchor x4.
7. 3-ft netowrk cable x1.
8. Long Machine Type screws x3 for flush mounting with back box installations.
9. Standard Rj45 connector x2.
*Note: Based on installation location and surface type, supplied screws and anchors
may not be adequate. Mounting hardware is site-specific and may need to be supplied
by the installer.
2.1 Accessories (not to scale)
Lens Direction
GUIDE PATTERN
GUIDE PATTERN
CAMERA OUTLINE
CUT LINE
1234
56 7 8
9
6
i3-TRNG-CAMS-Ax45RM_65RM-UM.indd Rev. 161107
12
13
14
15
15
15
16
16
3. Dimensions & Parts Identification
This dome camera is suitable for both indoor and outdoor installation in commercial
and residential environment. With 3-axis mount support, it provides flexible installation
on a ceiling or wall, even on an angle. The dome camera is a fully integrated enclosure
with a back box, camera and lens.
910 11
147 mm (5¾”)
68 mm (2.67”)
94 mm (3.7”)
158 mm (6¼”)
63 mm (2.5”)
84 mm (3.3”)
63 mm (2.5”)
1
2
5
3
4
6
7
8
7Rev. 161107
i3-TRNG-CAMS-Ax45RM_65RM-UM.indd
1. Back box. Camera’s back box comes with six (6) 90% pre-drilled hole dimples
with built-in O-ring. For surface mounting, complete drilling a minimum of two (2)
holes.
2. Camera module / second housing
3. Tilt bracket with locking screw
4. Inner liner / Shroud. Inner liner is attached to the camera module but can be
partially detached for easier lens adjustment.
5. IR board
6. Screws securing the dome bubble housing to camera module (x3, silver)
7. Dome bubble housing / Dome cover
8. Lexan bubble
9. 3/4” Top conduit hole. During installation, sealant must be used to maintain the
IP67 status.
10. 3/4” Side conduit hole. During installation, sealant must be used to maintain the
IP67 status.
11. Six (6) 90% pre-drilled hole dimples with built-in O-ring.
12. Reset/Default pin-hole button. Press for 1 second to reboot the camera. Press for
6 seconds to restore camera settings to factory defaults.
13. microSD Card slot for on-camera edge video storage. (microSD cards up to 64GB
supported, not supplied)
14. Mini USB port. Manufacturer use
only
.
15. Screws attaching camera module to the back box (x3, silver)
16. Screws to engage locking arms (x2, black)
4. Installation
Ax45RM/65RM camera series can be flush-, wall-, surface-, or T-bar ceiling mounted
without additional mounting accessories/brackets.
Start by marking out and preparing the mounting surface, then attach the supplied
mounting template to the mounting surface. Use the appropriate brackets and
equipment to mount the camera. Use supplied rubber gasket in all outdoor surface
installations to provide the seal between the mounting surface and the camera base.
Depending on the type of installation, additional mounting accessories may need to be
purchased.
After installing the camera, your network camera must be accessible from your local
network (LAN).
Optional Mounting Accessories:
• DB60 (Goose Neck Wall Bracket 3/4” NTP). Together with the optional DB60CPM
bracket, DB60 goose neck bracket has the capability of being corner or pole-
mounted.
• DB60CPM (Corner / Pole Mount bracket for DB60)
8
i3-TRNG-CAMS-Ax45RM_65RM-UM.indd Rev. 161107
4.1 Disassembling the Camera
Before mounting and adjusting the camera, follow
these steps to disassemble the camera.
1. Use the provided security Torx bit to loosen
three silver screws securing the dome
bubble housing to camera module (#6). Do
not completely remove the screws from the
dome bubble. Set the dome bubble aside.
2. Use Phillips screwdriver to loosen three
silver screws attaching camera to the
back box (#15)
3. Remove camera’s back box and set aside.
4.2 I/O Connectors (Reserved for future use
Once the camera’s back box has been
removed, Ax45RM/Ax65RM input/output
connectors will be revealed on the
camera’s module, including RJ45 Ethernet/
PoE connector, Audio and Alarm connectors
and AC24V power port.
9Rev. 161107
i3-TRNG-CAMS-Ax45RM_65RM-UM.indd
1. I/O connectors reserved for future use.
2. AC 24V Port. Connect AC 24V power supply.
3. RJ45 Ethernet Connector / PoE. Connect RJ45 network cable for Ethernet/Internet
connectivity. PoE (Power over Ethernet) is supported.
Caution: Do not apply power until the camera is properly and securely mounted.
4. Orange LED. Flashing orange LED indicates data transmission between camera
and the Internet.
5. Green LED. Solid green LED indicates a current live connection.
Reserved Reserved
GND GND AO AI
GNDCOM
4.3 3-Axis lens position adjustment
Pan Adjustment
Rotate the lens base (max 354°) until satisfied with the field of view.
Note: Over-rotation past 354° will cause internal cables to become damaged,
disconnected, or twisted.
Horizontal Rotation
Firmly grasp the camera lens assembly and rotate counter-clockwise / clockwise (max
354°) until satisfied with the field of view.
Note: Over-rotation past 354° will cause internal cables to become damaged,
disconnected, or twisted.
Tilt Adjustment
Tilt the camera lens until satisfied with the field of view.
Once the desired view has been achieved, replace the camera liner until it snaps into
place.
10°~90°
±177°
Pan Adjustment
Horizontal Rotation
Tilt Adjustment
±177°
123
4 5 Reserved Reserved
10
i3-TRNG-CAMS-Ax45RM_65RM-UM.indd Rev. 161107
Prepare the Mounting Surface:
1. Use the Flush Mounting Template to cut a
hole in the mounting surface.
Disassemble the Camera:
2. Disassemble the camera by removing the
dome bubble. Use the provided security Torx
bit to loosen three silver screws securing the
dome bubble to the camera’s mounting base.
4.4 Flush Mounting w/Locking Arms
Use this installation method for indoor installations only. This method is suitable for
drywall and T-bar installations only. It is possible to flush mount the camera and use
the back box. The Long Machine Type screws provided are used to secure the camera
to the back box through ceiling.
Important. Please Read:
• It is the installer’s responsibility to ensure that the mounting surface is
suitable for the chosen installation method.
• Based on installation location and surface type, supplied screws and
anchors may not be adequate.
• Mounting hardware is site-specific and may need to be supplied by the
installer.
GUIDE PATTERN
CAMERA OUTLINE
CUT LINE
Do not completely remove the screws from the bubble. Lift the dome bubble off
and set aside.
3. Loosen three silver screws attaching camera to the back box. Remove camera’s
back box and set aside. It will not be used in this type of installation.
Back box
not in use
for this
installation
Autres manuels pour Ax45RM series
3
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels i3 International Caméra de sécurité
i3 International
i3 International i3F416U Manuel utilisateur
i3 International
i3 International Ax65W Manuel utilisateur
i3 International
i3 International Am42 Series Manuel utilisateur
i3 International
i3 International Ax47R series Manuel utilisateur
i3 International
i3 International M79 Manuel utilisateur
i3 International
i3 International Di721 Manuel utilisateur
i3 International
i3 International Am52RM Manuel utilisateur
i3 International
i3 International Ax85 Manuel utilisateur
i3 International
i3 International Ax41C1M Manuel utilisateur
i3 International
i3 International i3-B731 Manuel utilisateur
i3 International
i3 International Ax32VD14 Manuel utilisateur
i3 International
i3 International Ax63C Instructions d'utilisation et d'entretien
i3 International
i3 International Ax61 series Manuel utilisateur
i3 International
i3 International i3B261 Manuel utilisateur
i3 International
i3 International Ax61 series Instructions d'utilisation et d'entretien
i3 International
i3 International ANNEXXUS Ax41V1MVR Manuel utilisateur
i3 International
i3 International AM42R Manuel utilisateur
i3 International
i3 International A 47DC Series Manuel utilisateur
i3 International
i3 International C-AX401D1M Manuel utilisateur
i3 International
i3 International A 65W Series Manuel utilisateur
