Hytronik HIR21 Manuel utilisateur
Hytronik PIR motion sensor
347
Stand-by power
EMC standard (EMC)
Safety standard (LVD)
Resistive
EN55015, EN61000
Semko, CB, CE , EMC, LVD, RCM
1600W
EN60669-1, EN60669-2-1
Model No. HIR21
220~240VAC 50/60Hz
Mains voltage
Load ratings:
<0.5W
Input Characteristics
Safety and EMC
800W
Capacitive
Sensor Data
HIR21
Operation temperature
Ta: -20
O
C ~ +50
O
C
Environment
IP20
IP rating
Model No.
360O
5m (maximum)
PIR detectionSensor principle
Detection range
Detection angle
Mounting height
(O x H) 10m x 3m
30sWarming-up
HIR21
1-10V Dimming with Remote Control
Flush Mount PIR Motion Sensor
Technical Data
(1) Sensor inset
(2) Lens pluggable
(3) Protection cover (covers the
high-voltage terminals).
(4) Ceiling (drill hole Ø70mm).
Infrared receiver
Photocell
LED indicator
PIR
Rotary switch preset
1
3
4
2
70mm 64.7
68.1
73.3
56
Ø85
PIR
Mechanical Structure
IP20
www.hytronik.com
Note: the blinds are optional, they may be inserted
behind the lens for focussing the detection range.
Blind
A
Blind
B
Hytronik PIR motion sensor
348
Functions and Features
Intelligent Photocell (daylight detection prior to motion detection)
2
The built-in photocell will also automatically turn off the light when the ambient natural light exceeds the programmed lux level for
stays at
dimmed level during absence.
switches on the light automatically when
presence is detected.
does not switch on when presence is
detected.
The sensor switches off the light when
presence.
Manual Override
3
* Short Push (<1s): on/off function;
On →Off: the light turns off immediately and cannot be triggered ON by motion until the expiration of pre-set hold-time. After this
period, the sensor goes back to normal sensor mode.
Off →On: the light turns on and goes to sensor mode, no matter if ambient Lux level exceeds the daylight threshold or not.
* Long Push (>1s): adjust the hold-time brightness level between10% and 100%.
Note: if end-user do not want this manual override function, just leave the “push” terminal unconnected to any wire.
With the help of push-switch, this sensor can be over-ridden by the end-user to manually switch on/off the light, or adjust the
:
Semi-auto Mode (Absence Detection)
4
have a
sensor to switch on the light automatically, for example, when people just quickly pass-by, there is no need to have the light on. The
solution is to apply this “absence detector”: motion sensor is employed, but only activated on the manual press of the push-switch, the
light keeps being ON in the presence, and dims down in the absence, then switches off in the long absence.
Note: end-user can choose either function or function for application. Default function is manual override.
3 4
Tri-level Control (Corridor Function)
1
Hytronik builds this function inside the motion sensor to achieve tri-level control, for some areas which require a light change notice
ds of
selectable waiting time: motion hold-time and stand-by period; Selectable daylight threshold and freedom of detection area.
www.hytronik.com
Hytronik PIR motion sensor
349
Press the buttons to select light output at 80% (at initial 10,000 hours) or 100%.
Note: “Sensor off” and “Twilight” functions are disabled.
zero-cross point
Alternating current
Zero-cross Relay Operation
Designed in the software, sensor switches on/off the
load right at the zero-cross point, to ensure that the
in-rush current is minimised, enabling the maximum
lifetime of the relay.
5
Double L N terminal makes it easy for wire loop-in and loop-out, and saves the cost of terminal block and assembly time.
Loop-in and Loop-out Terminal
6
Settings (Remote Control HRC-11)
HRC-11
Press button “RESET”, all settings go back to rotary switch settings.
Reset Settings
Permanent ON/OFF function
Press button “ON/OFF” to select permanent ON or permanent OFF mode.
* Press button “AUTO”, “RESET” to quit this mode.
AUTO mode
Press button “AUTO” to initiate automatic mode. The sensor starts working and all
settings remain as before the light is switched ON/OFF.
manually turned on by pressing the push-switch, and goes off automatically in this
mode. (Absence detection mode)
ON/
OFF
SEMI-AUTO mode
Power output
Press the buttons to adjust the light brightness during hold-time.
Brightness +/-
www.hytronik.com
&
A
Press button “Shift”, the LED on the top left corner is on to indicate mode selection.
All values / settings in RED are valid for 20 seconds.
Shift Button
The mode will change to AUTO Mode after power failure.
Hytronik PIR motion sensor
350
Scene program - 1-key commissioning
Detection range
Press buttons in zone “Detection range” to set detection range at 100% / 75% / 50% / 10%.
Press buttons in zone “ Daylight threshold” to set daylight sensor at 2Lux/ 10Lux / 50Lux / 100Lux / 300Lux / 500Lux / Disable.
Daylight threshold
2. Press button “Ambient”, the surrounding lux level is sampled and set as the new daylight threshold.
Ambient daylight threshold
Hold-time
Press buttons in zone “hold-time” to set the hold-time at 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min.
2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.
*To exit from Test mode, press button “RESET” or any button in “Hold-time”.
1. Press button “Start” to program.
2. Select the buttons in “Detection range”, “Daylight threshold”, “Hold-time”, “Stand-by time”, “Stand-by dimming level” to set all
parameters.
3. Press button “Memory” to save all the settings programmed in the remote control.
4. Press button “Apply” to set the settings to each sensor unit(s).
For example, to set detection range 100%, daylight threshold Disable, hold-time 5min, stand-by time +∞, stand-by dimming level 30%, the steps should be:
Press button “Start”, button ”100%”, “Disable”, “Shift”, “5min”, “Shift”, “+∞”, “30%”, “Memory”. By pointing to the sensor unit(s) and pressing “Apply”, all
settings are passed on the sensor(s).
Dual tech & RF mode
Stand-by dimming level
Stand-by time (corridor function)
Press buttons in zone “stand-by time” to set the stand-by period at 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞.
at the stand-by dimming level
when no presence after motion hold-time.
Press the button in zone “stand-by dimming level” to set the stand-by dimming level at 10% / 20% / 30% / 50%.
All buttons are disabled.
www.hytronik.com
All buttons in this zone are disabled.
Hytronik PIR motion sensor
351
A rotary switch is built inside the sensor for scene
selection / fast programming. Total 16 channels
are available:
Rotary switch preset
Rotary Switch Preset
Note: settings can also be changed by remote control
HRC-11. The last action controls.
0 5s100% Disable
nim11 100% 2Lux
nim52 100% 10Lux
nim53 100% 30Lux
nim54 100% 10Lux
nim55 100% 30Lux
nim56 100% Disable
nim017 100% 2Lux
nim018 100% 10Lux
nim019 100% 30Lux
nim01A 100% Disable
nim01xBuL03%57
C 10min xuL01%05
nim03D 100% 50Lux
E30min100% Disable
F5s100%
10%
10%
10%
10%
Disable
10%
30%
10%
10%
10%
30%
10%
10%
10%
30%
10%2Lux
10s
5min
10min
30min
0s
+∞
+∞
10min
30min
+∞
+∞
+∞
+∞
+∞
+∞
10s
Detection
range
Channel Hold-time Stand-by
time
Stand-by
dim level
Daylight
sensor
Wiring Diagram
LED Driver
HIR21
L
N
Detection Pattern
1-10V
+
-
P
L
N
1-10V
+
-
L’ N N L LED+
LED -
www.hytronik.com
2
2
Tangential movement 10m
Radial movement 8m
3m
7
Tangential movement 10m
4m
4m
4m
4
3m
3m
Tangential movement 5m
Radial movement 4m
1
AB
Table des matières
Autres manuels Hytronik Capteur de sécurité
Hytronik
Hytronik Dual Sense HIM17 Manuel utilisateur
Hytronik
Hytronik HCD405/BT Guide rapide
Hytronik
Hytronik Dual Sense HIM14 Manuel utilisateur
Hytronik
Hytronik HIR32 Manuel utilisateur
Hytronik
Hytronik HBHC25 Guide rapide
Hytronik
Hytronik HMW31 Guide rapide
Hytronik
Hytronik HIR21 Manuel utilisateur
Hytronik
Hytronik HIR22 Manuel utilisateur
Hytronik
Hytronik HIM38/RF Guide rapide
Hytronik
Hytronik HIM32 Manuel utilisateur
Hytronik
Hytronik HIM54 Manuel utilisateur
Hytronik
Hytronik HCD038+HIR17 Guide rapide
Hytronik
Hytronik HIR24 Guide rapide
Hytronik
Hytronik HC034RF Guide rapide
Hytronik
Hytronik HMW25 Manuel utilisateur
Hytronik
Hytronik HIM84 Guide rapide
Hytronik
Hytronik HMW39/RF Manuel utilisateur
Hytronik
Hytronik HCD438 Manuel utilisateur
Hytronik
Hytronik HMW28/PRO Manuel utilisateur
Hytronik
Hytronik HIM31 Manuel utilisateur
