Hypertherm HD4070 PC-104 Manuel de référence

HD4070 PC-104 Upgrade

HyDefinition HD4070

Field Service Bulletin

805710 – Revision 2 – May, 2008

HD4070 PC-104 UPGRADE

Field Service Bulletin 1

Introduction

Purpose

This field service bulletin describes the steps necessary to replace the 041664 PC-104 stack with a 141023 PC-104

stack.

Kit 229169 contents

Part number Description Qty

PC-104 Stack, consisting of:

041990 Board 1: HD4070 CPU 1

141021 Board 2: HD4070 IDE Flash with HD4070 Firmware 1

042359 Memory Card:CompactFlash with HD4070 Firmware 1

041622 Board 3: HD4070 Dual Serial 1

041623 Board 4: HD4070 48ChanDigital I/O 1

042357 IC: NEC uPD71055C Parallel Interface 2

041623 Board 5: HD4070 48ChanDigital I/O 1

042357 IC: NEC uPD71055C Parallel Interface 2

041624 Board 6: HD4070 Anlg/Digital 1

041687 Board 7: PC-104 Test 1

229169 Cable: PC-104 Upgrade Power 1

123469 Ribbon Cable: 26/C 20” (B6J1) 1

123470 Ribbon Cable: 50/C 24” (B5J1) 1

123471 Ribbon Cable: 50/C 24” (B5J4) 1

123472 Ribbon Cable: 20/C 21” (B3J1) 1

123473 Ribbon Cable: 50/C 22” (B4J4) 1

123474 Ribbon Cable: 50/C 18” (B1J2) 1

123475 Ribbon Cable: 50/C 31” (B4J1) 1

123490 Ribbon Cable: 34/C (B1J3 Floppy) 1

123491 Ribbon Cable: 40/C 25” (B1J4-B2J2 IDE) 1

108114 Hardware: M3x15 M/F Standoffs 32

805710 FSB:HD4070 PC-104 Replacement Kit 1

DANGER

ELECTRIC SHOCK CAN KILL

Disconnect electrical power before performing any maintenance.

All work that requires the removal of the power supply cover must be

performed by a qualified technician.

See the safety Section of the system Manual for more safety precautions.

HD4070 PC-104 UPGRADE

2Field Service Bulletin

DANGER

ELECTRIC SHOCK CAN KILL

Turn off all electrical power before removing the power supply cover. Press the power

supply OFF (0) pushbutton switch and set the line disconnect switch to OFF. In the

U.S., use a “lock-out and tag-out” procedure until the service or maintenance is

complete. In other countries, follow appropriate local or national safety procedures.

Remove the old PC-104 stack and cables (041664)

Note: the existing ribbon cables should be removed with the old PC-104 stack. The new PC-104 stack

has new cables attached to it when shipped.

1. Turn OFF main power.

2. Remove the cables that lead to the PC-104 stack from the breakout board and the floppy drive in the following order

(see figure 1). The power source cable is removed at the PC-104 stack (B1, J25). The connector on the end of the

power cable is designated as P50.

a. J5 on the Breakout Board (Analog/Digital I/O ribbon cable to B6, J1)

b. J6 on the breakout board (Digital I/O ribbon cable to B5, J1)

c. J8 on the breakout board (Digital I/O ribbon cable to B5, J4)

d. J15 on the breakout board (Digital I/O ribbon cable to B4, J1)

e. J11 on the breakout board (Digital I/O ribbon cable to B4, J4)

f. J10 on the breakout board (Serial ribbon cable to B3, J1)

g. J13 on the breakout board (I/O ribbon cable to B1, J9)

h. J1 on the Floppy Drive (I/O ribbon cable to B1, J5)

i. B1, J25 (PC-104 power cable to the DC Power Supply). The connector on the end of the power cable is

designated as P50.

The following items are for reference. No actions are required:

j. B6, J3 (No cable connection)

k. B2, J2 (IDE ribbon cable to B1, J6)

l. B1, J4 (IDE ribbon cable to B2, J2)

3. Remove the four (4) screws that secure B1 to the Control Box. Keep the screws for installing the replacement

PC-104 stack (141023).

4. Remove the old PC-104 stack (041664) and cables. Remove the compact flash card from the old PC-104 stack,

carefully package it, and ship it back to Hypertherm for a return credit.

HD4070 PC-104 UPGRADE

Field Service Bulletin 3

Figure 1 – Breakout board

Figure 1.1 – Floppy disk drive

J15

J11

J13

J10

Figure 1.2 – Power cable

B1, J25

HD4070 PC-104 UPGRADE

4Field Service Bulletin

2. Reinstall the four (4) screws on B1 that were removed earlier.

3. Place the PC-104 Power Cable (229169) so that the PCB is near the access hole next to the DC Power Supply

(041626). Clean the area where the cable tie will be installed, remove the adhesive backing from the cable tie base

under the PCB, and secure the PCB to the bottom of the Control Box (see Figure 3).

Access hole

Power cable PCB

Figure 3 Figure 3.1

DC power supply

CPU heatsink on B1

Figure 2

Install the new PC-104 stack and cable (141023)

1. Place the new PC-104 stack (141023) into the Control Box, and orient it so that the CPU heatsink on B1 is on the

same side as the DC Power Supplies (See figure 2).

4. Connect the P50 cable end to J1 on the power cable PCB.

Note: PC-104 power cable connections:

P50A cable end is connected to B1, J13 on the PC-104 stack.

P50B cable end is connected to J2 on the power cable PCB.

P50 cable end from the power source connects to J1 on the power cable PCB.

P50 cable end

HD4070 PC-104 UPGRADE

Field Service Bulletin 5

LEDN1

B6-J3

B2-J2

B1-J13

B6-J1

B5-J4

B4-J4

B1-J5

B1-J9

B5-J1

B4-J1

B3-J1

B1-J6

Figure 4 – 141023 PC-104 stack

4. Reinstall the PC-104 ribbon cable connectors to the breakout board and the floppy drive in the following order (see

Figure 1 and Figure 4).

a. J5 on the Breakout Board (Analog/Digital I/O ribbon cable to B6, J1)

b. J6 on the breakout board (Digital I/O ribbon cable to B5, J1)

c. J8 on the breakout board (Digital I/O ribbon cable to B5, J4)

d. J15 on the breakout board (Digital I/O ribbon cable to B4, J1)

e. J11 on the breakout board (Digital I/O ribbon cable to B4, J4)

f. J10 on the breakout board (Serial ribbon cable to B3, J1)

g. J13 on the breakout board (I/O ribbon cable to B1, J9)

h. J1 on the Floppy Drive (I/O ribbon cable to B1, J5)

The following items are for reference. No actions are required:

i. B6, J3 (No cable connection)

j. B2, J2 (IDE ribbon cable to B1, J6). Comes installed from the factory.

k. B1, J4 (IDE ribbon cable to B2, J2). Comes installed from the factory.

Hypertherm, Inc.

Hanover, NH 03755 USA

603-643-3441 Tel

Hypertherm (S) Pte Ltd.

417847, Republic of Singapore

65 6 841 2489 Tel

Hypertherm (Shanghai)

Trading Co., Ltd.

PR China 200052

86-21 5258 3330 /1 Tel

Hypertherm Europe B.V.

4704 SE Roosendaal, Nederland

31 165 596907 Tel

HYPERTHERM BRASIL LTDA.

Guarulhos, SP - Brasil

55 11 6409 2636 Tel

www.hypertherm.com

Hypertherm, HD4070, and HyDefinition are trademarks of Hypertherm, Inc. and may be registered in the United States and/or other countries.

Table des matières

Autres manuels Hypertherm Coupeur

Hypertherm

Hypertherm Powermax30 AIR Manuel utilisateur

Hypertherm

Hypertherm HyPerformance HPR400XD Manuel utilisateur

Hypertherm

Hypertherm HyPerformance HPR400XD Manuel utilisateur

Hypertherm

Hypertherm PMX1000 Manuel de référence

Hypertherm

Hypertherm Powermax30 AIR Manuel utilisateur

Hypertherm

Hypertherm HyPerformance Plasma HPR260 Manuel utilisateur

Hypertherm

Hypertherm HyDefinition HD4070 Manuel utilisateur

Hypertherm

Hypertherm HyPerformance Plasma HPR800XD Manuel utilisateur

Hypertherm

Hypertherm powermax 190c Manuel utilisateur

Hypertherm

Hypertherm HT4001 Manuel utilisateur

Hypertherm

Hypertherm ArcGlide Torch Height Control Manuel utilisateur

Hypertherm

Hypertherm MAX200 Manuel utilisateur

Hypertherm

Hypertherm Command THC Manuel utilisateur

Hypertherm

Hypertherm HyDefinition HD3070 Manuel utilisateur

Hypertherm

Hypertherm HT4400 Manuel utilisateur

Hypertherm

Hypertherm Powermax45 XP Manuel utilisateur

Hypertherm

Hypertherm MAX200 Manuel utilisateur

Hypertherm

Hypertherm HyPerformance Plasma HPR400 Manuel utilisateur

Hypertherm

Hypertherm POWERMAX 800 Manuel utilisateur

Manuels Coupeur populaires d'autres marques

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manuel utilisateur

Makita

Makita DCS552 Manuel utilisateur

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manuel utilisateur

Makita

Makita 4112HS Manuel utilisateur

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manuel utilisateur

Hitachi

Hitachi CM 4SB2 Guide de dépannage

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manuel utilisateur

GCC Technologies

GCC Technologies AFJ-24S Manuel utilisateur

DeWalt

DeWalt XR LI-ION DCS350N Manuel utilisateur

Baudat

Baudat ES1 Manuel utilisateur

Mafell

Mafell ZAF 200 Mode d’emploi

Makita

Makita 4100NH Manuel utilisateur

Formax

Formax FD 574 Manuel utilisateur

EINHELL

EINHELL TE-MA 1500 Manuel utilisateur

Husqvarna

Husqvarna Cut-n-Break K 760 Manuel utilisateur

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manuel utilisateur

TRI tool

TRI tool 301A Manuel utilisateur

Roller

Roller King 1 1/4 Manuel utilisateur