Hyco AP25LM Mode d’emploi
Installation & Operation
Issue 1
electric combination water heater
HYCO
These tting and User Instructions refer to the following models:
AP25LM AP50LM AP75LM AP100LM
The HYCO Apollo series is a range of white enamelled cistern fed rectangular water storage
heaters. All HYCO Apollo units can be connected directly to the cold water main and if required,
can supply more than one outlet without the need for special taps.
WARNING!
-The appliance is not to be used by children or persons with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction.
-Children should be supervised and not allowed to play with the appliance.
-Maximum water pressure 690kPa
THESE INSTRUCTIONS SHOULD BE CAREFULLY READ AND UNDERSTOOD BEFORE
INSTALLATION BEGINS. IT WOULD BE DANGEROUS TO PROCEED IF ANY PART IS
UNCLEAR OR IF THE REQUIREMENTS CANNOT BE FULLY MET.
PLEASE LEAVE THESE INSTRUCTIONS WITH THE USER AFTER INSTALLATION.
INSTALLATION
WALL MOUNTING (refer to diagram A).
The unit is designed to be wall mounted and must be tted at least one metre above the
highest draw-off point thus ensuring a good ow. It is important that sufcient clearance is
allowed to ensure access to the ball valve assembly.
The wall xing points will accept 8mm bolts which should not be less than 50mm in length.
ALWAYS ENSURE THAT THE WALL IS SUFFICIENTLY STRONG TO CARRY THE WEIGHT
OF THE UNIT WHEN IT IS FULL OF WATER.
PIPEWORK CONNECTIONS (refer to Diagram B).
The installation must conform to all local authority byelaws. The cold water supply and warning
pipe (overow) assembly can be connected to either side of the unit. The respective apertures
are pre-formed in the outer case and these should be used as guides for cutting through the
cold water tank. A 22mm hole is required for the inlet and a 27mm hole for the warning pipe.
An isolating valve must be tted to the cold water mains supply to allow for servicing.
FITTING TO THE COLD WATER TANK (refer to Diagram C).
The HYCO Apollo series of water heaters are supplied with all the components that are required
to comply with the WRC bylaw 30. The arrangement of these should conform to Diagram C.
The lter and breather assembly is a push snap-t connection and should be tted to the lid in
the aperture provided.
The warning pipe assembly (overow) has three components. The threaded elbow (tank
connector) is inserted through the hole that has been cut, and tightened with the nut and
sealing washer on the inside of the tank.
The 90o bend internal “dip tube” is pushed rmly into the connector facing downwards. The
warning pipe (overow) screen is located securley into the downwards external connection of
the connector.
The ball valve assembly is tted as required, adjusting the oat to ensure that the water level
in the tank does not exceed the water level line.
NOTE: after installation, replace lid and secure with the retaining screw supplied.
ELECTRICAL CONNECTION
The Installation should be carried out by a suitably qualied person in accordance with BS 7671
(IEE) wiring regulations.
A double pole isolation switch having a contact separation of greater than 3mm should be tted
to allow for servicing.
IMPORTANT: The unit MUST be full of water before switching on the electricity supply.
The HYCO Apollo water heaters are all tted with a 3kW heating element. The heating element
is located at the base of the unit. The heating element incorporates dual thermostats that are
linked to act as a control thermostat with an over-temperature safety cut-out. The thermostats
are factory set to 50oC for the control thermostat and 70oC for the cut-out thermostat.
The control thermostat should NOT exceed 60oC and the 20oC differential between the control
and cut-out thermostat MUST be maintained.
The supply cable should be securely clamped before replacing the heating unit’s own cover AND
as it passes through the gland in the element housing cover.
If during normal service, the cut-out thermostat operates rst establish the reason for
operation. Possibly a wrongly set control thermostat. Switch off the electricity supply before
removing the element housing cover. Correct the problem and then press the button to reset
the cut-out thermostat. Replace the heating unit cover and the element housing cover before
switching on the electricity supply.
SCHEMATIC WIRING DIAGRAM
OPERATION
The cold water supply to the integral cistern is controlled by the ball valve. when one or more
hot taps are opened the hot water drawn from the unit is replaced from the contents of the cold
water cistern that is relled automatically.
COMMISSIONING
Before making the electrical connection it is recommended that the unit is lled and checked
for leaks. Apart from the plumbing connections, the element or drain may have been loosened
in transit and require tightening,
SAFETY WARNING
The unit MUST NOT be used if it is suspected of being frozen. If water caeses to ow switch off
electricity supply immediatley at the isolating switch. If the unit is to be serviced or drained
disconnect the electricity supply before commencing the operation.
Goods are guaranteed for one year against faulty design, materials or workmanship having
properly installed and operated in accordance with these instructions. The Company has the
option to replace or repair an entire product or component. The Company shall not for any
liable for any consequential loss or damage howsoever caused. It shall be the duty of the
customer to insure against such consequential loss or damage.
The guarantee does not extend to the consequences of limescale deposits, corrosion or frost
damage which the manufacturer has no control and for which the user is advised to take
appropriate precautions. This guarantee does not affect the statutory rights of the consumer.
Product
Ref:
Capacity Dimensions Weight (Kg)
Hot Cold A B C D E F Empty Full
AP25LM 25 8 705 470 735 210 670 320 21 54
AP50LM 50 24 750 600 780 320 715 450 31 108
AP75LM 75 24 925 600 950 320 890 450 38 135
AP100LM 100 24 1080 600 1110 320 1045 450 40 166
Hyco Manufacturing Ltd.
Normandy Court, Express Way
Castleford, WF10 5NR
Tel: 01924 225200 Fax: 01924 225210
HYCO
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Hyco Chauffe-eau
Hyco
Hyco IN95 Manuel utilisateur
Hyco
Hyco SF10K Manuel utilisateur
Hyco
Hyco powerflow series Manuel utilisateur
Hyco
Hyco Speedflow SF10SS Fiche technique
Hyco
Hyco Ara IN30 Fiche technique
Hyco
Hyco Handyflow HF10VC Manuel utilisateur
Hyco
Hyco ULTRAWASH 3.0kW Mode d’emploi
Hyco
Hyco IN88 Manuel utilisateur
Hyco
Hyco Aquila IN96T Fiche technique
Hyco
Hyco Handyflow Undersink HF05MVC Manuel utilisateur
Hyco
Hyco Speedflow SF10L Manuel utilisateur
Hyco
Hyco SF05K Fiche technique
Hyco
Hyco HF05VC Manuel utilisateur
Hyco
Hyco Rho Manuel utilisateur
Hyco
Hyco RHO IN44T Manuel utilisateur
Hyco
Hyco MBS6 Manuel utilisateur
Hyco
Hyco Handyflow HF05LQ Manuel utilisateur
Hyco
Hyco Rho IN44 Fiche technique
Hyco
Hyco Handyflow HF05L Manuel utilisateur
Hyco
Hyco Powerflow Manuel utilisateur
Manuels Chauffe-eau populaires d'autres marques
Kenmore
Kenmore 153.582400 Manuel utilisateur
Applimo
Applimo Edel AIR Manuel utilisateur
STIEBEL ELTRON
STIEBEL ELTRON Eltronom SHU 5 S Manuel utilisateur
clage
clage E-Mini Series Manuel utilisateur
Toyotomi
Toyotomi Oil Miser OM-180 Manuel utilisateur
Bradford White
Bradford White EF Series Manuel utilisateur
