Hussmann IMPACT RL Manuel utilisateur

Joining Instruction for

Medium Temperature

Single Deck Wall and

Wide Island Merchandisers

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Merchandisers

For Medium Temperature Merchandisers

PARTS LIST

Item Quantity Description

Wall Island

1. 11 Gasket 1/2x 1/2x 120

2. 10 Gasket 1/2x 15/8x 180

3. 45 Cap Screw 5/16 -18 x 11/4

4. 57 Flat Washer 5/16

5. 45 Lock Washer 5/16

6. 12 Hex Nut 5/16 -18

7. 11 Silicone

8. 14 Butyl Tape

912 Splashguard Joint Support

10. 48 Screw, Hex Head SM #8 x 1/2

Note: Nut retainers are factory installed in the left end, and alignment pins are factory installed

in the right end of merchandiser.

NOTE: Be sure merchandisers

have been leveled according to the

installation instructions to assure

good fit and finish of the lineup. Be

sure factory-installed nut retainers

and alignment pins are in place.

1Remove shelves (if installed),

display racks, pans, front shelf

supports and front air grilles

from the right end as shown in

Figure 1.

Remove and discard shipping

braces and associated hardware.

PW, PWW, PWR, MWG

M1E/M1GE

Removable Front

Shelf Supports

Removable

Return

Air Grilles

P/N 0376452D

January, 2003

Figure 1. Removing Shelf Supports and Return Air Grilles

Wall Case: Use a narrow

(3/32 or smaller) rod to lift the

honeycomb and remove it from

its retainer as shown in Figure 2.

Remove the back panel from the

right end by lifting up from its

bottom edge and out. Do not use

sharp tools.

Island Case: Use a small

screwdriver to lift and remove

the discharge grilles from both

sides of center flue as shown in

Figure 3.

P/N 0376452D

Merchandisers

2HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Discharge Grille

Island Center Flue

Honeycomb

Retainer

Figure 2. Removing Honeycomb

Figure 3. Removing Discharge Grilles

2Verify that nut retainers and

alignment pins are installed in

the right-hand end of the left

merchandiser in the locations

shown in Figure 4.

Single Deck Merchandiser Joining Instruction P/N 0376452D

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Alignment Pins

Alignment

Pins

Alignment

Pins

Figure 4. Retainer and Alignment Pin Locations

Front Detail

Alignment Pins

3Apply Gasket – 1 in the hori-

zontal recess across the bottom

and up front to cover slots,

including glass front (if

applicable). Apply Gasket – 2

to cover foam-to-metal gap at

rear and across top as shown in

Figure 5.

• Lap gaskets at lower corners.

• Check that there are no gaps

between gasket and

merchandiser.

• Do not stretch gasket,

especially around corners.

• Do not butt gaskets; always

lap joints.

• Remove paper backing after

gasket is applied.

P/N 0376452D

Merchandisers

4HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Figure 5. Installing Gaskets/Silicone

Front Detail

Glass Front Detail

1 5/8in. Gasket

1/2in. Gasket

4Move second Merchandiser

against first, mating alignment

pins with corresponding holes.

Always push merchandisers

together, do not pull together.

Using the front support bracket

holes, fasten fronts together

using

Cap Screw – 3,

Flat Washers – 4,

Lock Washers – 5, and

Hex Nut – 6.

Tighten only until front panels

touch. Do not tighten fully.

Island Case: Use

Cap Screws – 3 with

Flat Washers – 4 and

Lock Washers – 5 to draw

merchandisers together using

nut retainers at center flue as

shown in Figure 6. Tighten until

gaskets are compressed.

Wall Case: Use

Cap Screws – 3 with

Flat Washers – 4 and

Lock Washers – 5 to draw

merchandisers together using

nut retainers at rear as shown in

Figure 7. Start at the bottom,

below the coil baffle, working

your way up to the top; tighten

until gaskets are compressed.

Single Deck Merchandiser Joining Instruction P/N 0376452D

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Alignment Pins

Nut Retainer

3 Places

DETAIL

SEE DETAIL

Fasten in Order Shown

Figure 6. Joining Island Cases

Alignment

Pins

Fasten in Order Shown

Figure 7. Joining Wall Cases

5Apply Silicone – 7 to area

across front support brackets

and down, stopping at bottom

joint, as shown in the Front

Details in Figure 8.

Apply Butyl Tape – 8 across

bottom joint, as shown in

Figures 8 and 9.

P/N 0376452D

Merchandisers

6HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Front Detail

Glass Front Detail

Silicone

Butyl Tape

Figure 9. Applying ButylTape

Figure 8. Applying Silicone

6Refer to Installation &

Operations manual to install

splashguard brackets.

Install Splashguard Joint

Support – 9 using

Screws – 10. Install splash-

guards and lower front panels

according to Installation &

Operations manual and shown in

Figure 9. Install Splashguard as

shown in Figure 10.

7Refer to Installation &

Operations manual 0378414 to

remove/install and offset top rail

and bumpers.

Single Deck Merchandiser Joining Instruction P/N 0376452D

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Figure 9. Installing Splashguard Joint Support

Figure 10. Installing Splashguard

Autres manuels pour IMPACT RL

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hussmann marchandiseur

Hussmann

Hussmann Chino RDI-20 Mode d'emploi

Hussmann

Hussmann M3X-EP Manuel utilisateur

Hussmann

Hussmann IMPACT M1DGE Manuel utilisateur

Hussmann

Hussmann IMPACT Elite ES1 Manuel utilisateur

Hussmann

Hussmann CR3-F Mode d'emploi

Hussmann

Hussmann SGB Mode d'emploi

Hussmann

Hussmann GWIC Manuel utilisateur

Hussmann

Hussmann DVG-8 Guide de démarrage rapide

Hussmann

Hussmann IMPACT RLNIE Mode d’emploi

Hussmann

Hussmann ESBDS Mode d’emploi

Hussmann

Hussmann Q2-SS Instructions d'utilisation d'origine

Hussmann

Hussmann FHMA Manuel utilisateur

Hussmann

Hussmann FN Mode d’emploi

Hussmann

Hussmann IMPACT Excel B1X-GE Mode d’emploi

Hussmann

Hussmann IMPACT Excel C2NX-LE Mode d’emploi

Hussmann

Hussmann C2NX-XLGE Mode d’emploi

Hussmann

Hussmann CGDM Manuel utilisateur

Hussmann

Hussmann VBL Manuel utilisateur

Hussmann

Hussmann P4X-EP Mode d’emploi

Hussmann

Hussmann M4NX-GEP Mode d’emploi

Hussmann

Hussmann Impact P1 Manuel utilisateur

Hussmann

Hussmann IMPACT Excel D6X-ULEP Mode d’emploi

Hussmann

Hussmann SPECIALTY TY3-3X4.5E-R Manuel utilisateur

Hussmann

Hussmann IMPACT Elite E2SPH Manuel utilisateur

Manuels marchandiseur populaires d'autres marques

FRIGOGLASS

FRIGOGLASS Flex 20 HC Manuel utilisateur

EPTA

EPTA COSTAN RHINO MULTI Manuel utilisateur

CASCO

CASCO Nano Cube Manuel utilisateur

True

True GDIM-26 Manuel utilisateur

Structural Concepts

Structural Concepts Oasis Mobile Series Instructions d'installation

Haussmann

Haussmann RL Manuel utilisateur

Howard McCray

Howard McCray R-CDS32E-4 Manuel utilisateur

EPTA

EPTA iarp Cool Emotions Delight Lite Manuel utilisateur

VALERA

VALERA BC 85 Manuel utilisateur

HL Display

HL Display 3eBin Manuel utilisateur

Dixie Narco

Dixie Narco DNCB 501E Manuel utilisateur

APW Wyott

APW Wyott Racer DMXD-30H Manuel utilisateur

Hoshizaki

Hoshizaki KD-90C Manuel utilisateur

Summit

Summit SCR1006 Manuel utilisateur

Delfield

Delfield Shelleyspeed SPM-28E Manuel utilisateur

EPTA

EPTA iarp Cool Emotions GLEE 40 Manuel utilisateur

Kysor/Warren

Kysor/Warren GranBering KW Mode d’emploi

Crane

Crane BevMAX Refresh 6 Media Manuel utilisateur